现浇混凝土板防渗漏之我见

据实践中遇到的问题 ,提出用防水砼代替普通砼解决顶板砼容易渗漏的问题 ,介绍了防水混凝土是通过调整配合比、控制水灰比、合理砂石级配、适当增加砂率和水泥用量的方法来提高自身密实度和抗渗性的一种砼 ,在工程应用中能达到良好的防水效果。

Shear resistance performance of steel-concrete-steel composite shear wall

For a deeper understanding of the shear resistance performance of the steel-concrete-steel composite shear wall, the main influence factors such as the thicknesses of the steel plates and the concrete, the strength grades of the concrete and the span-depth ratios of the composite wall, which have impacts on the shear resistance performance of the composite shear wail, are analyzed by the numerical simulation method. Meanwhile, the simplified calculation formulae of the initial elastic lateral-resisting stiffness and the shear bearing capacity of the composite shear wall are also proposed. The research shows that with the increase in the thicknesses of the steel plates and the concrete and the increase in the strength grades of the concrete, the shear performance of the shear wall improves obviously; the span-depth ratios of the composite wall have a significant effect on the initial elastic lateral- resisting stiffness, but a small effect on the shear bearing capacity. Comparing the results of the simplified calculation formulae with those of the nonlinear finite element method, it is obvious that the presented formulae are reasonable and meet the real force state of the structure. These conclusions can serve as a preliminary design reference for the steel-concrete- steel composite shear wall.

Interfacial behaviors of epoxy asphalt surfacing on steel decks

A model for predicting the interface behavior of epoxy asphalt and steel composite beam under negative bending is developed incorporating partial interaction theory. Interfacial slips between the steel deck and the epoxy asphalt surfacing are included in the model with a new parameter of membrane stiffness. A series of analytical equations based on this model are derived to calculate slip and strain at the interface. Also, a numerical procedure for calculating the load responses of simply supported composite beams with concentrated force at the mid-span is established and verified with two samples. Characters of slip and strain at the interface, sensitivities of tensile stress and interface shear stress with material parameters are studied. It can be concluded that interfacial effects decrease the bending stiffness of the composite; hard and stiff bonding material is better for asphalt surfacing layer working at normal to low temperatures, and the damage of the asphalt surfacing layer will be accelerated with the damage accumulation of the bonding coat.

湘潭锰矿急倾斜薄矿体充填采矿方法改进的探讨

本文简要指出湘潭锰矿开采急倾斜薄矿体时应用上向水平分层充填采矿法存在的问题，探讨了在该矿条件下改用下向分层水砂充填法的合理性，并对该应用锚杆和混凝土板联合支护系统进行了分析，分析结果表明，采用１００～１５０＆＃混凝土，混凝土板厚度为２５０～３００ｍｍ将可满足生产要求。

Closed-form solution for shear lag effects of steel-concrete composite box beams considering shear deformation and slip

Based on the consideration of longitudinal warp caused by shear lag effects on concrete slabs and bottom plates of steel beams,shear deformation of steel beams and interface slip between steel beams and concrete slabs,the governing differential equations and boundary conditions of the steel-concrete composite box beams under lateral loading were derived using energy-variational method.The closed-form solutions for stress,deflection and slip of box beams under lateral loading were obtained,and the comparison of the analytical results and the experimental results for steel-concrete composite box beams under concentrated loading or uniform loading verifies the closed-form solution.The investigation of the parameters of load effects on composite box beams shows that:1) Slip stiffness has considerable impact on mid-span deflection and end slip when it is comparatively small;the mid-span deflection and end slip decrease significantly with the increase of slip stiffness,but when the slip stiffness reaches a certain value,its impact on mid-span deflection and end slip decreases to be negligible.2) The shear deformation has certain influence on mid-span deflection,and the larger the load is,the greater the influence is.3) The impact of shear deformation on end slip can be neglected.4) The strain of bottom plate of steel beam decreases with the increase of slip stiffness,while the shear lag effect becomes more significant.

Experimental research on ultimate bearing capacity of grouted-round-steel-tube N-joint

As an important structural member in self-supporting concrete floor during construction,encased steel truss-concrete composite beam has brilliant prospect in outer-jacketing structures for adding stories or mega frame structures.Compared with encased angle truss,encased round steel tube truss can facilitate layout of itself in column and facilitate layout and anchorage of prestressed reinforcement placed horizontally.N-joint is wildly used in encased steel truss.For cave-in failure easily occurs in hollow steel-tube joint,the idea that the chord is grouted to increase cave-in bearing capacity of hollow tube is proposed.Test results of 8 grouted-round-steel-tube N-joints from the beginning of loading to failure are reported.Mechanical property and failure mode of this kind of truss joint are analyzed,and the formulas of ultimate bearing capacity of the joint corresponding to different failure modes are established.All these can provide basic data for spreading encased steel truss-concrete composite beam.

Improved methods for decreasing stresses of concrete slab of large-span through tied-arch composite bridge

Mechanical behavior of concrete slab of large-span through tied-arch composite bridge was investigated by finite element analysis (FEA). Improved methods to decrease concrete stresses were discussed based on comparisons of different deck schemes, construction sequences and measures, and ratios of reinforcement. The results show that the mechanical behavior of concrete slab gets worse with the increase of composite regions between steel beams and concrete slab. The deck scheme with the minimum composite region is recommended on condition that both strength and stiffness of the bridge meet design demands under service loads. Adopting in-situ-place construction method, concrete is suggested to be cast after removing the full-supported frameworks under the bridge. Thus, the axial tensile force of concrete slab caused by the first stage dead load is eliminated. Preloading the bridge before concrete casting and removing the load after the concrete reaching its design strength, the stresses of concrete slab caused by the second stage dead load and live load are further reduced or even eliminated. At last, with a high ratio of reinforcement more than 3%, the concrete stresses decrease obviously.

Pressure-impulse diagram with multiple failure modes of one-way reinforced concrete slab under blast loading using SDOF method

Two loosely coupled single degree of freedom (SDOF) systems were used to model the flexural and direct shear responses of one-way reinforced concrete slabs subjected to explosive loading. Blast test results show that the SDOF systems are accurate in predicting the failure mode of the slab under blast loads by incorporating the effects of the strain rate effect caused by rapid load application. Based on different damage criteria, pressure-impulse (P-I) diagrams of the two failure modes were analyzed with the SDOF systems. The effects of span length, concrete strength, and reinforcement ratio of the slab on the P-I diagram were also investigated. Results indicate that a slab tends to fail in direct shear mode when it is of a smaller span length and tends to fail in flexure mode when it is of a larger span length. With the increase of the concrete strength or reinforced ratio, both the flexure and shear capacity increase. Based on numerical results, a simplified method and a semi analytical equation for deriving the P-I diagram are proposed for different failure modes and damage levels.

Technical Progress on Researches for the Safety of High Concrete-Faced Rockfill Dams

The concrete-faced rockfill dam(CFRD) is an important dam type in the selection of high dams to be constructed in Western China,owing to its direct utilization of local materials,good adaptability,and distinct economic advantages.Over the past decades,China has gained successful experience in the construction of 200 m CFRDs,providing the necessary technical accumulation for the development of 250–300 m ultra-high CFRDs.This paper summarizes these successful experiences and analyzes the problems of a number of major 200 m CFRDs around the world.In addition,it discusses the key technologies and latest research progress regarding safety in the construction of 250–300 m ultra-high CFRDs,and suggests focuses and general ideas for future research.

Retrofitting of RC Slabs Against Explosive Loads

With the increase of terrorist bomb attacks on buildings, there is a need to develop advanced retrofitting techniques to strengthen structures against blast loads. Currently, several guidelines including an Australian version for retrofitting reinforced concrete (RC) structures are available for the design of retrofitting systems against seismic and monotonic loads using steel or fibre reinforced polymer (FRP) plates that can be either adhesively bonded to the surface or near surface mounted to the concrete cover. However, none of these guidelines provide advice suitable for retrofitting structures subjected to blast loads. In this paper, numerical models are used to simulate the performance of retrofitted RC slabs subjected to blast loads. Airblast pressure distributions on the surface of the slabs estimated in a previous study are used as input in the analysis. A material damage model developed previously for concrete and an elastoplastic model for steel bars are employed in this research for modelling reinforced concrete behaviour due to explosive loads. The material models and blast loading are coded into a finite element computer program LS-DYNA3D to do the analysis. With the numerical model, parametric studies are conducted to investigate RC slabs retrofitted by either externally bonded or near-surface mounted plates or GFRP sheets subjected to blast loads. Discussion is made on the effectiveness of the retrofitting system for RC slabs against blast loads.

Theoretical Calculation and Analysis of Slip and Deformation for Concrete Sandwich Panels

Slip and deformation of concrete sandwich panels under uniformly distributed loads is concerned. The effect of slip on the deformation of concrete sandwich panels are studied,and the analytical expressions of slip and deformation for concrete sandwich panels is obtained. These formulae can describe the slip distribution and account for its effect on deformation. In order to restrict the bound of formula, the formula of crack moment is obtained. The results of theoretical calculation are compared with those of tests and finite element methods. The comparison shows that the results of theoretical calculation are in accord with those of tests and finite element methods. So the theoretical calculation can be used to calculate slip and deformation of concrete sandwich panels in practical projects.

Seismic Enhancement of Existing Buildings by Means of Fiber Reinforced Concrete Diaphragms

Floor diaphragms may provide an effective solution for reducing the seismic vulnerability of masonry buildings. Unfortunately, diaphragms are usually not present in historical building with wooden floors but often they are non present even in old R/C buildings where floors were made without shear reinforcement. A possible strengthening technique could be based on the application of a thin concrete plate reintbrced with a welded mesh. In order to reduce the thickness of the plate, some suitable solutions may be obtained by using Fiber Reinforced Concrete （FRC） since the minimum concrete cover is no longer required because the reinforcement （fibers） is spread all over the concrete matrix. The adoption of FRC floor diaphragms is proposed and discussed in this paper; the early results from a preliminary numerical study are analyzed in order to asses the feasibility of this new strengthening technique and better organize an experimental program that is currently in progress.

Fuzzy Earthwork Dynamic Allocation and Optimization for Construction of High Concrete Face Rockfill Dam

Due to the complexity of earthwork allocation system for the construction of high concrete face rockfill dam,traditional allocation and planning are not able to function properly in the construction process with strong randomness.In this paper,the working mechanism of earthwork dynamic allocation system is analyzed comprehensively and a solution to fuzzy earthwork dynamic allocation is proposed on the basis of uncertain factors in the earthwork allocation of a hydropower project.Under the premise of actual situation and the experience of the construction site,an all-coefficient-fuzzy linear programming mathematical model with fuzzy parameters and constraints for earthwork allocation is established according to the structure unit weighted ranking criteria.In this way,the deficiency of certain allocation model can be overcome.The application results indicate that the proposed method is more rational compared with traditional earthwork allocation.

Flexural behaviour of SFRRAC two-way composite slab with different shapes

To promote the application of green renewable materials in concrete composite slabs(CCSs)and study the flexural behavior of CCSs with different shapes,the bending performances of three CCSs with a SFRRAC base plate,one cast-in-site concrete slab of ordinary concrete and one CCS of ordinary concrete by steel bar truss(as recommended in the technical specification for precast concrete structures in Chinese)were compared through experiments.The carrying capacity,flexural behaviour and bi-directional mechanical properties of the specimens were systematically analyzed from the failure modes,load-deflection curves,load-bar strain curves,load-slip curves and crack distributions.Results show that the bending failure process of CCSs with a SFRRAC base plate is similar to that of the cast-in-site concrete slab of ordinary concrete and CCS of ordinary concrete by steel bar truss,as all of them went through the plastic phase,elastic plastic phase and failure phase with fully developed cracks and deflection.No sudden breakage or horizontal cracking of the connecting interface between the base plate and concrete topping was observed.The shape of the base plate has a major impact on the bearing capacity of the CCS with the SFRRAC base plate.When calculating the ultimate bearing capacity with the plastic yield line theory,the influence of the base plate shape on the plastic yield line position should be taken into account.

BIM-based construction technologies for precast foamed lightweight concrete wallboards

To promote the visualisation and informatisation of the construction process of precast foamed lightweight concrete wallboards(PFLCWs),from the analysis of the construction requirements of PFLCWs,three key construction technologies based on building information modelling(BIM),namely,parameterised modelling for the PFLCW layout design,drawing generation to draw the PFLCW layout and quantity statistics for extracting PFLCW quantities,are proposed.Then,a reinforced concrete(RC)frame infilled with PFLCW is considered the test model to verify the feasibility of the aforementioned technologies.The results show that PFLCW layout design can be accomplished rapidly and visually using parameterised modelling technology.The PFLCW layout diagram can be generated directly using drawing generation technology.The proposed quantity statistics technology enables the automatic export of PFLCW bills of quantities.The built parameterised model helps construction workers rapidly and intuitively understand the specific layout details of PFLCWs.Moreover,the generated layout drawing and the bills of quantities based on the parameterised model can guide the production and on-site installation of PFLCWs.The research conclusions can serve as a practical guide and technical support for PFLCW engineering applications.

Bending Resistance of Steel Plate-Reinforced Concrete Beam

The formulas for calculating bending-resistant capacity of a steel plate-reinforced concrete composite beam are derived. To validate the formulas, experiments of the composite beam under three-point bending are carried out. Calculated results based on the formulas are in good agreement with experimental results.

Finite Element Analysis of Reinforced Concrete Plate Impacted by Block

A new concept of structurally dissipating rock-shed (SDR) was developed by the lab of Tonello IC and LOCIE-ESIGEC (France). To decide the dimension of the plate used in SDR, an ANSYS model which could simulate the impact of rock in the centre of the plate was established by Fabien Delhomme. By using this model, some finite element analyses are carried out in the present paper. Firstly, a plate impacted by a block is numerically simulated, the numerical results obtained from different mesh sizes are compared and the accuracy of the finite element model is verified. Then, the dynamic response of the plate impacted at the boundary and in the medium part is computed. By analyzing the stress in rebar, the most dangerous region of impact of plate was found. For a rectangular plate, the most dangerous region is at the corner of the plate when a block drops in. Finally, the whole deformation process of the plate under dropping block was simulated and a simplified definition (effect zone) to describe the deformation process in different positions of plate was given. From this study, it is found that the impact only affects heavily within the effect zone.

Strengthening of Concrete Box Girder Bridges under Close-in Detonations

The response of a bridge superstructure under blast loading might depend largely on the extent of the local damage experienced due to close-in explosion threats. This paper investigates the local and structural response of box girder bridge decks strengthened using CFRP （carbon fiber reinforced polymers） under close-in detonations. Due to the lack of experimental research on this topic, the study is conducted using the explicit finite element computer program LS-DY-NA. The numerical study will be verified using the results of strengthened reinforced concrete slabs under field detonations. The blast load was assumed to be detonated above the bridge deck. The key parameters investigated are the charge size, and the strengthening location on the deck. This paper will present the results of this investigation and provides recommendations for predicting the local damage level based on the CFRP strengthening design under blast threat.

Mechanical response of continuously reinforced concrete pavement on foam concrete interlayer for two-way curved arch bridge

In order to research the mechanical response of continuously reinforced concrete pavement on foam concrete interlayer for a two-way curved arch bridge, the elliptical vehicle load is translated into the rectangular load based on the equivalence method. Then, a three-dimensional finite element model of the whole bridge is established. The reliability of the model is verified. Additionally, the mechanical response of continuously reinforced concrete pavement under vehicle loading is analyzed. Finally, the most unfavorable loading conditions of tensile stress, shear stress and vertical displacement are determined. The results show that the most unfavorable loading condition of tensile stress, which is at the bottom of continuously reinforced concrete pavement on the two-way curved arch bridge, is changed compared with that on homogeneous foundation. The most unfavorable loading condition of shear stress at the top is also changed. However, the most unfavorable loading condition of vertical displacement remains unchanged. The tensile stress at the bottom of about 1/4 span of the longitudinal joint, the shear stress at the top of intersection of transverse and longitudinal joint, together with the vertical displacement at the central part of longitudinal joint, are taken as design indices during the structural design of continuously reinforced concrete pavement on the two-way curved arch bridge. The results are helpful for the design of continuously reinforced concrete pavement on unequal- thickness base for the two-way curved arch bridge.