Two kinds of semi-solid samples of AZ80−0.2Y−0.15Ca(wt.%)(AZ80M)magnesium alloy were prepared by semi-solid isothermal heat treatment of materials with and without equal channel angular pressing(ECAP)process.The micro...Two kinds of semi-solid samples of AZ80−0.2Y−0.15Ca(wt.%)(AZ80M)magnesium alloy were prepared by semi-solid isothermal heat treatment of materials with and without equal channel angular pressing(ECAP)process.The microstructures of initial and semi-solid treated samples were compared and analyzed.The results showed a significant difference in the liquid phase distribution between three-pass ECAP processed(3P)and as-received samples during the isothermal heating process.The semi-solid 3P sample showed a more uniform liquid distribution due to its smaller dihedral angle.Besides,the coarsening processes of solid grains of as-received and 3P samples were dominated by the coalescence and Ostwald ripening mechanism,respectively.The difference of coarsening processes was mainly related to the proportion of the high-angle grain boundaries in materials,which further affected the evolution behavior of the liquid pools.展开更多
Aim To develop and validate a RP-HPLC method for the analysis of paclitaxel in a solid dispersion. Methods Paclitaxel and the internal standard norethisterone were separated using a Phenomenex ODS 3 column and monitor...Aim To develop and validate a RP-HPLC method for the analysis of paclitaxel in a solid dispersion. Methods Paclitaxel and the internal standard norethisterone were separated using a Phenomenex ODS 3 column and monitored at a wavelength at 227 nm. The isocratic mobile phase consisting of methanol-acetonitrile-water （40：30：30, V/V） was pumped at a flow-rate of 1.0 mL·min^-1. The dissolution studies were performed according to published studies. Results Under these chromatographic conditions, the calibration curve was linear in the range of 4-40 μg·mL ^-1 with the correlation coefficient of 0.9999. The mean recovery was 98.42 % （RSD = 1.19 %）. At the 60 min time point, the dissolution of paclitaxel from the solid dispersion was nearly 100 %, however, the original form of paclitaxel was about 30 %. Conclusion The method was proven to be specific, accurate and precise for determining the dissolution of paclitaxel from solid dispersion.展开更多
Terephthalic acid(PTA) is practically one of the main materials of polyester. Its corresponding solid-liquid equilibrium data will provide essential support for industry design and further theoretical studies. In this...Terephthalic acid(PTA) is practically one of the main materials of polyester. Its corresponding solid-liquid equilibrium data will provide essential support for industry design and further theoretical studies. In this work,solid-liquid equilibriums of terephthalic acid in four solvents, N,N-dimethylformamide, N,N-dimethylacetamide,dimethylsulphoxide and N-methyl-2-ketopyrrolidene, were determined in the temperature range from 293.15 K to 364.6 K by dynamic method. All these data were regressed by λh model, Wilson model and NRTL model, average absolute relative deviations of which are 1.25%, 15.02% and 7.22% respectively. It indicates that λh model is mostsuitable for description of the solid-liquid equilibrium containing PTA.展开更多
Metastable liquid phase separation and rapid solidification in a metastable miscibility gap were investigated on the Cu60Co30Cr10 alloy by using the electromagnetic levitation and splat-quenching.It is found that the ...Metastable liquid phase separation and rapid solidification in a metastable miscibility gap were investigated on the Cu60Co30Cr10 alloy by using the electromagnetic levitation and splat-quenching.It is found that the alloy generally has a microstructure consisting of a（Co,Cr）-rich phase embedded in a Cu-rich matrix,and the morphology and size of the（Co,Cr）-rich phase vary drastically with cooling rate.During the electromagnetic levitation solidification processing the cooling rate is lower,resulting in an obvious coalescence tendency of the（Co,Cr）-rich spheroids.The（Co,Cr）-rich phase shows dendrites and coarse spheroids at lower cooling rates.In the splat quenched samples the（Co,Cr）-rich phase spheres were refined significantly and no dendrites were observed.This is probably due to the higher cooling rate,undercooling and interface tension.展开更多
The melting process of n-octadecane in a rectangular cavity with three discrete protruding heat sources on its bottom surface was studied experimentally. It was observed that the experimental process, for the geometri...The melting process of n-octadecane in a rectangular cavity with three discrete protruding heat sources on its bottom surface was studied experimentally. It was observed that the experimental process, for the geometric arrangement in this paper, is neither a fixed melting nor a contact melting, but one m which fixed melting and contact melting take place alternatively. The effects of Stefan number, initial subcooling and aspect ratio on the melting process are reported. The larger the Stefan number, the more frequently the contact melting may occur, so does the aspect ratio. The initial subcooling plays a role only in early stage. As the melting process proceeds, its effect on the melting process becomes less.展开更多
基金supported by Key Development Project of Sichuan Province(Grant No.2017GZ0399)。
文摘Two kinds of semi-solid samples of AZ80−0.2Y−0.15Ca(wt.%)(AZ80M)magnesium alloy were prepared by semi-solid isothermal heat treatment of materials with and without equal channel angular pressing(ECAP)process.The microstructures of initial and semi-solid treated samples were compared and analyzed.The results showed a significant difference in the liquid phase distribution between three-pass ECAP processed(3P)and as-received samples during the isothermal heating process.The semi-solid 3P sample showed a more uniform liquid distribution due to its smaller dihedral angle.Besides,the coarsening processes of solid grains of as-received and 3P samples were dominated by the coalescence and Ostwald ripening mechanism,respectively.The difference of coarsening processes was mainly related to the proportion of the high-angle grain boundaries in materials,which further affected the evolution behavior of the liquid pools.
文摘Aim To develop and validate a RP-HPLC method for the analysis of paclitaxel in a solid dispersion. Methods Paclitaxel and the internal standard norethisterone were separated using a Phenomenex ODS 3 column and monitored at a wavelength at 227 nm. The isocratic mobile phase consisting of methanol-acetonitrile-water （40：30：30, V/V） was pumped at a flow-rate of 1.0 mL·min^-1. The dissolution studies were performed according to published studies. Results Under these chromatographic conditions, the calibration curve was linear in the range of 4-40 μg·mL ^-1 with the correlation coefficient of 0.9999. The mean recovery was 98.42 % （RSD = 1.19 %）. At the 60 min time point, the dissolution of paclitaxel from the solid dispersion was nearly 100 %, however, the original form of paclitaxel was about 30 %. Conclusion The method was proven to be specific, accurate and precise for determining the dissolution of paclitaxel from solid dispersion.
基金Supported by China Petroleum & Chemical Corporation(No.200049).
文摘Terephthalic acid(PTA) is practically one of the main materials of polyester. Its corresponding solid-liquid equilibrium data will provide essential support for industry design and further theoretical studies. In this work,solid-liquid equilibriums of terephthalic acid in four solvents, N,N-dimethylformamide, N,N-dimethylacetamide,dimethylsulphoxide and N-methyl-2-ketopyrrolidene, were determined in the temperature range from 293.15 K to 364.6 K by dynamic method. All these data were regressed by λh model, Wilson model and NRTL model, average absolute relative deviations of which are 1.25%, 15.02% and 7.22% respectively. It indicates that λh model is mostsuitable for description of the solid-liquid equilibrium containing PTA.
基金Projects(51171152,50871088) supported by the National Natural Science Foundation of ChinaProject(20126102110048) supported by Doctoral Fund of Ministry of Education of China+2 种基金Project(SKLSP201202) supported by Foundation of State Key Laboratory of Solidification,ChinaProject(2012JC2-02) supported by Natural Science Basic Research Plan in Shaanxi Province,ChinaProject (JC201268) supported by the NPU Foundation for Fundamental Research,China
文摘Metastable liquid phase separation and rapid solidification in a metastable miscibility gap were investigated on the Cu60Co30Cr10 alloy by using the electromagnetic levitation and splat-quenching.It is found that the alloy generally has a microstructure consisting of a（Co,Cr）-rich phase embedded in a Cu-rich matrix,and the morphology and size of the（Co,Cr）-rich phase vary drastically with cooling rate.During the electromagnetic levitation solidification processing the cooling rate is lower,resulting in an obvious coalescence tendency of the（Co,Cr）-rich spheroids.The（Co,Cr）-rich phase shows dendrites and coarse spheroids at lower cooling rates.In the splat quenched samples the（Co,Cr）-rich phase spheres were refined significantly and no dendrites were observed.This is probably due to the higher cooling rate,undercooling and interface tension.
文摘The melting process of n-octadecane in a rectangular cavity with three discrete protruding heat sources on its bottom surface was studied experimentally. It was observed that the experimental process, for the geometric arrangement in this paper, is neither a fixed melting nor a contact melting, but one m which fixed melting and contact melting take place alternatively. The effects of Stefan number, initial subcooling and aspect ratio on the melting process are reported. The larger the Stefan number, the more frequently the contact melting may occur, so does the aspect ratio. The initial subcooling plays a role only in early stage. As the melting process proceeds, its effect on the melting process becomes less.
