The peculiar photoconduction in semi insulating GaAs photoconductive switch being triggered by 1064nm laser pulse is reported.The gap between two electrodes of the switch is 4mm.When it is triggered by laser pulse wi...The peculiar photoconduction in semi insulating GaAs photoconductive switch being triggered by 1064nm laser pulse is reported.The gap between two electrodes of the switch is 4mm.When it is triggered by laser pulse with energy of 0 8mJ and the pulse width of 5ns,and operated at biased electric field of 2 0 and 6 0kV/cm,both linear and nonlinear modes of the switch are observed respectively.Whereas the biased electric field adds to 9 5kV/cm,and the triggered laser is in range of 0 5～1 0mJ,the peculiar performed characteristic is observed:the switch gives a linear waveform firstly,and then after a delay time of about 20～250ns,it outputs a nonlinear waveform again.The physical mechanism of this specific phenomenon is associated with the anti site defects of semi insulating GaAs and two step single photon absorption.The delay time between linear waveform and nonlinear waveform is calculated,and the result matches the experiments.展开更多
Although outstanding microwave power performance of AlGaN/GaN HEMTs has been reported,drain current collapse is still a problem. In this paper,an experiment was carried out to demonstrate one factor causing the collap...Although outstanding microwave power performance of AlGaN/GaN HEMTs has been reported,drain current collapse is still a problem. In this paper,an experiment was carried out to demonstrate one factor causing the collapse. Two AlGaN/GaN samples were annealed under N2-atmosphere with and without carbon incorporation, and the XPS measurement technique was used to determine that the concentration of carbon impurity in the latter sample was far higher than in the former. From the comparison of two Id- Vds characteristics,we conclude that carbon impurity incorporation is responsible for the severe current collapse. The carbon impurity-induced deep traps under negative gate bias stress can capture the channel carriers, which release slowly from these traps under positive bias stress,thus causing the current collapse.展开更多
Gallium arsenide (GaAs) photoconductive semiconductor switches (PCSS's) with a 1.55mm gap spacing trigged by 1553nm femtosecond fiber laser pulse is presented.The switches are biased with 3.33～10.3kV/cm and irrad...Gallium arsenide (GaAs) photoconductive semiconductor switches (PCSS's) with a 1.55mm gap spacing trigged by 1553nm femtosecond fiber laser pulse is presented.The switches are biased with 3.33～10.3kV/cm and irradiated by femtosecond fiber laser operated at a wavelength of 1553nm with pulse width of 200fs and pulse energy of 0.2nJ.The experiments show that,even if the semi-insulating GaAs photoconductive switch operates under the electrical field of 10.3kV/cm,it will be still linear response,and a clear corresponding output electric pulse with the peak voltage of 0.8mV is captured.From the weak photoconductivity on laser intensity,photoabsorption mediated by EL2 deep level defects is suggested,as the primary process for the photoconductivity.展开更多
Zonal disintegration is a typical static phenomenon of deep rock masses. It has been defined as alternating regions of fractured and relatively intact rock mass that appear around or in front of the working stope duri...Zonal disintegration is a typical static phenomenon of deep rock masses. It has been defined as alternating regions of fractured and relatively intact rock mass that appear around or in front of the working stope during excavation of a deep tunnel. Zonal disintegration phenomenon was successfully demonstrated in the laboratory with 3D tests on analogous gypsum models, two circular cracked zones were observed in the test. The linear Mohr-Coulomb yield criterion was used with a constitutive model that showed linear softening and ideal residual plastic to analyze the elasto-plastic field of the enclosing rock mass around a deep tunnel. The results show that tunneling causes a maximum stress zone to appear between an elastic and plastic zone in the surrounding rock. The zonal disintegration phenomenon is analyzed by considering the stress-strain state of the rock mass in the vicinity of the maximum stress zone. Creep instability failure of the rock due to the development of the plastic zone, and transfer of the maximum stress zone into the rock mass, are the cause of zonal disintegration. An analytical criterion for the critical depth at which zonal disintegration can occur is derived. This depth depends mainly on the character and stress concentration coefficient of the rock mass.展开更多
Estimation of support pressure is extremely important to the support system design and the construction safety of tunnels.At present,there are many methods for the estimation of support pressure based on different roc...Estimation of support pressure is extremely important to the support system design and the construction safety of tunnels.At present,there are many methods for the estimation of support pressure based on different rock mass classification systems,such as Q system,GSI system and RMR system.However,various rock mass classification systems are based on different tunnel geologic conditions in various regions.Therefore,each rock mass classification system has a certain regionality.In China,the BQ-Inex(BQ system)has been widely used in the field of rock engineering ever since its development.Unfortunately,there is still no estimation method of support pressure with BQ-index as parameters.Based on the field test data from 54 tunnels in China,a new empirical method considering BQ-Inex,tunnel span and rock weight is proposed to estimate the support pressure using multiple nonlinear regression analysis methods.And then the significance and necessity of support pressure estimation method for the safety of tunnel construction in China is explained through the comparison and analysis with the existing internationally widely used support pressure estimation methods of RMR system,Q system and GSI system.Finally,the empirical method of estimating the support pressure based on BQ-index was applied to designing the support system in the China’s high-speed railway tunnel—Zhengwan high-speed railway and the rationality of this method has been verified through the data of field test.展开更多
The effect of rapid thermal annealing on the optical properties of astrained InAs/InP single quantum well structrure has been investigated in this paper.The luminescence intensity of the quantum well at 8 K was increa...The effect of rapid thermal annealing on the optical properties of astrained InAs/InP single quantum well structrure has been investigated in this paper.The luminescence intensity of the quantum well at 8 K was increased by a factor of 4 and 1.55 meV blue shift of the quantum well photoluminescence peak was observed after annealing at the optimal condition of 700℃ for 5 s. Furthermore,we found that the luminescence efficiency of the deep radiative levels in the samples was also affected by rapid thermal annealing.Our experimental results have demonstrated that Rapid thermal annealing significantly improves the crystalline quality of strained quantum well structures after growth and is an important way for enhancement of the performance of the laser device.展开更多
A Fisher discriminant analysis （FDA） model for the prediction of classification of rockburst in deep-buried long tunnel was established based on the Fisher discriminant theory and the actual characteristics of the p...A Fisher discriminant analysis （FDA） model for the prediction of classification of rockburst in deep-buried long tunnel was established based on the Fisher discriminant theory and the actual characteristics of the project. First, the major factors of rockburst, such as the maximum tangential stress of the cavern wall σθ, uniaxial compressive strength σc, uniaxial tensile strength or, and the elastic energy index of rock Wet, were taken into account in the analysis. Three factors, Stress coefficient σθ/σc, rock brittleness coefficient σc/σt, and elastic energy index Wet, were defined as the criterion indices for rockburst prediction in the proposed model. After training and testing of 12 sets of measured data, the discriminant functions of FDA were solved, and the ratio of misdiscrimina- tion is zero. Moreover, the proposed model was used to predict rockbursts of Qinling tunnel along Xi＇an-Ankang railway. The results show that three forecast results are identical with the actual situation. Therefore, the prediction accuracy of the FDA model is acceptable.展开更多
Automatic signature generation approaches have been widely applied in recent traffic classification.However,they are not suitable for LightWeight Deep Packet Inspection(LW_DPI) since their generated signatures are mat...Automatic signature generation approaches have been widely applied in recent traffic classification.However,they are not suitable for LightWeight Deep Packet Inspection(LW_DPI) since their generated signatures are matched through a search of the entire application data.On the basis of LW_DPI schemes,we present two Hierarchical Clustering(HC) algorithms:HC_TCP and HC_UDP,which can generate byte signatures from TCP and UDP packet payloads respectively.In particular,HC_TCP and HC_ UDP can extract the positions of byte signatures in packet payloads.Further,in order to deal with the case in which byte signatures cannot be derived,we develop an algorithm for generating bit signatures.Compared with the LASER algorithm and Suffix Tree(ST)-based algorithm,the proposed algorithms are better in terms of both classification accuracy and speed.Moreover,the experimental results indicate that,as long as the application-protocol header exists,it is possible to automatically derive reliable and accurate signatures combined with their positions in packet payloads.展开更多
文摘The peculiar photoconduction in semi insulating GaAs photoconductive switch being triggered by 1064nm laser pulse is reported.The gap between two electrodes of the switch is 4mm.When it is triggered by laser pulse with energy of 0 8mJ and the pulse width of 5ns,and operated at biased electric field of 2 0 and 6 0kV/cm,both linear and nonlinear modes of the switch are observed respectively.Whereas the biased electric field adds to 9 5kV/cm,and the triggered laser is in range of 0 5～1 0mJ,the peculiar performed characteristic is observed:the switch gives a linear waveform firstly,and then after a delay time of about 20～250ns,it outputs a nonlinear waveform again.The physical mechanism of this specific phenomenon is associated with the anti site defects of semi insulating GaAs and two step single photon absorption.The delay time between linear waveform and nonlinear waveform is calculated,and the result matches the experiments.
文摘Although outstanding microwave power performance of AlGaN/GaN HEMTs has been reported,drain current collapse is still a problem. In this paper,an experiment was carried out to demonstrate one factor causing the collapse. Two AlGaN/GaN samples were annealed under N2-atmosphere with and without carbon incorporation, and the XPS measurement technique was used to determine that the concentration of carbon impurity in the latter sample was far higher than in the former. From the comparison of two Id- Vds characteristics,we conclude that carbon impurity incorporation is responsible for the severe current collapse. The carbon impurity-induced deep traps under negative gate bias stress can capture the channel carriers, which release slowly from these traps under positive bias stress,thus causing the current collapse.
文摘Gallium arsenide (GaAs) photoconductive semiconductor switches (PCSS's) with a 1.55mm gap spacing trigged by 1553nm femtosecond fiber laser pulse is presented.The switches are biased with 3.33～10.3kV/cm and irradiated by femtosecond fiber laser operated at a wavelength of 1553nm with pulse width of 200fs and pulse energy of 0.2nJ.The experiments show that,even if the semi-insulating GaAs photoconductive switch operates under the electrical field of 10.3kV/cm,it will be still linear response,and a clear corresponding output electric pulse with the peak voltage of 0.8mV is captured.From the weak photoconductivity on laser intensity,photoabsorption mediated by EL2 deep level defects is suggested,as the primary process for the photoconductivity.
基金Projects 50490275 and 50525825 supported by the National Natural Science Foundation of China
文摘Zonal disintegration is a typical static phenomenon of deep rock masses. It has been defined as alternating regions of fractured and relatively intact rock mass that appear around or in front of the working stope during excavation of a deep tunnel. Zonal disintegration phenomenon was successfully demonstrated in the laboratory with 3D tests on analogous gypsum models, two circular cracked zones were observed in the test. The linear Mohr-Coulomb yield criterion was used with a constitutive model that showed linear softening and ideal residual plastic to analyze the elasto-plastic field of the enclosing rock mass around a deep tunnel. The results show that tunneling causes a maximum stress zone to appear between an elastic and plastic zone in the surrounding rock. The zonal disintegration phenomenon is analyzed by considering the stress-strain state of the rock mass in the vicinity of the maximum stress zone. Creep instability failure of the rock due to the development of the plastic zone, and transfer of the maximum stress zone into the rock mass, are the cause of zonal disintegration. An analytical criterion for the critical depth at which zonal disintegration can occur is derived. This depth depends mainly on the character and stress concentration coefficient of the rock mass.
基金Projects(51878567,51878568,51578458)supported by the National Natural Science Foundation of ChinaProjects(2017G007-F,2017G007-H)supported by China Railway Science and Technology Research and Development Plan。
文摘Estimation of support pressure is extremely important to the support system design and the construction safety of tunnels.At present,there are many methods for the estimation of support pressure based on different rock mass classification systems,such as Q system,GSI system and RMR system.However,various rock mass classification systems are based on different tunnel geologic conditions in various regions.Therefore,each rock mass classification system has a certain regionality.In China,the BQ-Inex(BQ system)has been widely used in the field of rock engineering ever since its development.Unfortunately,there is still no estimation method of support pressure with BQ-index as parameters.Based on the field test data from 54 tunnels in China,a new empirical method considering BQ-Inex,tunnel span and rock weight is proposed to estimate the support pressure using multiple nonlinear regression analysis methods.And then the significance and necessity of support pressure estimation method for the safety of tunnel construction in China is explained through the comparison and analysis with the existing internationally widely used support pressure estimation methods of RMR system,Q system and GSI system.Finally,the empirical method of estimating the support pressure based on BQ-index was applied to designing the support system in the China’s high-speed railway tunnel—Zhengwan high-speed railway and the rationality of this method has been verified through the data of field test.
文摘The effect of rapid thermal annealing on the optical properties of astrained InAs/InP single quantum well structrure has been investigated in this paper.The luminescence intensity of the quantum well at 8 K was increased by a factor of 4 and 1.55 meV blue shift of the quantum well photoluminescence peak was observed after annealing at the optimal condition of 700℃ for 5 s. Furthermore,we found that the luminescence efficiency of the deep radiative levels in the samples was also affected by rapid thermal annealing.Our experimental results have demonstrated that Rapid thermal annealing significantly improves the crystalline quality of strained quantum well structures after growth and is an important way for enhancement of the performance of the laser device.
基金Supported by the National 11th Five-Year Science and Technology Supporting Plan of China(2006BAB02A02)Central South University Innovation funded projects (2009ssxt230, 2009ssxt234)
文摘A Fisher discriminant analysis （FDA） model for the prediction of classification of rockburst in deep-buried long tunnel was established based on the Fisher discriminant theory and the actual characteristics of the project. First, the major factors of rockburst, such as the maximum tangential stress of the cavern wall σθ, uniaxial compressive strength σc, uniaxial tensile strength or, and the elastic energy index of rock Wet, were taken into account in the analysis. Three factors, Stress coefficient σθ/σc, rock brittleness coefficient σc/σt, and elastic energy index Wet, were defined as the criterion indices for rockburst prediction in the proposed model. After training and testing of 12 sets of measured data, the discriminant functions of FDA were solved, and the ratio of misdiscrimina- tion is zero. Moreover, the proposed model was used to predict rockbursts of Qinling tunnel along Xi＇an-Ankang railway. The results show that three forecast results are identical with the actual situation. Therefore, the prediction accuracy of the FDA model is acceptable.
基金supported by the National Key Basic Research Program of China (973 Program) under Grant No. 2011CB302605the National High Technical Research and Development Program of China (863 Program) underGrants No. 2010AA012504,No. 2011AA010705+1 种基金the National Natural Science Foundation of China under Grant No. 60903166the National Science and Technology Support Program under Grants No. 2012BAH37B00,No. 2012-BAH37B01
文摘Automatic signature generation approaches have been widely applied in recent traffic classification.However,they are not suitable for LightWeight Deep Packet Inspection(LW_DPI) since their generated signatures are matched through a search of the entire application data.On the basis of LW_DPI schemes,we present two Hierarchical Clustering(HC) algorithms:HC_TCP and HC_UDP,which can generate byte signatures from TCP and UDP packet payloads respectively.In particular,HC_TCP and HC_ UDP can extract the positions of byte signatures in packet payloads.Further,in order to deal with the case in which byte signatures cannot be derived,we develop an algorithm for generating bit signatures.Compared with the LASER algorithm and Suffix Tree(ST)-based algorithm,the proposed algorithms are better in terms of both classification accuracy and speed.Moreover,the experimental results indicate that,as long as the application-protocol header exists,it is possible to automatically derive reliable and accurate signatures combined with their positions in packet payloads.
