有限差分法确定石墨电极中的温度分布

采用有限差分的方法，根据实测处于正常工作状态时电极中的温度分布、热传导的基本方程以及有关边界条件建立的石墨电极从炉内撤出不同时间后电极中的温度场。结果表明，当电极从炉内撤出以后，电极中的温度分布将发生显著的变化，电极表层和端都附近的温度梯度在刚撤出后迅速增大，特别是表层温度梯度远大于正常工况下的温度梯度。

Electromagnetic simulation and experimental analysis of microwave heaters for asphalt pavements

In order to study the thermoelectric efficiency of microwave heating and reproduction of asphalt pavements and the uniformity of reproduction temperature distribution, a waveguide excitation cavity is designed and applied to the structural design of a microwave heater. The structural sizes of the incentive cavities are determined based on the waveguide transmission line theory. Using IE3D software, electromagnetic simulations are respectively carried out in four different situations, including the distances between the magnetron probes （antennas） and a short-circuit board, different horn electric lengths and aperture sizes, different dielectric properties of the asphalt mixture, and the distances between the asphalt surface and the mouth cavity. The results show that, when the distance between the magnetron probe and the short-circuit board is 32.5 ram, it is the best installation site; reduction of aerial length is the main factor in improving the heating uniformity. When the aggregate is limestone, the best heating effect can be produced. Maximum radiation efficiency can be realized by adjusting the space between the heater radiation port and the asphalt pavement. The experimental results of asphalt mixture heating in four different situations have a substantial agreement with the simulation results, which confirms that the developed microwave heater can achieve better impedance matching, thus improving the quality and efficiency of heating regeneration.

Transient temperature field of a friction pair in a HVD device of a belt conveyor

To show the distribution of a temperature field on a steel disk and to prolong the service life of a friction pair in a Hy-dro-Viscous Drive (HVD) device, a theoretical model of a transient temperature field was established, based on the theory of heat conduction. This theoretical model was solved using a finite element method. The results show that the surface temperature of the steel disk does not increase consistently as a function of the radius; the highest temperature appears short of the maximum radius. The relationship between the surface temperature and the mixed friction time is exponential. With a friction time of 15 s, the tem-perature reached 465.9 °C. Simultaneously, the internal thermal stress is larger than the yield stress of the material, causing a warping deformation of the steel disk. The largest axial deformation is 0.32 mm. The results of the experiment suggest that the de-formation is the same as that obtained from numerical simulation. Therefore, deformation of the steel disk must be considered dur-ing the study of the characteristics of a HVD.

Computer Simulation on Metallic Card Clothing Garnett Wire Teeth's Temperature Field & Structure Field in the Process of Quenching Treatment

The quenching process of garnett wire teeth of metallic card clothing heated by flame was researched by use of 3-D finite element method and the equation of boundary condition was established by making use of a model of artificial neural network. The transient temperature field, phase transformation in the heating process, the quenching microstructures and the hardness distribution on quenched garnett wire teeth of metallic card clothing were simulated. The result shows that the maximum error of the hardness between the simulative value and the actual measuring value is 8.0% on only one testing point and errors are all less than 3.0% on other testing points.

Numerical simulation of hot stamping of side impact beam

Ls-DYNA software is adopted to conduct research of numerical simulation on hot stamping of side impact beam to calculate the temperature field distribution, stress field distribution, forming limit diagram （FLD） figure, etc. in the course of hot stamping so as to predict and analyze the formability of parts. ProCAST software is employed to conduct research of numerical simulation on solid quenching course concerning hot stamping to calculate temperature field distri- bution of tools and component of muhiple stamping cycles. The results obtained from numerical simulation can provide significant reference value to hot stamping part design, formability predication and tools cooling system design.

Temperature field distribution of burnt surrounding rock in UCG stope

In order to study temperature field distribution in burnt surrounding rock and to determine ranges of burnt surrounding rock, coal-wall coking cycle and heat influence in the underground coal gasification(UCG) stope, based on the Laplace transform and inversion formula, we studied the temperature analytical solution of one-dimensional unsteady heat conduction for multi-layer overlying strata under the first and the forth kinds of boundary conditions, and we also carried out a numerical simulation of twodimensional unsteady heat conduction by the COMSOL multiphysics. The results show that when the boundary temperature of surrounding rock has a linear decrease because of a directional movement of heat source in the UCG flame working face, the temperature in surrounding rock increases first and then decreases with time, the peak of temperature curve decreases gradually and its position moves inside surrounding rock from the boundary. In the surrounding rock of UCG stope, there is an envelope curve of temperature curve clusters. We analyzed the influence of thermophysical parameters on envelope curves and put forward to take envelope curve as the calculation basis for ranges of burnt surrounding rock, coal-wall coking cycle and heat influence. Finally, the concrete numerical values are given by determining those judgement standards and temperature thresholds, which basically tally with the field geophysical prospecting results.

Study on visualization simulation of temperature distributions in surrounding rock of tunnels in a deep mine

Based on the mathematical model for rock temperature distribution in a geo-thermal field,the properties of rock temperature distribution in geothermal field for fourkinds of surrounding rock cross-sections of tunnels in a deep mine were simulated by us-ing finite element method.It is shown that the relationship for rock temperature distributionvaried with the geothermal parameters,time and space.Namely, 2-dimensionaltime-dependent isograms clearly showed the process for rock temperature variation anddistribution in a geothermal field which has been redisplayed with visualization numericalsimulation.

Pulse modulated microwave and infrared thermography for superficial hyperthermia

A 3D temperature field distribution of biological tissue for superficial hyperthermia using a pulse modulated microwave （PMMW） was presented. A 3D sliced homogeneous phantom was radiated by the PMMW and an infrared thermal imager was applied to image temperature distribution throughout the phantom. The period of the PMMW is 3 s and the output power is 35 W. The temperature rises by at least 3 ℃ in the phantom when the duty cycle varies from 1/3, 1/2, 2/3 to 1 （denoted by scenarios 1-4）. Both the accumulative temperature-volume histogram and the relative depth-area ratio histogram show that the maximum temperature rise （MTR） is 6.6 and 8 ℃ in scenarios 2 and 3, and they are superior to scenarios 1 and 4. Furthermore, the PMMW can control temperature field distribution of biological tissue. It provides both preliminary basis for thermal volume control and new technology for temperature control and monitor in superficial hyperthermia.

Study on application and numerical simulation of the airflow temperature distribution rule in drifting tunnel

According to the law of conservation in the state of turbulent flow, the differential equation describing the airflow temperature distribution in drifting tunnel is derived, By theoretical analysis and field measurement of the airflow and thermal process in mine, theoretical analysis and systematic flow are developed. By PHONENICS program, the numerical simulation is processed, and the changing rule of airflow temperature with various parameters in drifting tunnel is derived. The airflow temperature in drifting tunnel decreases as the airflow velocity increases in a way of negative power exponent, and elevates linearly as the temperature of the incoming airflow elevates.

Thermal analysis of high speed permanent magnetic generator

High-speed permanent magnetic generators (HSPMG) are common and important power generation equipments used in distributed generation systems. A 100 kW level HSPMG is investigated in this paper, and it is fluid-thermal coupling analyzed. The transient 2D electromagnetic field while machine is under rated operating is analyzed by using the time-stepping FEM, from which the electromagnetic performances and the loss distributions are obtained. Then, an analysis model for fluid-solid temperature field analysis is established. Taking losses as the distributed heat sources, the 3D thermal field is coupling calculated. The variations of heat transfer coefficient and temperature of fluid in stator grooves along the axial direction, as well as the whole region 3D temperature distribution in HSPMG are obtained. Then, considering the variations of heat sources distributions and heat transfer conditions, 3D temperature fields of HSPMG operating under different speeds are calculated, and the influences of machine operating speed on the HSPMG thermal performance are studied, based on which, the functions of machine temperature with operating speed and stator windings resistance are proposed. The obtained conclusions may provide a useful reference for the design and research of HSPMG.

Analysis of residual gas disturbance on the inner satellite of Inner Formation Flying System

The Inner Formation Flying System （IFFS） consisting of an freely flying in the shield cavity can construct a pure gravity outer satellite and an inner satellite which is a sphere proof mass orbit to precisely detect the earth gravity field. The residual gas in the cavity is a significant disturbance source due to the temperature inhomogeneity and relative motion of the inner satellite. The expressions of the disturbance forces were derived based on the property of rarefied gas, including the radiometer effect and the damping force. According to the current design of IFFS, heat transfer analysis of the cavity and the inner satellite was carried out, and the surface temperature distribution of the cavity and the inner satellite was given. The relative motion of the inner satellite was obtained from the formation control simulation of IFFS. Then the residual gas disturbance was calculated. The disturbance acceleration acting on the inner satellite due to the radiometer effect was on the order of 10^-11 m s^-2 and the damping acceleration was on the order of 10^-15 m s^-2.