哈氏B-3合金大型压力容器的研制

在简要介绍哈氏合金的发展、分类与使用的基础上,重点介绍了哈氏B-3合金的发展、性能与各项合格指标。并结合世界首台哈氏B-3合金大型压力容器制造的实例,详细介绍了该类材料在焊接制造大型压力容器时在施工环境、冷热加工、耐蚀试验与质量控制等方面的具体要求。

Microstructure and fracture toughness of a TiAl-Nb composite consolidated by spark plasma sintering

A TiAl-Nb composite was prepared by spark plasma sintering （SPS） at 1250 °C and 50 MPa for 5 min from prealloyed TiAl powder and elemental Nb powder in a molar ratio of 9：1 for improving the fracture toughness of TiAl alloy at room temperature. The microstructure, phase constitute, fracture surface and fracture toughness were determined by X-ray diffractometry, electron probe micro-analysis, scanning and transmission electron microscopy and mechanical testing. The results show that the sintered samples mainly consist of γ phase, O phase, niobium solid solution （Nbss） phase and B2 phase. The fracture toughness is as high as 28.7 MPa？m1/2 at room temperature. The ductile Nbss phase plays an important role in absorbing the fracture energy in front of the cracks. Moreover, B2 phase can branch the propagation of the cracks. The microhardness of each phase of the composite was also tested.

Ductility improvement methods for commercial AZ31B magnesium alloy in cold forging

In order to realize cold forging of magnesium alloys in practical application,some methods for ductility improvement of a commercial wrought AZ31B magnesium alloy(Mg-3%Al-1%Zn,mass fraction) at room temperature were suggested.The effects of heat treatment before forging and hydrostatic pressure during forging on the ductility were investigated in cold upsetting and cup forging.High-temperature annealing was effective to reduce the degree of the texture anisotropy of the specimen,and it was found that the forging limit of the annealed specimen was improved in cold forging.On the other hand,cold cup forging of the annealed specimen was carried out with applying counter pressure.By applying counter pressures of 100-200 MPa during forging,the critical punch stroke for forging limit of the specimen without crack was improved by 25%in punch stroke.

Analysis on structure of igneous formation with fractal dimension of logs

Reflecting the structure of igneous formation by calculating fractal dimension of logs,the fractal dimension of pyroclastic is larger than lava.Structure of pyroclastic is more complicated than that of lava,so reflecting the structure of igneous formation's complexity with fractal dimension is feasible.It is feasible to reflect the structure of igneous formation's complexity with fractal dimension.

Structure and properties of AZ31B magnesium alloy sheets processed by repeatedly unidirectional bending at different temperatures

Repeatedly unidirectional bending(RUB) was applied to the magnesium alloy sheet to improve the basal texture.The effect of RUB temperature on resulting structure and room temperature properties was investigated.The texture components of the sheet undergoing RUB at recovery temperature were similar to those of the sheet undergoing RUB at room temperature(RT).As the RUB temperature increased to above recrystallization temperature,the texture components became more disperse and the pyramidal components increased.With the increase of RUB temperature,the grain size near the surface of the sheets undergoing RUB tended to grow up.When the sheets were processed by RUB at medium-high temperature followed by annealing at 533 K,the yield strength and fracture elongation were lower than those of the cold rolled sheet;however,the Erichsen value was slightly higher than that of the cold rolled sheet.The sheet undergoing RUB at RT followed by annealing at 533 K represented the best mechanical properties.

The Characteristics of Seismic Activity Before the Devastating Earthquake with M_W9.0 Off the West Coast of Northern Sumatra

The characteristics of seismic activity in different time-spatial domain before the M_W9.0 earthquake were studied. The results are as follows:The activity of the deep earthquakes in the north boundary zone of the Australian plate had been evidently strengthened since 1994, showing an increased frequency, magnitude and depth, especially in regards to the heterogeneous distribution of the earthquake depth (namely between 500km and 689km). Meanwhile the shallow earthquakes of M≥7.0 in the Sumatra island and its vicinity had been obviously strengthened too, and formed a strengthening area with a length of about 1000 km and width 300 km. ②The time distribution of global strong earthquakes with M≥7.0 shows that the character of anomalous seismic quiescence-activity one year before the M_W9.0 earthquake and during its active period, the strong earthquakes formed a seismic belt striking in NWW direction. At the same time, there is a seismic gap formed by earthquakes of M≥5.0 in the epicenter and its neighboring region. ③Two deep earthquakes of M≥7.0 occurred in the west and in the east of the north boundary zone of the Australian plate half year ago. It is notable that one of them occurred in the Sumatra island where no deep earthquake with M≥6.0 has occurred in the past thirty years. ④The space distribution of moderate shocks occurring three days ago exhibited a NWW-strike seismic belt along the north boundary zone of the Australian plate. ⑤The activity of volcanoes distributed in the north boundary zone of the Australian plate had been strengthened in the past 4 years, especially several months before the occurrence of the M_W9.0 earthquake.

Effect of processing parameters on the electromagnetic radiation emission during plastic deformation and crack propagation in copper-zinc alloys

This paper presents some investigations on the effect of processing parameters on the emission of electromagnetic radiation （EMR） during plastic deformation and crack propagation in copper-zinc alloys. Timing of the EMR emissions, maximum stress during crack instability, stress-intensity factor, elastic strain energy release rate, maximum EMR amplitude, RMS value of EMR amplitude, EMR frequency and electromagnetic energy release rate were analysed for the effect of rolling directions at different percentage of zinc content in Cu-Zn alloy specimens. The same parameters were also analysed for 68-32 Cu-Zn alloy specimens at different annealing temperatures and at different angles 0, to the rolling direction. EMR emissions are observed to be highly anisotropic in nature. At θ=45° to 60°, marked changes in mechanical and electromagnetic parameters were observed. Specimens annealed at 500℃, just above the recrystallization temperature, and at 700℃, when grain-size growth is rapid, EMR responses have been found to have well-defined patterns.

Reservoir characteristics and hydrocarbon accumulation of Carboniferous volcanic weathered crust of Zhongguai high area in the western Junggar Basin, China

Based on the drilling,cores,logs,seismic,laboratory analysis and so on,reservoir characteristics and hydrocarbon accumulation of Carboniferous volcanic weathered crust in Zhongguai high area are studied.Volcanic rocks were formed in an island arc environment.The lithology is mainly andesite and tuff;Reservoir spaces are mainly secondary pore,fracture and their combination forms,fractures have a better effect on reservoir seepage;There are four layer structures of volcanic weathered crust,weathered clay layer,strongly weathered zone,weakly weathered zone and unweathered zone and strongly weathered zone is the best,which is the main reservoir development zone;The development of reservoir is mainly affected by weathering-leaching,lithology and lithofacies,and fault(fracture);Effective reservoirs could reach to 480 m thickness(high quality reservoirs are within 240 m).Carboniferous volcanic reservoirs are distributed along three zones,which are near the fault zone,high structural part,favorable lithofacies development zone,and one plane,which is near the unconformity.

Improvement of hydrogen embrittlement and stress corrosion cracking by annealing for Al-4.4Mg-0.6Mn alloy

With no annealing treatment, cathodic polarization trends in 5083F A1 alloy revealed concentration polarization and activation polarization. However, the annealed specimens have lower current densities at corrosion protection potential compared to the non-annealed specimen. The results of SSRTs conducted in seawater at the applied potential range of-l.8 V to -0.5 V indicated that the maximum tensile strength, elongation, and time-to-fracture had high values at applied potentials of -0.7 to -1.4 V. The maximum tensile strength, elongation, and time-to-f？acture decreased when the potential values were beyond this range in either anodic or cathodic direction. In general, the increased shear lip caused by annealing treatment indicates elongation. Time-to-fracture would likely increase with elongation. Potentials between -0.5 V to -0.6 V were found to be in the region of stress corrosion cracking. The corrosion protection zone was determined to be -0.7 V to -J,4 V because these potential ranges produced good mechanical properties. Potential less than -1.4 V produced a fractured surface with a mixture of dimples （ductile fractures） and a quasi-cleavage pattern resulting from the effects of hydrogen gas.

Effect of concentration of ATH on mechanical properties of polypropylene/aluminium trihydrate(PP/ATH) composite

Aluminium trihydrate(ATH) is being extensively added to polypropylene(PP) to make a fire retardant composite. Blends of PP/ATH composite are more fire resistant as compared to pure PP. Percentage proportion of both the constituents in the final composite depends upon the application. Improvement in the fire retardant properties of such composites have been studied and published in literature but effects on mechanical strength have not been addressed. The effect of concentration of ATH on the strength of PP/ATH composite was presented. The tensile, flexural and fracture properties were studied and discussed. Experimental tests, ASTM analytical formulae and finite element approach were used. It has been found that increase in ATH has an inverse effect on the mechanical strength.

Post-fire Behavior of Ordinary Concrete Reinforced with Short Steel Fibers

Concrete is a widely used material in civil construction and may be submitted to high working temperatures under various circumstances. Many factors influence the behavior of this material at high temperatures, which usually leads to the evaporation of the hydrated cement. The dehydrated cement undergoes a contraction, simultaneously with the thermal expansion of the inert fraction of the material. As a consequence of these conflicting expansions and contractions, the material cracks and its strength and modulus of elasticity decrease significantly. On the other hand, the addition of short metallic fibers to the material increases its toughness, probably due to its action on the cracking behavior of the composite. It is thus expected that a concrete containing metallic fibers should maintain its original properties even after exposure to elevated temperatures. This paper presents an evaluation of the influence of steel fibers on the microstructure and toughness of concretes submitted to high tenaperatures. The bending behavior, under strain rate control, of concretes with a strength of 30 MPa and containing short steel fibers, submitted to a previous treatment at 500 ℃, was analyzed. It was observed that, after both heat treatments, the addition of metallic fibers to concrete was able to maintain the pseudo-ductility and load-carrying capacity of this composite material.

Study on Technology for Quenching Catalytic Pyrolysis Gas

This article describes the application of technology for quenching catalytic pyrolysis gas at the Daqing commercial CPP test unit and the Shenyang commercial CPP production unit.On the basis of results for application of the Shenyang CPP unit this paper puts forward an improved process flow scheme for quenching the pyrolysis gas and made calculations using the process flowsheet software.Case Ⅰ of the process flow scheme,which is designed for full circulation of slurry,intends to use the pyrolysis light oil and fresh feed oil as the quenching media with the product slurry oil and fresh feedstock being discharged from the quench cooler bottom and routed directly to the reactor so that the fresh feed oil can be preheated prior to pyrolysis.Case Ⅱ of the process flow scheme intends to adopt recycle oil as the quenching medium with the product slurry and recycle oil being discharged from the quench cooler bottom to the fractionator,which then delivers the slurry from the bottom.These two cases for improving the process flow diagram can all effectively control the density and viscosity of the quenching medium to secure the smooth operation of quench cooler.

Regional metallogenic structure based on aeromagnetic data in northern Chile

Chile is a very important country that forms part of the Andean metallogenic belts. The Atacama and Domeyko fault systems in northern Chile control the tectonic- magmatic activities that migrate eastward and the types of mineral resources. In this paper, we processed and interpreted aeromagnetic data from northern Chile using reduction to pole, upward field continuation, the second derivative calculation in the vertical direction, inclination angle calculation, and analytical signal amplitude analysis. We revealed the locations and planar distribution characteristics of the regional deep faults along the NNE and NS directions. Furthermore, we observed that the major reasons for the formation of the tectonic-magmatic rocks belts were the nearly parallel deep faults distributed from west to east and multiple magmatic activities along these faults. We ascertained the locations of volcanic mechanisms and the relationships between them using these regional deep faults. We deduced the spatial distributions of the basic-intermediate, basic, and acidic igneous rocks, intrusive rocks, and sedimentary sequences. We showed the linear positive magnetic anomalies and magnetic anomaly gradient zones by slowly varying the background, negative magnetic anomaly field, which indicated the presence of strong magmatic activities in these regional deep faults; it also revealed the favorable areas of copper and polymetallic mineralization. This study provides some basic information for further research on the geology, structural characteristics, and mineral resource prospecting in northern Chile.

S-wave Q structure of the crust and upper mantle beneath Yunnan from surface waves

A phase-matched filtering technique is applied to extract fundamental mode signals from Rayleigh waves recorded at 62 digital seismic stations in the Yunnan and Sichuan regions.We use the fundamental mode of vibrations at two stations that are located on the same great circle as the focus to calculate an inter-station attenuation coefficient of the Rayleigh wave with periods between 0.40 and 80.64 s,and invert for the inter-station S-wave Q-factor (Qβ) at depths of 0-200 km.The results indicate that Qβ in Yunnan is 20-140,presenting a low Qβ background with apparent lateral variation.Taking the Honghe Fault as the boundary,Qβ of the crust is only 20 on the west side,extending to a depth of 120 km.The distribution of Qβ is consistent with large-scale Cenozoic volcanic and intrusive rocks in western Yunnan,implying that the crust and mantle are in the thermally active state.In the eastern Yunnan Block,east of the Xiaojiang Fault,Qβ in the upper 120 km is 140 in the south but only 20 in the north.Additionally,around the Dukou-Chuxiong in the mid-Yunnan Block,Qβ in the lithosphere is relatively high at 60-100,corresponding to a stiff crust.This is because the suture between the Indian and Eurasian plates reversed the tension in the rifting stage into the compression of orogenesis,leading to the closure of a gap in the crust.After some time,interstitial fluids gradually disappeared,resulting in a high velocity layer in the crust and low heat flow on the surface.The Yunnan region consists of an obvious block of elevated Qβ,distributed within the low background,consistent with the distribution of heat-flow values on the surface.The Honghe and Xiaojiang faults are tectonic boundaries in addition to being boundaries between regions of high and low crustal Qβ.The low Qβ is probably the result of crustal rupture and disturbance caused by strong earthquakes and the upwelling of hot substances along the deep fault zones.