一种改进的凝胶分离后蛋白质溶液酶解方法

报道了改进的凝胶电泳分离后蛋白质溶液酶解方法。将凝胶分离后的蛋白转移到PVDF膜上,直接用碳酸氢铵中和从膜上的蛋白洗脱溶液至弱碱性,并在此溶液中直接进行蛋白酶解。方法避免了胶内杂质对质谱鉴定蛋白质的干扰。用标准蛋白进行了验证,并在此基础上鉴定了中国仓鼠卵巢细胞(CHO)细胞系中的16个蛋白点。与已报道的方法比较,本方法蛋白回收率提高到90%左右;与传统的胶内酶解方法比较,本方法具操作简单,实验流程较短;涉及的试剂较胶内酶解少,因此带来的杂质影响小;在蛋白转印以后还可与许多其它实验方法相结合,比如免疫印迹等优点。

理想化法解溶液有关问题

本文对溶液存在状态给出了大胆的理想化假设,即溶液中的一部分液体与另一部分液体之间有明确的分界面,故可以各自分隔开。根据这个设想,可以较简单地解出溶液的倒出、兑入等一系列有关问题。现以教科书上的习题为例,分析解答如下。 例1 一个容器盛满纯药液63升,第一次倒出一部分纯药液后,用水加满,第二次又倒出同样多的药液,再用水加满,这时,容器内剩下的纯药液是28升。问每次倒出液体多少升? 分析 若设每次倒出液体为x升,则可用x的代数式表示第二次倒出x升液体后,剩下纯药液的升数。通常利用浓度公式,可列出第二次倒出的纯药液为x((63-x)/(63))升。

溶剂共沸解聚法制备乙交酯的工艺研究

在邻苯二甲酸丁苄酯存在下,将乙醇酸低聚物加热解聚生成乙交酯和该有机溶剂的共沸物,通过环己烷洗涤后,过滤得到乙交酯粗品。研究结果表明,解聚溶剂与低聚物的质量比为2∶1,助溶剂用量为低聚物质量的25%,解聚温度为250℃,真空压力为3 kPa,催化剂Sb2O3用量为低聚物质量的1%时,条件最优。粗乙交酯的收率可达92.2%,苯酐质量分数低于2%,3次重结晶后乙交酯纯度超过99.5%,并通过核磁共振氢谱、紫外光谱、差示扫描量热仪等对乙交酯进行了表征与纯度分析。

两种用于液质联用分析的蛋白质酶解处理效果比较

【目的】分析和评估两种蛋白质溶液酶解方法,为蛋白质组学研究中的大规模质谱鉴定分析建立一种稳定的样品制备技术。【方法】分别使用TEAB法(实验组A)和TFE法(实验组B)对牛血清白蛋白(BSA)进行还原、烷基化和溶液酶解,再用LTQ-Orbitrap高分辨率质谱仪采集BSA酶切肽段信息,比较两种方法得到的数据信息,分析肽段数目、可变修饰位点和蛋白质覆盖率。【结果】实验组A(TEAB法)获得36个肽段、39个修饰位点,蛋白质平均覆盖率为59.31%;实验组B(TFE法)获得27个肽段、27个修饰位点,蛋白质平均覆盖率为47.83%,实验组A的数据指标与实验组B差异显著。【结论】采用TEAB法酶切体系能实现蛋白质高效率酶切,达到获得较高肽段覆盖率的目的,可为蛋白质组学后期的质谱分析鉴定奠定实验基础。

溶液特性对 EDS 法制备粉体性能的影响

本文简要叙述了EDS 法制备高纯超细粉体与其它液相法的区别,介绍了EDS 法的工艺过程,重点讨论了溶液特性对所制备粉体性能的影响及改善溶液性能的途径。

Relationship between Al(OH)_3 solubility and particle size in synthetic Bayer liquors

Surface tension of sodium aluminate solution and the contact angle between Al（OH）3 particles and aluminate solution were measured, then the dependence of Al（OH）3 solubility on its particle size was calculated and thus the variation of the critical nucleus sizes was determined based on the Ostwald ripening formula. The results show that the Al（OH）3 solubility in sodium aluminate solution decreases with the increment of particle size, and the critical nucleus sizes increase with the rise of alkali concentration, caustic ratio and precipitation temperature. The results also imply that the presence of small particles in seeded precipitation system is an important factor to limit the depth of precipitation.

FLUORESCENCE SPECTRUM ANALYSIS OF ETHER-WATER SOLUTION BASED ON GAUSSIAN DECOMPOSITION METHOD

The fluorescence spectrum of the ether-water solution excited by the ultraviolet light with the wavelength of 245 nm is experimentally detected. Based on the second derivative analysis, the fluorescence spectrum of the ether-water solution is used as Gaussian decomposition and seven Gaussian spectral lines are obtained. The center wavelength, the peak intensity and the half peak bandwidth of each Gaussian spectral line are measured, and the multi-peak fitting is made by using Gaussian primitive parameters. The highest and the lowest oscillation energy level differences in the ground state of each Gaussian spectrum are calculated. It is found that there are seven types of luminescent association molecules formed by ether and water molecules in different configurations existed in the solution. The location of each optimum absorption wavelength and the half peak bandwidth of the Gaussian spectral line is different. The energy level difference with the central wavelength of 304 nm attains the maximum value The result can contribute to the study of the molecular association in ether-water solution.

Measurements of zinc oxide solubility in sodium hydroxide solution from 25 to 100 °C

The solubility of zinc oxide in sodium hydroxide solution was measured in a closed polytetrafluoroethylene vessel from 25 to 100 ℃. The ZnO solubility was determined by employing the method of isothermal solution saturation. The results show that only ZnO solid exists in the equilibrium state in the low concentration alkali regions, and the solubility of zinc oxide is almost invariable with temperature. With the increase of alkali concentration, equilibrium solid turns from ZnO to NaZn（OH）3 suddenly, this mutation is called invariant point. The alkali concentration of the invariant points increases with increasing temperature, but the solubility of NaZn（OH）3 decreases with increasing alkali concentration at the same temperature. At the same Na2O concentration, the higher the temperature is, the higher the solubility of NaZn（OH）3 is.

Dissolution Improvement of Cisapride by Solid Dispersion with HPMC

To prepare a solid dispersion of cisapride with hydroxypropylmethyl cellulose(HPMC E5 LV) as carrier for the purpose of accelerating the in vitro drug release by means ofimproving the solubility of the model drug. Methods Alcohol and simulated gastric fluid (SGF) wereused to dissolve cisapride and HPMC in order to make the model drug dispersed homogeneously in thecarrier. The HPMC-cisapride solid dispersion was then obtained by conventional solvent evaporationmethod. Powder X-ray diffraction (XRD) was used to measure the diffraction peaks of pure carrier,pure cisapride, physical mixture of HPMC with cisapride (4:1), and HPMC-cisapride solid dispersion(4:1) to confirm the crystal existence. The solubility of pure drug and HPMC-cisapride soliddispersion was measured with water, SGF and simulated intestinal fluid (SIF) . The in vitro drugreleases of the sustained release tablet prepared with pure cisapride or HPMC-cisapride soliddispersion were investigated with water and SGF as media, respectively. Results No diffraction peakswere found by X-ray diffraction in the HPMC-cisapride solid dispersion (4:1), indicating that thedrug existed in an amorphous form at that drug-carrier ratio. Compared with the pure drug, thesolubilities of HPMC-cisapride solid dispersion are increased by 239.4% in SGF, 132.6% in water, and117.9% in SIF. According to the in vitro drug release, the sustained release tablet prepared withHPMC-cisapride solid dispersion had a faster drug release than did that prepared with pure drug. Thein vitro drug release profiles were found to comply with Higuchi's rule. Conclusion The in vitrodrug release of the sustained release tablet made by HPMC-cisapride solid dispersion is improvedowing to the increased drug solubility.

Influence of magnesium and aluminum salts on hydrolysis of titanyl sulfate solution

The influence of magnesium and aluminum salts as impurities on the hydrolysis of titanyl sulfate was investigated.The degree of TiOSO4 conversion to hydrated titanium dioxide（HTD） and the particle size of HTD were measured as functions of the concentrations of MgSO4 and Al2（SO4）3 in the TiOSO4 solution.The Boltzmann growth model,which focuses on two main parameters,namely the concentrations of Mg2＋ and Al3＋（ρ（Mg2＋） and ρ（Al3＋）,respectively）,fits the data from the hydrolysis process well with R20.988.The samples were characterized by ICP,SEM,XRD,and laser particle size analyzer.It is found that the addition of Mg SO4 simultaneously improves the hydrolysis ratio and the hydrolysis rate,especially when F（the mass ratio of H2SO4 to TiO2） is high,hydrolysis ratio increases from 42.8% to 83.0%,whereas the addition of Al2（SO4）3 has negligible effect on the chemical kinetics of HTD precipitation during the hydrolysis process,hydrolysis ratio increases from 42.8% to 51.9%.An investigation on the particle size of HTD reveals that the addition of Mg SO4 and Al2（SO4）3 clearly increases the size of the crystallites and decreases the size of the aggregates.

Dissolution kinetics of low grade complex copper ore in ammonia-ammonium chloride solution

The leaching kinetics of Tang-dan refractory low grade complex copper ore was investigated in ammonia-ammonium chloride solution.The concentration of ammonia and ammonium chloride,the ore particle size,the solid-to-liquid ratio and the temperature were chosen as parameters in the experiments.The results show that temperature,concentration of ammonia and ammonium chloride have favorable influence on the leaching rate of copper oxide ores.But,leaching rate decreases with increasing particle size and solid-to-liquid ratio.The leaching process is controlled by the diffusion of the lixiviant and the activation energy is determined to be 23.279 kJ/mol.An equation was also proposed to describe the leaching kinetics.

Efficacy of mosapride citrate with polyethylene glycol solution for colonoscopy preparation

AIM:To evaluate the efficacy and safety of adjunctive mosapride citrate for bowel preparation before colonoscopy. METHODS:We conducted a randomized,double-blind, placebo-controlled study with mosapride in addition to polyethylene glycol(PEG)-electrolyte solution.Of 250 patients undergoing colonoscopy,124 were randomized to receive 2 L PEG plus 15 mg of mosapride citrate (mosapride group),and 126 received 2 L PEG plus placebo(placebo group).Patients completed a questionnaire reporting the acceptability and tolerability of the bowel preparation process.The efficacy of bowel preparation was assessed by colonoscopists using a 5-point scale based on Aronchick's criteria.The primary end point was optimal bowel preparation rates(scores of excellent/good/fair vs poor/inadequate). RESULTS:A total of 249 patients were included in the analysis.In the mosapride group,optimal bowel preparation rates were significantly higher in the left colon compared with the placebo group(78.2%vs 65.6%,P<0.05),but not in the right colon(76.5%vs 66.4%,P=0.08).After excluding patients with severe constipation,there was a significant difference in bowel preparation in both the left and right colon(82.4%vs 66.7%,80.8%vs 67.5%,P<0.05,P<0.01).The incidence of adverse events was similar in both groups. Among the subgroup who had previous colonoscopy experience,a significantly higher number of patients in the mosapride group felt that the current preparation was easier compared with patients in the placebo group(34/72 patients vs 24/74 patients,P<0.05). CONCLUSION:Mosapride citrate may be an effective and safe adjunct to PEG-electrolyte solution that leads to improved quality of bowel preparation,especially in patients without severe constipation.

3D analytical solution for a rotating transversely isotropic annular plate of functionally graded materials

The analytical solution for an annular plate rotating at a constant angular velocity is derived by means of direct displacement method from the elasticity equations for axisymmetric problems of functionally graded transversely isotropic media. The displacement components are assumed as a linear combination of certain explicit functions of the radial coordinate, with seven undetermined coefficients being functions of the axial coordinate z. Seven equations governing these z-dependent functions are derived and solved by a progressive integrating scheme. The present solution can be degenerated into the solution of a rotating isotropic functionally graded annular plate. The solution also can be degenerated into that for transversely isotropic or isotropic homogeneous materials. Finally, a special case is considered and the effect of the material gradient index on the elastic field is illustrated numerically.

Volumetric and Viscometric Studies of 4-Aminobutyric Acid in Aqueous Solutions of Salbutamol Sulphate at 308.15, 313.15 and 318.15K

Density （ρ） and viscosity （η） measurements were carried out for 4-aminobutyric acid in 0.0041,0.0125 and 0.0207 mol·L-1 aqueous salbutamol sulphate at T=308.15,313.15 and 318.15K.The measured values of density and viscosity were used to estimate some important parameters such as apparent molar volume Vφ,limiting apparent molar volume Vφ0,transfer volume △Vφ0,hydration number Hn,second derivative of infinite dilution of partial molar volume with temperature 2Vφ0/T2,viscosity B-coefficients,variation of B with temperature dB/dT,free energy of activation per mole of solvent △μ10＊ and solute △μ20＊,activation entropy △S20＊ and activation enthalpy △H20＊ of the amino acids.These parameters have been interpreted in terms of solute-solute and solute-solvent interactions and structure making/breaking ability of solutes in the given solution.

Measurement and Correlation of Solubility for Propylene in 2-Butanol+Water Solutions

In order to obtain solubility data of propylene in 2-butanol+water solutions, gas-liquid equilibrium(GLE) experiment was carried out at 303.15--333.15 K, 0.3-1.2 MPa with static equilibrium still. Original mass ratios of 2-butanol to water are 1:0，9:1,8:2 and 7:3, respectively. The equilibrium data are correlated with an empirical correlation. The average relative deviation (ARD) between experimental and calculated values is 2.15%,and the maximum relative deviation (MRD) is less than 5%.

Synthesis of mesoporous cerium-zirconium mixed oxides by hydrothermal templating method

Mesoporous cerium-zirconium mixed oxides were prepared by hydrothermal method using cetyl trimethyl ammonium bromide (CTAB) as template. The effects of amount of template, pH value of solution and hydrothermal temperature on mesostructure of samples were systematically investigated. The final products were characterized by XRD, TEM, FT-IR, and BET. The results indicate that all the cerium-zirconium mixed oxides present a meso-structure. At molar ratio of n(CTAB)/n((Ce)+(Zr))= 0.15, pH value of 9, and hydrothermal temperature of 120 ℃, the samples obtained possess a specific surface area of 207.9 m2/g with pore diameter of 3.70 nm and pore volume of 0.19 cm3/g.

Measurement and Correlation for Solubility of （S）-（＋）-2,2-Dimethylcyclopropane Carbox Amide in Different Solvents

（S）-（＋）-2,2-dimethylcyclopropane carbox amide is a key intermediate of Cilastatin, an inhibitor of dehydropeptidase-I. Its corresponding solid-liquid equilibrium data will provide essential support for industrial design and further theoretical studies. The solubilities of （S）-（＋）-2,2-dimethylcyclopropane carbox amide in toluene, dichloromethane, trichloromethane, ethyl acetate, ethanol and pure water at different temperature were measured using the synthetic method by a laser monitoring observation technique. The solubility data were correlated with the modified Apelblat equation.The calculated values were good in agreement with the experimental values.

Liquid-Liquid Equilibria of the Water-Ethanol-Dimethyl Succinate Ternary System

Liquid-liquid equilibrium (LLE) data for the ternary systemwater-ethanol-dimethyl succinate have been determined experimentallyat temperatures ranging from 298.15 to 318.15 K at 5 K intervals.Complete phase diagrams were obtained by determining solubility andthe tie-line data. Tie-line compositions were correlated byOthmer-Tobias method. The universal quasichemical functional groupactivity coefficient (UNIFAC) and modified UNIFAC methods were usedto predict the phase equilibrium in the system using the interactionparameters deter- Mined from experimental data between groups CH_3,CH_2, OH, CH_3 COO and H_2O.