悬浇预应力连续刚构桥设计应注意的问题

主要针对中大跨径悬浇变截面预应力混凝土连续刚构桥在纵向受力分析时所要考虑和经常碰到的如结构上部尺寸的确定,下部结构形式,温度影响因素及悬臂施工不平衡荷载等一些问题,进行分析探讨,为类似的施工设计提供参考。

给水管道损坏的主要原因和对策

本文通过管道破坏的资料和实例分析研究，指出了给水管道破坏的主要原因是管材及其接口方法、温变应力以及水锤的影响，并提出了对策。

浅析给水管道损坏的主要原因及其对策

通过管道破坏的资料和实例分析研究,指出了给水管道破坏的主要原因是管材及其接口方法,温变应力以及水锤的影响,并提出解决对策。

Prediction of flow stress of Mg-Nd-Zn-Zr alloy during hot compression

Isothermal hot compression tests were carried out on Mg-3.0Nd-0.2Zn-0.4Zr （mass fraction, %, NZ30K） alloy using a Gleeble-3500 thermo-simulation machine at temperatures ranging from 350 to 500 ℃and strain rates from 0.001 to 1 s^-1. A correction of flow stress for deformation heating at a high strain rate was carried out. Based on the corrected data for deformation heating, a hyperbolic sine constitutive equation was established. The constants in the constitutive equation of the hyperbolic sine form were determined as a function of strain. The flow stresses predicted by the developed equation agree well with the experimental results, which confirms that the developed constitutive equations can be used to predict the flow stress of NZ30K alloy during hot deformation.

Microstructure and properties of WE93 alloy

The microstructure of WE93 alloy in different states and the mechanical properties at room temperature were investigated, and the creep behavior of the extruded and aged alloy at 200 ℃and at stress of 100, 125 and 150 MPa was also discussed. The result shows that the microstructure of as-cast WE93 alloy consists of α-Mg, Mg 12 （MM） and Mg 24 Y 5 with an average grain size of 45 μm. After being homogenized at 535 ℃for 18 h, the Mg 24 Y 5 phase is dissolved completely and there is only Mg 12 （MM） phase left around the grain boundaries. The grains do not grow up as prolonging the homogenization time. The extruded alloy has better mechanical properties than the as-cast alloy, especially the elongation increases to 12.5%. The extruded and aged alloy exhibits the highest yield strength and ultimate tensile strength of 315 and 385 MPa, respectively, however, the elongation decreases to 6.5%. The extruded and aged alloy exhibits good creep resistance at 200 ℃and at stress of 100 150 MPa. The creep stress exponent n is 2.97, suggesting that grain boundary sliding plays a dominant role at the corresponding temperature and applied stresses.

城市给水管道的常见事故及其防治

为了保证市民的正常生活，城市的进一步发展，作为城市的血脉——供水系统的正常运转，显得尤为重要。本文通过对管道破坏的资料和实例分析研究，指出了给水管道破坏的主要原因是管材及其接1：1方法，温变应力以及水锤的影响，并提出解决对策。

35t/h炉面式减温器冷却水管裂纹原因浅析

对面式减温器冷却水管产生裂纹原因的分析表明,由于水质含氧和Cl^-离子过高,造成腐蚀,同时由于操作不当,产生温变应力,致使冷却水管腐蚀疲劳产生裂纹。

Flow behavior and microstructure evolution of 6A82 aluminium alloy with high copper content during hot compression deformation at elevated temperatures

The flow behavior and microstructure evolution of 6A82 aluminum alloy (Al?Mg?Si?Cu) with high copper content were studied on a Gleeble?1500 system by isothermal hot compression test in the temperature range from 320 to 530 °C and the strain rate range from 0.001 to 10 s?1. The results reveal that the flow stress of the alloy exhibits a continuous flow softening behavior at low temperatures of 320?390 °C, whereas it reaches steady state at high temperatures (≥460°C), which are influenced greatly by the Zener?Hollomon parameter (Z) in the hyperbolic sine with the hot deformation activation energy of 325.12 kJ/mol. Microstructure characterizations show that prominent dynamic recrystallization and coarsening of dynamic precipitation may be responsible for the continuous flow softening behavior. Due to deformation heating at high strain rates (≥1 s?1), dynamic recrystallization is more prominent in the specimen deformed at 530 °C and 10 s?1 than in the specimen deformed at 460 °C and 0.1 s?1 even though they have very close lnZ values.

Hot deformation behavior and constitutive relationship of Q420qE steel

Isothermal compression tests at temperatures from 1 273 to l 423 K and strain rates from 0.1 to 10 s-q were carried out to investigate the flow behaviors of Q420qE steel. Stress-strain data collected from the tests were employed to establish the constitutive equation, in which the influence of strain was incorporated by considering the effect of strain on material constants Q, n, a, and lnA. The results show that the flow stress curves are dependent on the strain, strain rate and deformation temperature. They display typical dynamic recrystallization behavior and consist of three stages, i.e., hardening stage, softening stage and steady stage. The flow stress decreases with increasing the deformation temperature and decreasing the strain rate. In addition, the flow stress data predicted by the proposed constitutive model agree well with the corresponding experimental results, and the correlation coefficient and the average absolute relative error between them are 0.990 3 and 3.686%, respectively.

Behavior of concrete and concrete-filled circular steel tubular stub columns at constant high temperatures

Based on reanalyzing test results of uniaxial compressive behavior of concrete at constant high temperatures in China, with the compressive cube strength of concrete from 20 to 80 MPa, unified formulas for uniaxial compressive strength, elastic modulus, strain at peak uniaxial compression and mathematical expression for unaxial compressive stress-strain relations for the concrete at constant high temperatures were studied. Furthermore, the axial stress-axial strain relations between laterally confined concrete under axial compression and multiaxial stress-strain relations for steel at constant high temperatures were studied. Finally, based on continuum mechanics, the mechanics model for concentric cylinders of circular steel tube with concrete core of entire section loaded at constant high temperatures was established. Applying elasto-plastic analysis method, a FORTRAN program was developed, and the concrete-filled circular steel tubular （CFST） stub colunms at constant high temperatures were analyzed. The analysis results are in agreement with the experiment ones from references.

Effect of temperature and stress on molecular structure and carbon monoxide generation of lignite from Kailuan mining area

In order to analyze the origin of carbon monoxide(CO) in coal seams, stress–strain experiments under temperature of 50, 150 and 250 °C were conducted using lignite from Kailuan mining area. Fourier transform infrared spectroscopy and elemental analysis were carried out before and after deformation of the samples. The results indicated that CO generated at 150 and 250 °C; the gas component was mostly oxygen(O_2), with small amount of carbon dioxide(CO_2), methane(CH_4) and hydrogen(H_2). At 50 °C, O_2 and a little CO_2 were observed and no CO was found. The carbon content of the coal samples increased slightly after deformation, and the oxygen content, H/C ratio, and O/C ratio decreased. The molecular structure of coal displayed different evolution characteristics at various temperatures. At 50 and 150 °C, the falling off of side chains, broken of ether bond and directional realignment of the aliphatic chains resulting in the formation of long chains were the main performance of coal molecular structure evolution. While at 250 °C, the side chains fell off and short chains formed. Furthermore, at both 150 and 250 °C, condensed degree of aromatic ring increased. Under the action of temperature and pressure, CO forms in two ways.The first is that ether bond breaks, oxygen and carbon atoms combine together and forms CO, or O_2 forming in the broken of ether–oxygen bond leads to the oxidation of free radicals and resulting in the formation of CO. And the second is that CO derives from falling off of C=O group.

Dynamic modeling of twin roll casting AZ41 magnesium alloy during hot compression processing

A dynamic material model of Mg-4.51Al-1.19Zn-0.5Mn-0.5Ca(AZ41,mass fraction,%)magnesium alloy was put forward.The results show that the dynamic material model can characterize the deformation behavior and microstructure evolution and describe the relations among flow stress,strain,strain rates and deformation temperatures.Statistical analysis shows the validity of the proposed model.The model predicts that lower deformation temperature and higher strain rate cause the sharp strain hardening. Meanwhile,the flow stress curve turns into a steady state at high temperature and lower strain rate.The moderate temperature of 350 ℃and strain rate of 0.01 s-1 are appropriate to this alloy.

Residual stress and welding distortion of Al/steel butt joint by arc-assisted laser welding-brazing

The thermo-elastic.plastic finite element method(FEM)is used to simulate the thermo-mechanical behavior of Al/steel tungsten inert gas(TIG)arc-assisted laser welding-brazing(A-LWB)butt joint.The influence of material nonlinearity,geometrical nonlinearity and work hardening on the welding process is studied,and the differences in the welding temperature field,residual stress and welding distortion by A-LWB and by single laser welding-brazing(SLWB)are analyzed.The results show that the thermal cycle,residual stress distribution and welding distortion by the numerical simulation are in good agreement with the measured data by experiments,which verifies the effectiveness of FEM.Compared with the SLWB,A-LWB can make the high-temperature distribution zone of weld in width direction wider,decrease the transverse tensile stress in the weld and reduce the distribution range of longitudinal tensile stress.And the welding deformation also decreases to some extent.

Properties of failure mode and thermal damage for limestone at high temperature

The mechanical properties of limestone such as the stress-strain curve, the variable characteristics of peak strength and the modulus of elasticity of limestone were studied under the action of temperatures ranging from room temperature to 800 °C.Our results show that:1) the temperature has not clear effect on the mechanical properties of limestone from room temperature to 600 °C.However, the mechanical properties of limestone deteriorate rapidly when the temperature is above 600 °C.In this case, the peak stress and modulus of elasticity decrease rapidly.When the temperature reaches 800 °C, the entire process, showing the stress-strain curve is displayed indicating an obvious state of plastic-deformation;2) the failure mode of limestone shows the breakdown of tensile strength from room temperature to 600 °C, as well as the compress shearing damage over 600 °C;3) combining our test results with the concept of thermal damage, a thermal damage equation was derived.

Tensile properties of as-deformed 2A50 aluminum alloy in semi-solid state

Tensile properties of as-deformed 2A50 aluminum alloy were investigated in the high temperature solid and semi-solid states. The results show that temperature has almost no effect on the maximum tensile stress between 500 ℃ and 530 ℃, and the maximum tensile stress decreases rapidly when the temperature is above 532 ℃. The ductility decreases with increasing temperature and has an obvious fall when the temperature is above solidus temperature. This alloy almost has no ductility above 537 ℃, and cannot sustain tensile stress above 550℃. A brittle temperature range in which this alloy is prone to form microcracks was derived. The relation between microstructure, fraction solid and tensile properties were also investigated by examining the metallograph and fracture surface morphology of tested specimens, which could provide reference for forecasting the microcracks in this alloy occurring in semi-solid processing.

Effects of strain rates on mechanical properties of limestone under high temperature

The experimental tests for limestone specimens at 700 °C in uniaxial compression were carried out to inves- tigate the mechanical effects of loading rates on limestone by using a MTS810 rock mechanics servo- controlled testing system considering the loading rate as a variable. The mechanical properties of limestone such as the stress-strain curve, variable characteristics of peak strength and the modulus of elasticity of limestone were studied under the strain rates ranging from 1.1 10à5 to 1.1 10à1 sà1. (1) Sharp decreases were shown for the peak strength and elastic modulus of limestone from 1.1 10à5 to 1.1 10à4 sà1 at 700 °C as well as a downward trend was shown from 1.1 10à4 to 1.1 10à1 sà1 with the rise of the strain rate. (2) The peak strain increased from 1.1 10à5 to 1.1 10à4 sà1, however, there was no obvious changes shown for the peak strain of limestone from 1.1 10à4 to 1.1 10à1 sà1. These results can provide valuable references for the rock blasting effect and design of mine.

Effects of loading rate and peak load on nanoindentation creep behavior of DD407 Ni-base single crystal superalloy

Nanoindentation experiments were conducted under loading rates of 500–6000μN/s and applied peak loads of 4000-12000μN to measure the creep behavior of DD407 Ni-base single crystal superalloy at room temperature.Experimental results demonstrated that DD407 Ni-base single crystal superalloy had a good creep resistance,but its creep properties were sensitive to the loading rate and peak load.The fitting creep parameters significantly increased with increasing loading rate and peak load based on the Findley’s model,and the corresponding creep mechanism was governed by dislocation based on the calculation of creep stress exponent.During nanoindentation creep tests,it was found that the hardness and reduced modulus decreased with increasing the loading rate and peak load,and through a dimensionless analysis,it was also noted that the effect of the dimensionless loading rate was stronger than that of dimensionless peak load on the creep properties.

Macroscopic Frost Heave Model Based on Segregation Potential Theory

A macroscopic frost heave model with more clear parameters was established. Based on a porosity rate frost heave model and segregation potential theory, a porosity rate function was deduced and introduced into the stress-strain relationship. Numerical simulation was conducted and verified by frost heave tests. Results show that the porosity rate within the frozen fringe is proportional to the square of temperature gradient and current porosity, and is also proportional to the exponential function of applied pressure. The relative errors between the calculated and measured results of frost depth and frost heave are within 3% and 15% respectively, demonstrating that the temperature gradient, applied pressure and current porosity are the main influencing factors, while temperature is just the constraint of frozen fringe. The improved model have meaningful and accessible parameters, which can be used in engineering with good accuracy.

Response of North Pacific and North Atlantic decadal variability to weak global warming

The Pacific Decadal Oscillation （PDO） and the Atlantic Multidecadal Variability （AMV） are the two dominant low-frequency modes in the climate system. This research focused on the response of these two modes under weak global warming. Observational data were derived from the Hadley Center Sea Ice and Sea Surface Temperature dataset （HadISST） and coupled model outputs from the Coupled Model Intercomparison Project Phase 5 （CMIP5）. Changes in PDO and AMV were examined using four models （bcc-csml-1, CCSM4, IPSL-CM5A-LR, and MPI- ESM-LR） with long weak global warming scenarios （RCP2.6）. These models captured the two low-frequency modes in both pre-industrial run and RCP2.6 run. Under weak global warming, the time scales of PDO and AMV significantly decreased while the amplitude only slightly decreased. Interestingly, the standard deviation of the North Pacific sea surface temperature anomaly （SSTA） decreased only in decadal time scale, and that of the North Atlantic SSTA decreased both in interannual and decadal time scales. The coupled system consists of a slow ocean component, which has a decadal time scale, and a fast atmospheric component, which is calculated by subtracting the decadal from the total. Results suggest that under global warming, PDO change is dominated by ocean dynamics, and AMV change is dominated by ocean dynamics and stochastic atmosphere forcing.

New approach for modeling flow stress of aluminum alloy 6A10 considering temperature variation

The flow stress behavior of aluminum alloy 6A10 was studied by the hot compression tests at temperatures from 350℃ to 550 ℃ and strain rates from 0.1 s^-1 to 10 s^-1 with Gleeble-1500 thermo-mechanical simulator. The result demonstrates that the temperatures of specimen differ from initial ones affected by deformation conditions, and that the softening mechanism is dynamic recovery. A new approach was proposed to analyze the flow stress character directly from actual stress, strain, temperature and strain rate data, without performing any previous flow stress correction caused by temperature variation. Comparisons between the experimental and predicted results confirm that the established flow stress model can give reasonable estimation, indicating that the mentioned approach can be used in flow stress model analysis of the materials that undergo only dynamic recovery based on the data obtained under variable deformation temperature.