Ni-CNT (carbon nanotube) composite coatings were processed by electrodeposition and their hardness and corrosion characteristics were investigated with variations of CNT concentration in an electrolyte solution and el...Ni-CNT (carbon nanotube) composite coatings were processed by electrodeposition and their hardness and corrosion characteristics were investigated with variations of CNT concentration in an electrolyte solution and electrodeposition current density. With increasing the CNT concentration in the electrodeposition bath and the current density, more CNTs are incorporated into Ni matrix. Hardness values of the Ni-CNT coatings are irrelevant to the CNT concentration in the solution, the current density, and current mode, implying poor adhesion of CNTs to Ni matrix. With increasing the CNT content in the coating, the corrosion resistance of the Ni-CNT composite coating becomes inferior due to the porous microstructure.展开更多
AZ80 magnesium alloys were deformed at 200,250,300,350 and 400℃ with different deformation degree of 50%,75%, 83%,87%and 90%,respectively.The corrosion properties of different deformed AZ80 samples were studied by ga...AZ80 magnesium alloys were deformed at 200,250,300,350 and 400℃ with different deformation degree of 50%,75%, 83%,87%and 90%,respectively.The corrosion properties of different deformed AZ80 samples were studied by galvanic test in 3.5%NaCl solution.The results show that plastic deformation could improve the corrosion resistance of AZ80 alloy;and the corrosion rate of AZ80 deformed at 250℃ with the deformation degree of 83%was the lowest,which was 33%of the as-cast AZ80 alloy.Further studies of the microstructure show that the refined grain size and continuously distribution ofβphase around the grain boundary did have a positive effect on the improvement of corrosion resistance of AZ80 alloys.For AZ80 alloys,the smaller the grain size is,the more homogeneous the structure is,and the better the corrosion resistance is.展开更多
The stress corrosion crack （SCC） susceptibility of ultra-high strength steel AerMet 100 was investigated by slow strain rate technique （SSRT）, tensile with polarization and surface analysis technique. The curves o...The stress corrosion crack （SCC） susceptibility of ultra-high strength steel AerMet 100 was investigated by slow strain rate technique （SSRT）, tensile with polarization and surface analysis technique. The curves of tf^Cl/tf^W -strain rate are divided into three regions： stress-dominated region, SCC-dominated region, and corrosion-dominated region, so as the curves of εf^Cl/εf^W - strain rate and tm/tf-strain rate. The results of tensile tests with polarization show that the main SCC mechanism of AerMet 100 is anodic dissolution, which controls the corrosion process. The three regions have been discussed according to the relationship between the rate of slip-step formation and the rate of dissolution. Fracture appearances in different environments were analyzed by scanning electron microscopy （SEM）. SCC fracture appears as a mixture of intergranular and dimples, while it is totally dimples in the inert environment. The εf becomes the parameter to predict tf because the relationship between εf^Cl/εf^W and tf^Cl/tf^w is a straight line for AerMet 100.展开更多
The corrosion mechanism of AZ31 magnesium alloy used as automobile components and the influence of the concentration of Cl- ion in simulated acid rain(SAR)were studied by electrochemical tests and SEM.The results show...The corrosion mechanism of AZ31 magnesium alloy used as automobile components and the influence of the concentration of Cl- ion in simulated acid rain(SAR)were studied by electrochemical tests and SEM.The results show that pitting corrosion happens around the AlMn phases locating at the grain boundary.The corrosion of AZ31 magnesium alloy in SAR is controlled by the rate of anodic dissolution and hydrogen evolution,and the corrosion rate of AZ31 increases with increasing concentration of Cl- ion.However,the Cl- ion in SAR is not the main influencing factor inducing the pitting corrosion.展开更多
In order to simulate and study the erosion effect process such as the changes of corrosive depth and unconfined compression strength of cemented soil sample in earlier period from 0 day to 60 days, a series of tests i...In order to simulate and study the erosion effect process such as the changes of corrosive depth and unconfined compression strength of cemented soil sample in earlier period from 0 day to 60 days, a series of tests including unconfined compressive tests, measuring the blocks＇ sizes, and taking photos, are conducted on the cemented soil blocks which were cured in different concentrations of H2SO4 solutions. The results of tests show that the corrosive depth is increasing and the unconfined compression strength is decreasing with the increase of H2SO4 solution concentration at the same erosion time, and the corrosive degree is increasing with the corrosive time. In the earlier state, the corrosive effect is serious, but the effect becomes slow in the later state in the same concentrated H2SO4 solution. After take statistics the date, a coefficient a is put forward to predict the reduction of the compressive strength of cemented soil in various concentration of H2SO4 solution, which could be used in practical design.展开更多
基金supported by the Center for Electronic Packaging Materials of Korea Science Engineering Foundation
文摘Ni-CNT (carbon nanotube) composite coatings were processed by electrodeposition and their hardness and corrosion characteristics were investigated with variations of CNT concentration in an electrolyte solution and electrodeposition current density. With increasing the CNT concentration in the electrodeposition bath and the current density, more CNTs are incorporated into Ni matrix. Hardness values of the Ni-CNT coatings are irrelevant to the CNT concentration in the solution, the current density, and current mode, implying poor adhesion of CNTs to Ni matrix. With increasing the CNT content in the coating, the corrosion resistance of the Ni-CNT composite coating becomes inferior due to the porous microstructure.
基金Projects(50605059,50735005)supported by the National Natural Science Foundation of ChinaProject(2008062)supported by Shanxi Province Foundation for Returness
文摘AZ80 magnesium alloys were deformed at 200,250,300,350 and 400℃ with different deformation degree of 50%,75%, 83%,87%and 90%,respectively.The corrosion properties of different deformed AZ80 samples were studied by galvanic test in 3.5%NaCl solution.The results show that plastic deformation could improve the corrosion resistance of AZ80 alloy;and the corrosion rate of AZ80 deformed at 250℃ with the deformation degree of 83%was the lowest,which was 33%of the as-cast AZ80 alloy.Further studies of the microstructure show that the refined grain size and continuously distribution ofβphase around the grain boundary did have a positive effect on the improvement of corrosion resistance of AZ80 alloys.For AZ80 alloys,the smaller the grain size is,the more homogeneous the structure is,and the better the corrosion resistance is.
基金Project(51171011) supported by the National Natural Science Foundation of China
文摘The stress corrosion crack （SCC） susceptibility of ultra-high strength steel AerMet 100 was investigated by slow strain rate technique （SSRT）, tensile with polarization and surface analysis technique. The curves of tf^Cl/tf^W -strain rate are divided into three regions： stress-dominated region, SCC-dominated region, and corrosion-dominated region, so as the curves of εf^Cl/εf^W - strain rate and tm/tf-strain rate. The results of tensile tests with polarization show that the main SCC mechanism of AerMet 100 is anodic dissolution, which controls the corrosion process. The three regions have been discussed according to the relationship between the rate of slip-step formation and the rate of dissolution. Fracture appearances in different environments were analyzed by scanning electron microscopy （SEM）. SCC fracture appears as a mixture of intergranular and dimples, while it is totally dimples in the inert environment. The εf becomes the parameter to predict tf because the relationship between εf^Cl/εf^W and tf^Cl/tf^w is a straight line for AerMet 100.
基金Project(50901082)supported by the National Natural Science Foundation of ChinaProject(2007CB613705)supported by the National Basic Research Program of China
文摘The corrosion mechanism of AZ31 magnesium alloy used as automobile components and the influence of the concentration of Cl- ion in simulated acid rain(SAR)were studied by electrochemical tests and SEM.The results show that pitting corrosion happens around the AlMn phases locating at the grain boundary.The corrosion of AZ31 magnesium alloy in SAR is controlled by the rate of anodic dissolution and hydrogen evolution,and the corrosion rate of AZ31 increases with increasing concentration of Cl- ion.However,the Cl- ion in SAR is not the main influencing factor inducing the pitting corrosion.
文摘In order to simulate and study the erosion effect process such as the changes of corrosive depth and unconfined compression strength of cemented soil sample in earlier period from 0 day to 60 days, a series of tests including unconfined compressive tests, measuring the blocks＇ sizes, and taking photos, are conducted on the cemented soil blocks which were cured in different concentrations of H2SO4 solutions. The results of tests show that the corrosive depth is increasing and the unconfined compression strength is decreasing with the increase of H2SO4 solution concentration at the same erosion time, and the corrosive degree is increasing with the corrosive time. In the earlier state, the corrosive effect is serious, but the effect becomes slow in the later state in the same concentrated H2SO4 solution. After take statistics the date, a coefficient a is put forward to predict the reduction of the compressive strength of cemented soil in various concentration of H2SO4 solution, which could be used in practical design.
