Procedures of preparation of numerical analysis,consisting in a simulation of cooperation of three different media: steel,liquid and gas undergoes dynamic load were discussed.Modelling of the initial static load of th...Procedures of preparation of numerical analysis,consisting in a simulation of cooperation of three different media: steel,liquid and gas undergoes dynamic load were discussed.Modelling of the initial static load of the mechanical system was presented.By using the MSC.Software products the following exemplary computer simulations were made: dynamic load impact on the hydraulic leg as well as effectiveness of the hydraulic leg protection against overload with help of gas accumulator.展开更多
Humidification is an important step in humid air turbine system. The calculation on humidification is carried out at 423.15—573.15K, 5—15MPa. The results suggest that to produce high-enthalpy moist air, high water t...Humidification is an important step in humid air turbine system. The calculation on humidification is carried out at 423.15—573.15K, 5—15MPa. The results suggest that to produce high-enthalpy moist air, high water temperature and large water flow are needed. The water temperature is the most sensitive parameter to the humidification tower. And it is better for the humidification tower to work at temperature higher than 523 K when the system pressure is higher than 5 MPa. The comparison between the model used in this paper and ideal model shows that the ideal model can be used in simulation to simply the calculation when the temperature is lower than 473 K and pressure is lower than 5 MPa.展开更多
In order to study the basic characteristics of gas flow field in the atomizing chamber near the nozzle outlet of the vortical loop slit atomizer and its influence mechanism on clogging phenomenon,the computational flu...In order to study the basic characteristics of gas flow field in the atomizing chamber near the nozzle outlet of the vortical loop slit atomizer and its influence mechanism on clogging phenomenon,the computational fluid dynamics(CFD)software Fluent is used to conduct a numerical simulation of the gas flow field in the atomizing chamber near the nozzle outlet of this atomizer under different annular slit widths,different atomization gas pressures and different protrusion lengths of the melt delivery tube. The results show that under atomization gas pressure p=4.5 MPa,the greater the annular slit width D,the lower the static temperature near the central hole outlet at the front end of the melt delivery tube,and the smaller the aspirating pressure at the front end of the melt delivery tube. These features can effectively prevent the occurrence of the clogging phenomenon of metallic melt. Under an annular slit width of D=1.2 mm,when the atomization gas pressure satisfies 1 MPa ≤ p ≤ 2 MPa and increases gradually,the aspirating pressure at the front end of the melt delivery tube will decline rapidly. This can prevent the clogging phenomenon of metallic melt. However,when the atomization gas pressure p >2 MPa,the greater the atomization gas pressure,the lower the static temperature near the central hole outlet at the front end of the melt delivery tube,and the greater the aspirating pressure at the front end of the melt delivery tube. Hence,the effect of preventing the solidification-induced clogging phenomenon of metallic melt is restricted. When atomization gas pressure is p =4.5 MPa and annular slit width is D=1.2 mm,the greater the protrusion length H of the melt delivery tube,and the smaller the aspirating pressure at its front end. The static temperature near the central hole that can be observed in its front end is approximate to effectively prevent the occurrence of clogging phenomenon of metallic melt. However,because of the small aspirating pressure,the metallic melt flows into the atomizing chamber from the central hole at the front end of the melt delivery tube at an increasing speed and the gas-melt ratio in the mass flow rate is reduced,which is not conducive to the improvement of atomization performance.展开更多
In order to study the pressure characteristics of slug flow in horizontal curved tubes,two kinds of curved tubes with central angle 45° and 90° respectively are studied,of which are with 0. 5m circumference ...In order to study the pressure characteristics of slug flow in horizontal curved tubes,two kinds of curved tubes with central angle 45° and 90° respectively are studied,of which are with 0. 5m circumference and 26 mm inner diameter are used. When the superficial liquid velocity or the superficial gas velocity is constant,the pressure fluctuations and the probability distribution of the average velocity of slug flow are clear for all of the five experimental conditions. The results of experiment show that the pressure characteristics of slug flow in curved tubes have periodic fluctuations. With the rise of central angle,the period of pressure fluctuation is more obvious. The system pressure of the slug flow increases with the increasing of superficial liquid/gas velocity. Meanwhile,the probability distribution of pressure signal shows regularity,such as unimodal,bimodal or multimodal.展开更多
This paper is concerned with a remedy for interface smearing,which is usable when fixed (i.e. non moving and so non conforming) grids are employed. It is simple to employ and has been found to be rather effective. T...This paper is concerned with a remedy for interface smearing,which is usable when fixed (i.e. non moving and so non conforming) grids are employed. It is simple to employ and has been found to be rather effective. The paper explains its principle, describes how it has been implemented and presents some results obtained with its assistance. The results are compared both with those of earlier methods of interface motion calculation and with experimental data.展开更多
The injection of a high pressure gas into a stagnant liquid pool is the characteristic phenomenon during the expansion phase of a hypothetical core disruptive accident in liquid metal cooled fast reactors. In order to...The injection of a high pressure gas into a stagnant liquid pool is the characteristic phenomenon during the expansion phase of a hypothetical core disruptive accident in liquid metal cooled fast reactors. In order to investigate lots of mechanisms involved in this phase of the accident＇s evolution, an experimental campaign called S GI was performed in 1994 in Forschungszentrum Karlsruhe, now KIT. This campaign consists of nine experiments which have been dedicated to assess the effects of different pressure injection, the nozzle＇s size and the presence of inner confinement in the formation of the rising bubble. Three of these experiments, which were focused on the pressure effects, have now been simulated with SIMMER III code and with FLUENT 6.3, a commercial CFD code. Both codes, despite their different features, have showed a good agreement with the experimental results. In particular, time trend evolutions of pressures and bubble volumes have been well reproduced by simulation. Furthermore, both codes agree on the shape of the bubble, even though they have evidenced same discrepancies with the experimental shape.展开更多
As a critical facility,spiral-wound heat exchanger was(SWHE)has the been widely used in many industrial applications.boundary A computational fluid dynamics(CFD)model employed with smallest periodic element results an...As a critical facility,spiral-wound heat exchanger was(SWHE)has the been widely used in many industrial applications.boundary A computational fluid dynamics(CFD)model employed with smallest periodic element results and periodic conditions to examine around the the characteristics tube of the shell side of SWHE.Numerical simulation show that the heat transfer coefficients and initially mean increase absolute and subsequently decrease simulated 5%with heat radial angle because of the influence measured of backflow turbulent separation.nitrogen The deviation between is transfer coefficients and values for methane,drop,ethane,and are a mixture(methane/ethane)within when mean Reynolds number is over is 30000.For the pressure the simulated results values smaller than the measured values,and the absolute on deviation within 9%.Numerical simulation also tubes indicate that the pressure drop the and heat of transfer coefficients angle the shell side and of SWHE heat decrease as the winding the angle of the increases.Nusselt Considering effect winding on pressure drops transfer coefficients,modified correlations of_=0.308Re^(0.64)Pr^(0.36)(1+sin)^(1.38 )and friction factor f_=0.435Re^(-0.133)(sin)^(-0.36),are proposed.Comparing Nu number with the experimental data,the maximum deviations for heat transfer coefficients and pressure drops are less than 5%and11%respectively.展开更多
In this paper, by introducing the flow velocity item into the classical Rayleigh-Plesset dynamic equation, a newequation, which does not involve the time term and can describe the motion of cavitation bubble in the st...In this paper, by introducing the flow velocity item into the classical Rayleigh-Plesset dynamic equation, a newequation, which does not involve the time term and can describe the motion of cavitation bubble in the steadycavitating flow, has been obtained. By solving the new motion equation using Runge-Kutta fourth order methodwith adaptive step size control, the dynamic behaviors of cavitation bubble driven by the varying pressure fielddownstream of a venturi cavitation reactor are numerically simulated. The effects of liquid temperature (correspondingto the saturated vapor pressure of liquid), cavitation number and inlet pressure of venturi on radial motionof bubble and pressure pulse due to the radial motion are analyzed and discussed in detail. Some dynamicbehaviors of bubble different from those in previous papers are displayed. In addition, the internal relationshipbetween bubble dynamics and process intensification is also discussed. The simulation results reported in thiswork reveal the variation laws of cavitation intensity with the flow conditions of liquid, and will lay a foundationfor the practical application of hydrodynamic cavitation technology.展开更多
文摘Procedures of preparation of numerical analysis,consisting in a simulation of cooperation of three different media: steel,liquid and gas undergoes dynamic load were discussed.Modelling of the initial static load of the mechanical system was presented.By using the MSC.Software products the following exemplary computer simulations were made: dynamic load impact on the hydraulic leg as well as effectiveness of the hydraulic leg protection against overload with help of gas accumulator.
基金Supported by the Natural Science Foundation of Jiangsu Province (BK97124) the National Natural Science Foundation (No. 20376032)+1 种基金 the Outstanding Youth Fund of National Natural Science Foundation (No. 29925616)Key Fund of National Natural Science Fo
文摘Humidification is an important step in humid air turbine system. The calculation on humidification is carried out at 423.15—573.15K, 5—15MPa. The results suggest that to produce high-enthalpy moist air, high water temperature and large water flow are needed. The water temperature is the most sensitive parameter to the humidification tower. And it is better for the humidification tower to work at temperature higher than 523 K when the system pressure is higher than 5 MPa. The comparison between the model used in this paper and ideal model shows that the ideal model can be used in simulation to simply the calculation when the temperature is lower than 473 K and pressure is lower than 5 MPa.
基金supported by the Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD)the Simulation and Test of the Flow Field of Gas Atomization Nozzle (No. 1001-KFA19184)。
文摘In order to study the basic characteristics of gas flow field in the atomizing chamber near the nozzle outlet of the vortical loop slit atomizer and its influence mechanism on clogging phenomenon,the computational fluid dynamics(CFD)software Fluent is used to conduct a numerical simulation of the gas flow field in the atomizing chamber near the nozzle outlet of this atomizer under different annular slit widths,different atomization gas pressures and different protrusion lengths of the melt delivery tube. The results show that under atomization gas pressure p=4.5 MPa,the greater the annular slit width D,the lower the static temperature near the central hole outlet at the front end of the melt delivery tube,and the smaller the aspirating pressure at the front end of the melt delivery tube. These features can effectively prevent the occurrence of the clogging phenomenon of metallic melt. Under an annular slit width of D=1.2 mm,when the atomization gas pressure satisfies 1 MPa ≤ p ≤ 2 MPa and increases gradually,the aspirating pressure at the front end of the melt delivery tube will decline rapidly. This can prevent the clogging phenomenon of metallic melt. However,when the atomization gas pressure p >2 MPa,the greater the atomization gas pressure,the lower the static temperature near the central hole outlet at the front end of the melt delivery tube,and the greater the aspirating pressure at the front end of the melt delivery tube. Hence,the effect of preventing the solidification-induced clogging phenomenon of metallic melt is restricted. When atomization gas pressure is p =4.5 MPa and annular slit width is D=1.2 mm,the greater the protrusion length H of the melt delivery tube,and the smaller the aspirating pressure at its front end. The static temperature near the central hole that can be observed in its front end is approximate to effectively prevent the occurrence of clogging phenomenon of metallic melt. However,because of the small aspirating pressure,the metallic melt flows into the atomizing chamber from the central hole at the front end of the melt delivery tube at an increasing speed and the gas-melt ratio in the mass flow rate is reduced,which is not conducive to the improvement of atomization performance.
基金Supported by the National Natural Science Foundation of China(No.5130416)
文摘In order to study the pressure characteristics of slug flow in horizontal curved tubes,two kinds of curved tubes with central angle 45° and 90° respectively are studied,of which are with 0. 5m circumference and 26 mm inner diameter are used. When the superficial liquid velocity or the superficial gas velocity is constant,the pressure fluctuations and the probability distribution of the average velocity of slug flow are clear for all of the five experimental conditions. The results of experiment show that the pressure characteristics of slug flow in curved tubes have periodic fluctuations. With the rise of central angle,the period of pressure fluctuation is more obvious. The system pressure of the slug flow increases with the increasing of superficial liquid/gas velocity. Meanwhile,the probability distribution of pressure signal shows regularity,such as unimodal,bimodal or multimodal.
文摘This paper is concerned with a remedy for interface smearing,which is usable when fixed (i.e. non moving and so non conforming) grids are employed. It is simple to employ and has been found to be rather effective. The paper explains its principle, describes how it has been implemented and presents some results obtained with its assistance. The results are compared both with those of earlier methods of interface motion calculation and with experimental data.
文摘The injection of a high pressure gas into a stagnant liquid pool is the characteristic phenomenon during the expansion phase of a hypothetical core disruptive accident in liquid metal cooled fast reactors. In order to investigate lots of mechanisms involved in this phase of the accident＇s evolution, an experimental campaign called S GI was performed in 1994 in Forschungszentrum Karlsruhe, now KIT. This campaign consists of nine experiments which have been dedicated to assess the effects of different pressure injection, the nozzle＇s size and the presence of inner confinement in the formation of the rising bubble. Three of these experiments, which were focused on the pressure effects, have now been simulated with SIMMER III code and with FLUENT 6.3, a commercial CFD code. Both codes, despite their different features, have showed a good agreement with the experimental results. In particular, time trend evolutions of pressures and bubble volumes have been well reproduced by simulation. Furthermore, both codes agree on the shape of the bubble, even though they have evidenced same discrepancies with the experimental shape.
基金supported by Beijing Natural Science Foundation(Grant No.3171002)
文摘As a critical facility,spiral-wound heat exchanger was(SWHE)has the been widely used in many industrial applications.boundary A computational fluid dynamics(CFD)model employed with smallest periodic element results and periodic conditions to examine around the the characteristics tube of the shell side of SWHE.Numerical simulation show that the heat transfer coefficients and initially mean increase absolute and subsequently decrease simulated 5%with heat radial angle because of the influence measured of backflow turbulent separation.nitrogen The deviation between is transfer coefficients and values for methane,drop,ethane,and are a mixture(methane/ethane)within when mean Reynolds number is over is 30000.For the pressure the simulated results values smaller than the measured values,and the absolute on deviation within 9%.Numerical simulation also tubes indicate that the pressure drop the and heat of transfer coefficients angle the shell side and of SWHE heat decrease as the winding the angle of the increases.Nusselt Considering effect winding on pressure drops transfer coefficients,modified correlations of_=0.308Re^(0.64)Pr^(0.36)(1+sin)^(1.38 )and friction factor f_=0.435Re^(-0.133)(sin)^(-0.36),are proposed.Comparing Nu number with the experimental data,the maximum deviations for heat transfer coefficients and pressure drops are less than 5%and11%respectively.
基金support of the National Natural Science Foundation of China (Grant No. 50806078)the National High-Tech Research and Development Program of China (863 Program, Grant No. 2006AA05Z203).
文摘In this paper, by introducing the flow velocity item into the classical Rayleigh-Plesset dynamic equation, a newequation, which does not involve the time term and can describe the motion of cavitation bubble in the steadycavitating flow, has been obtained. By solving the new motion equation using Runge-Kutta fourth order methodwith adaptive step size control, the dynamic behaviors of cavitation bubble driven by the varying pressure fielddownstream of a venturi cavitation reactor are numerically simulated. The effects of liquid temperature (correspondingto the saturated vapor pressure of liquid), cavitation number and inlet pressure of venturi on radial motionof bubble and pressure pulse due to the radial motion are analyzed and discussed in detail. Some dynamicbehaviors of bubble different from those in previous papers are displayed. In addition, the internal relationshipbetween bubble dynamics and process intensification is also discussed. The simulation results reported in thiswork reveal the variation laws of cavitation intensity with the flow conditions of liquid, and will lay a foundationfor the practical application of hydrodynamic cavitation technology.
