不可溶漂浮性液态污染物向下层水体释放研究

漂浮于水面的不可溶液态污染物的物理性质是影响其向下层水体释放强度的重要因素。根据有机污染物物理性质及相关参数的分布范围,筛选出8种代表性不可溶漂浮性液态污染物,按不同比例配制32种混合样品,共计40种样品。其中39种典型研究样品的密度、运动黏度、表面张力范围分别为0.621~0.995g/cm^(3)、1.81×10^(-6)~1.00×105mm^(2)/s、0.024~36.200 mN/m。在39种典型样品中选择34种进行实验室动水环境物理试验,分别研究了污染物密度、运动黏度、表面张力对释放强度的影响。采用偏相关分析方法识别了影响释放强度的关键物理因素,结果表明密度、运动黏度是影响释放强度的决定性因素,表面张力对释放强度无显著影响。采用回归分析方法构建释放强度与密度、运动黏度间的多元非线性回归模型(R^(2)=0.987)。用39种典型样品中余下5种样品独立试验数据对模型进行的验证表明平均相对误差为14.9%。

Influence of technical parameters on strength and ductility of AlSi9Cu3 alloys in squeeze casting

An orthogonal test was conducted to investigate the influence of technical parameters of squeeze casting on the strength and ductility of AISigCu3 alloys. The experimental results showed that when the forming pressure was higher than 65 MPa, the strength （ab） of A1Si9Cu3 alloys decreased with the forming pressure and pouring temperature increasing, whereas ab increased with the increase of filling velocity and mould preheating temperature. The ductility （6） by alloy was improved by increasing the forming pressure and filling velocity, but decreased with pouring temperature increasing. When the mould preheating temperature increased, the ductility increased first, and then decreased. Under the optimized parameters of pouring temperature 730 ℃, forming pressure 75 MPa, filling velocity 0.50 m/s, and mould preheating temperature 220 ℃, the tensile strength, elongation, and hardness of A1Si9Cu3 alloys obtained in squeeze casting were improved by 16.7%, 9.1%, and 10.1%, respectively, as compared with those of sand castings.

Study on Polymorphisms in the Blood Protein of Tibetan Mastiff

[ Objective] The aim was to study the protein polymorphism in the blood of Tibetan Mastiff, and provide some theoretical basis for resource protection and reasonable development and utilization of Tibetan Mastiff varieties. [ Method] A total of 103 blood samples were taken from four populations of Hequ Tibetan Mastiff, Qinhai Tibetan Mastiff, Tibetan Spaniel and native dogs of Qinghai. Seven blood protein Iocus（Tf, Po, Sα2, Hb, AIb, Pr and Amy）were investigated by using vertical polyacrylamide gel electrophoresis with discontinuous buffer system. Then the genetic variation during different populations was analyzed. [ Result] Genetic variations were observed in Tf, Sα2 and Po in four populations, others were not polymorphic. There were three alleles at the locus of Tf and Po, two alleles at the loci of Sα2. Effective number of alleles and Nei＇s average expected heterozygosity were 1. 532 4 and 0.230 3 relatively, all higher in Tibetan Mastiff than other populations. [ Conclusion] Protein locus in blood of Tibetan Mastiff existed in genetic variation.

Analysis and Experimental Identification of Torsional Dynamic Characteristics of Hydrodynamic Torque Converter

The subsection linear torsional model of hydrodynamic torque converter was established and further simplified. According to the identification theory, the frequency characteristic was achieved with the Matlab/ Ident toolbox. Then parametric model was established by adopting the subsection linearization method, and the damp value was estimated. The curve and function of damp changing with speed ratio was also established by fitting. In order to validate the identification results, the experimental output was compared with the output of the model in which torque was chosen as input signal and speed as output signal in Matlab/Ident toolbox. It was shown that model output is in good agreement with experimental output.

Effects of Continuous Irrigation of Biogas Slurry on Forms and Biological Availability of Pb in Soil of a Tea Garden

Through indoor culture experiments, the effects of continuous irrigation of biogas slurry on the forms and biological availability of Pb in soil of a tea garden were studied. The results show that continuous irrigation of biogas slurry could change the forms of Pb in the soil, and exchangeable Pb, Pb bonded to iron and manganese oxides, and Pb bonded to carbonates transformed to Pb bonded to or- ganic matter and residual Pb in the soil. Among various forms of Pb in the soil, the content of residual Pb was the highest in the soil irrigated with biogas slurry contin- uously in various treatments, accounting for 54.56%, 60.00% and 60.70% in the treatments T1, T2 and T3 respectively. Compared with the CK, the application of bio- gas slurry could decrease the biological activity and biological availability of Pb in the soil obviously, and the reduction of the biological activity was 21.26%-22.83%. In a word, the application of biogas slurry in soil of the tea garden could inhibit the biological activity and biological availability of Pb.

信息化时代弹箭用液态流程性材料质量控制研究

综述信息化时代弹箭用液态流程性材料的过程控制、应用及意义。

Effects of Probiotics on Growth Performance and Blood Biochemical Indexes of Cherry Valley Ducks

In order to investigate the effects of probiotics on growth performance, blood biochemical indexes and economic benefits of Cherry Valley ducks, different probiotics were added into the feed of Cherry Valley ducks. Total 240 1-d-old Cherry Valley ducks were selected, and they were randomly divided into 4 groups, including 1 control group and 3 treatment groups. There were 3 replicates for each group and there were 20 ducks for each replicate. The ducks in the control group were fed the basal diet, and the ducks in the 3 treatment groups were fed the basal diet added with Lactobacillus, Bacillus natto and florfenicol, respectively. The test lasted for 42 d. The results showed that the addition of Lactobacillus and Bacillus natto could improve the average daily weight gain and final average weight （P〈0.05） of Cherry Valley ducks, and reduce the glutamic-pyruvic transaminase ac- tivity, alkaline phosphatase activity and serum urinary nitrogen content in duck blood （P〈0.05） and reduce the creatinine content and total cholesterol content in Cherry Valley ducks （P〉0.05）; at the same time, adding probiotics to feed could also in- crease the grass economic benefits of Cherry Valley ducks. In overall, the effects of adding probiotics were better than those of adding antibiotic.

Screening of a Novel Bioflocculant-producing Strain and Research on Its Flocculation

[Objective] This study aimed to screen a bacterial strain capable of producing bioflocculant. [Method] A bacterial strain T-11 capable of producing bioflocculant was isolated from activated sludge. Detailed tests on the morphological, physiological and biochemical characteristics were carried out and identification was performed to identify the strain. Finally, the bioflocculant was isolated and purified, and the flocculating activity and chemical characteristics were measured. [Result] It was identified as Serratia plumuthica based on its morphological, physiological and biochemical characteristics. This strain secreted flocculant best in a culture medium which included sucrose and NaNO3. The maximal cell growth was achieved within 10 h and the flocculating activity paralleled to it. It was found to be effective for flocculation of kaolin suspension, when added at a final concentration of 0.7 mg/L, over a range of pHs （2-7）, and temperature （approximately 30-80 ℃）. Chemical analysis indicated that the bioflocculant was an acidic polysaccharide consisting of glucose, glucuronic acid and galactose, talose and altrose. Infrared spectrum analysis also revealed typical characteristics of polysaccharides. [Conclusion] The biofloccu- lants produced by strain T-11 can greatly improve the ability of activated sludge to settle.

Pharmacodynamic and kinetic effect of rabeprazole on serum gastrin level in relation to CYP2C19 polymorphism in Chinese Hans

AIM： To observe the pharmacokinetics and pharmacodynamics of rabeprazole and compare serum gastrin concentrations in different CYP2C19 genotype groups. METHODS： The CYP2C19 genotype status of Chinese Han healthy volunteers was determined by polymerase chain reaction-restriction fragment length polymorphism method. Twenty H pylori-negative healthy subjects voluntary participated in the study. They were divided into the following three groups： homozygous extensive metabolizers （homEM）, heterozygous extensive metabolizers （hetEM） and poor metabolizers （PM）. After they orally received rabeprazole 20 mg once daily in the morning of d 1 and d 8, blood samples were collected at various time-points until 24 h after administration and intragastric pH values were monitored for 24 h by Digitrapper pH. Serum gastrin concentrations were measured by radioimmunoassay. Serum concentrations of rabeprazole were measured by high performance liquid chromatography. RESULTS： The mean AUC values for rabeprazole after a single and repeated doses were significantly different between the homEM and PM groups, but not between the homEM and hetEM, or the hetEM and PM groups. No significant differences in intragastric pH medians were observed among the three different genotype groups after a single dose or repeated doses. The ratio of pH medians between d 1 and d 8 ranged from 84% to 108%. The mean gastrin AUC values were also different among the three genotype groups, with a relative ratio of 1.0, 1.2 and 1.5 after a single dose and 1.0, 1.5 and 1.6 after repeated doses in the homEM, hetEM and PM groups, respectively. The gastrin AUC values among the three different genotype groups showed no significant difference either after a single dose or repeated doses. The subject who had lower intragastric acidity showed higher serum gastrin levels and concentrations of rabeprazole. CONCLUSION： In Chinese Han healthy people, the pharmacokinetics of rabeprazole are dependent on the CYP2C19 genotype status, but acid-inhibitory efficacy of rabeprazole and the gastrin level are not influenced significantly.

Determination of risperidone in human plasma by HPLC-MS/MS and its application to a pharmacokinetic study in Chinese volunteers

This study presents a rapid, specific and sensitive liquid chromatography/tandem mass spectrometry (LC-MS/MS) assay for determination of risperidone (RIS) in human serum using paroxetine as an internal standard (IS). An Alltima-C18 column (2.1 mm×100 mm, 3 μm) and a mobile phase consisting of 0.1% formic acid-acetonitrile (40:60, v/v) were used for separation. The analysis was performed by selected reaction monitoring (SRM) method, and the peak area of the m/z 411.3→191.1 transition for RIS was measured versus that of the m/z 330.1→192.1 transition for IS to generate the standard curves. The assay linearity of RIS was confirmed over the range 0.25～50.00 ng/ml and the limit of quantitation was 0.05 ng/ml. The linear range corresponds well with the serum concentrations of the analytes obtained in clinical pharmacokinetic studies. Intraday and interday relative standard deviations were 1.85%～9.09% and 1.56%～4.38%, respectively. The recovery of RIS from serum was in the range of 70.20%～84.50%. The method was successfully applied to investigate the bioequivalence between two kinds of tablets (test versus reference products) in 18 healthy male Chinese volunteers. The result suggests that two formulations are bioequivalent.

Combined goblet cell carcinoid and mucinous cystadenoma of the vermiform appendix

Goblet cell carcinoid is an uncommon primary tumor of the vermiform appendix, characterized by dual endocrine and glandular differentiation. Whether goblet cell carcinoid represents a morphological variant of appendiceal classical carcinoid or a mucin-producing adenocarcinoma is a matter of conjecture. Rare cases of goblet cell carcinoid with other concomitant appendiceal epithelial neoplasms have been documented. In this report, we describe a rare case of combined appendiceal goblet cell carcinoid and mucinous cystadenoma, and discuss the possible histopathogenesis of this combination.

Thermodynamic properties and heat capacity of Ru metal in HCP,FCC,BCC and liquid state

Isometric heat capacity cv and isobar heat capacity cp of Ru metal in HCP,FCC,BCC and liquid state were calculated by using pure element systematic theory.The results are in good agreement with joint army-navy-air force(JANAF) experimental value and the calculation result by first-principle(FP) method.But the results have great differences in contrast to Scientific Group Thermodata Europe(SGTE) database.The cause is found that it cannot neglect the electron devotion to heat capacity to adjust cp in one-atom(OA) method.The disparity between OA method and SGTE database was discussed.The main cause is that OA method adopts the crosspoint with iso-Ec-line and iso-a-line in hybritriangle to determine the properties,but SGTE database is obtained by extrapolation from activity measurements and critical assessment of data from a large number of binary system.Thermodynamic properties of Ru metal in HCP,FCC,BCC and liquid state,such as entropy S,enthalpy H and Gibbs energy G were calculated.Therefore,the full description of thermodynamic properties from 0 K to random temperature is implemented.

Forming properties and microstructure of Al-Cu alloy prepared by liquid-die forging

The Al-Cu wheel adopting the new Al alloy was prepared by the liquid-die forging,and the mechanical properties,composition distribution,microstructure and fracture behavior were investigated.The results showed that serious Cu segregation was found in the wheel specimen;the microstructure of the Al-Cu wheel was comprised of the casting microstructure and a small amount of the deformed microstructure;the best heat treatment and water quenching system were found to solution treated at(530±5)℃ for 4 h followed by(535±5)℃ for 24 h and aging treated at(155±5)℃ for 4 h;the fracture morphologies of the samples heated under T 6 and T 5-1 heat treatment showed flat,tough nest,and poor plastic characteristics;the fracture morphologies of the samples heated under T 4 heat treatment exhibited complete resilience,but no residual metallographic characteristic;the sample treated under T 4 protocol had the best elongation;the fracture failure was mainly due to the formation of the CuAl_(2)(θ)phases;and the fracture mechanism of the Al-Cu wheel was intergranular fracture.

Liquid Flow in Shaped Fiber Bundle

By computation and comparison of the critical spreading coefficient parameter, it was found that shaped fiber bundle is better for wetting. Liquid-air interface tension of liquid arising the shaped fiber bundle body is considered as one critical factor besides liquid viscosity, inertia force and liquid-fiber interface tension. Experimental result simulation demonstrated that the liquid-air interface tension is correlated with the geometric size of the liquid arising in body, Φ0 （x） and which is affected by the cross sectional shape of fiber and the radius of single fiber. The shaped fiber bundle model is/ntroduced to/nvestigate liquid flow in fiber assembly. The model is generated based on a random function for stochastic forming of fibers in bundle and it is necessary to combine this fundamental model with physical explanation for investigation of liquid flow in fiber assembly.

Simulation and experimental study of 7A09 aluminum alloy milling under double liquid quenching

To explore the influence of double liquid quenching on the cutting performance of the 7A09 aluminum alloy,quasi-static compression and dynamic impact tests were carried out on the 7A09 aluminum alloy after double liquid quenching using an MTS810.23 universal testing machine and split-Hopkinson pressure bar(SHPB).The experimental data were fitted to obtain the Johnson–Cook constitutive model parameters of the alloy.Simulations of the machining process were carried out using the Deform-3D finite element software.The results showed that the rheological stress increased with the increase in strain rate and the decrease in temperature.The increase in the cutting speed and feed caused the cutting temperature to rise sharply,whereas the influence of the cutting amount on the cutting temperature was weak.Because of the presence of chip nodules,there was extremum in the cutting force vs cutting speed curves.The increase in the feed and cutting depth increased the cutting area Ac,so the cutting force also increased.The simulation results were verified by experiments.The simulation predictions were in good agreement with the test values,and the cutting force and temperature variations with the cutting parameters were the same.Thus,the correctness of the 7A09 aluminum alloy finite element model was verified.

Effect of Si content on interfacial reaction and properties between solid steel and liquid aluminum

The effect of Si content on the microstructures and growth kinetics of intermetallic compounds(IMCs)formed during the initial interfacial reaction(<10 s)between solid steel and liquid aluminum was investigated by a thermophysical simulation method.The influence of Si addition on interfacial mechanical properties was revealed by a high-frequency induction brazing.The results showed that IMCs layers mainly consisted ofη-Fe_(2)Al_(5)andθ-Fe_(4)Al_(13).The addition of Si reduced the thickness of the IMCs layer.The growth of theηphase was governed by the diffusion process when adding 2 wt.%Si to the aluminum melt.When 5 wt.%or 8 wt.%Si was added to aluminum,the growth was governed by both the diffusion process and interfacial reaction,and ternary phaseτ1/τ9-(Al,Si)_(5)Fe_(3)was formed in theηphase.The apparent activation energies of theηphase decreased gradually with increasing Si content.The joint with pure aluminum metal had the highest tensile strength and impact energy.

Stability of Stratified Gas-Liquid Flow in Horizontal and Near Horizontal Pipes

A viscous Kelvin-Helmholtz criterion of the interfacial wave instability is proposed in this paper based on the linear stability analysis of a transient one-dimensional two-fluid model. In thismodel, the pressure is evaluated using the local momentum balance rather than the hydrostatic approximation. The criterion predicts well the stability limit of stratified flow in horizontal and nearly horizontal pipes. The experimental and theoretical investigation on the effect of pipe inclination on the interfacial instability are carded out. It is found that the critical liquid height at the onset of interfacial wave instability is insensitive to the pipe inclination. However, the pipe inclination significantly affects critical superficial liquid velocity and wave velocity especially lor low gas velocities.

Dynamic characteristics of hydraulic power steering system with accumulator in load-haul-dump vehicle

Using hydraulic power steering system of model EIMCO 922 load-haul-dump vehicle as a simulation example, the dynamic characteristics of hydraulic power steering system in load-haul-dump vehicle were simulated and discussed with SIMULINK software and hydraulic control theory. The results show that the dynamic characteristics of hydraulic power steering system are improved obviously by using bladder accumulator, the hydraulic power steering system of model EIMCO 922 load-haul-dump vehicle generates vibration at the initial stage under the normal steering condition of pulse input, and its static response time is 0.25 s shorter than that without bladder accumulator. Under the normal steering working condition, the capacity of steering accumulator for absorbing pulse is directly proportional to the cross section area of connecting pipeline, and inversely proportional to the length of connecting pipeline. At the same time, the precharge pressure of nitrogen in steering accumulator should be 60%80% of the rated minimum working pressure of hydraulic power steering system. Under the abnormal steering working condition, the steering cylinder piston may obtain higher motion velocity, and the dynamic response velocity of hydraulic power steering system can be increased by reducing the pressure drop of hydraulic pipelines between the accumulator and steering cylinder and by increasing the rated pressure of hydraulic power steering system, but the dynamic characteristics of hydraulic power steering system in load-haul-dump vehicle have nothing to do with the precharge pressure of nitrogen in steering accumulator.

Unsteady Motion of a Single Droplet in Surfactant Solutions

A numerical investigation of the unsteady motion of a deformed drop released freely in another quiescent liquid contaminated by surfactant is presented in this paper. The finite difference method was used to solve numerically the coupled time-dependent Navier-Stokes and convective-diffusion equations in a body-fitted orthogonal coordinate system. Numerical simulation was conducted on the experimental cases, in which MIBK drops with the size ranging from 1.24 mm to 1.97 mm rose and accelerated freely in pure water and in dilute sodium dodecyl sulphate (SDS) aqueous solution. The applicability of the numerical scheme was validated by the agreement between the simulation results and the experimental data. Both the numerical and experimental results showed that the velocitytime profile exhibited a maximum rising velocity for drops in SDS solutions, which was close to the terminal velocity in pure water, before it dropped down to a steady-state value. The effect of the sorption kinetics of surfactant on the accelerating motion was also evaluated. It is also suggested that introduction of virtual mass force into the formulation improved obviously the precision of numerical simulation of transient drop motion.