Contrast tests were carried out to study the fatigue performance of the butt joints treated by ultrasonic peening, aiming at the improvement of ultrasonic peening treatment(UPT) on welded joints of a new material. The...Contrast tests were carried out to study the fatigue performance of the butt joints treated by ultrasonic peening, aiming at the improvement of ultrasonic peening treatment(UPT) on welded joints of a new material. The material is a new generation of fine grain and high purity SS400 steel that has the same ingredients as the traditional low carbon steel. The specimens are in two different states:welded and ultrasonic peening conditions. The corresponding fatigue testing data were analyzed according to the regulation of the statistical method for fatigue life of the welded joints established by International Institute of Welding(IIW). Welding residual stress was considered in two different ways: the constant stress ratio R=0.5 and the Ohta method. The nominal stress-number (σ-N)curves were corrected because of the different plate thickness compared to the standard and because there was no mismatch or angular deformation. The results indicated that: 1) Compared with the welded specimens, when the stress range was 200 MPa, the fatigue life of the SS400 steel specimens treated by ultrasonic peening is prolonged by over 58 times, and the fatigue strength FAT corresponding to 106 cycles is increased by about 66%; 2) As for the SS400 butt joint (single side welding double sides molding), after being treated by UPT, the nominal S-N curve (m=10) of FAT 100 MPa(R=0.5) should be used for fatigue design. The standard S-N curves of FAT 100 MPa(R=0.5, m=10) could be used for fatigue design of the SS400 steel butt joints treated by ultrasonic peening.展开更多
We study s-wave pion-pion scattering length in lattice QCD for pion masses ranging from 330 MeV to 466 MeV. In the ＂Asqtad＂ improved staggered fermion formulation, we measure full ππ four-point correlators for iso...We study s-wave pion-pion scattering length in lattice QCD for pion masses ranging from 330 MeV to 466 MeV. In the ＂Asqtad＂ improved staggered fermion formulation, we measure full ππ four-point correlators for isospin I = 0 and 2 channels, and use chiral perturbation theory at next-to-leading order to extrapolate our simulation results. Extrapolating to the physical pion mass yields scattering lengths as mna01=2 = -0.041 6（2） and mna01= 0.186（2） for isospin I = 2 and 0 channels, respectively. Our lattice simulation for ππ scattering length in I = 0 channel is an exploratory study, where we include the disconnected contribution, and our preliminary result is near to its experimental value. These simulations are carried out with MILC 2 ＋ 1 flavor gauge configurations at lattice spacing a ≈0.15 fm.展开更多
文摘Contrast tests were carried out to study the fatigue performance of the butt joints treated by ultrasonic peening, aiming at the improvement of ultrasonic peening treatment(UPT) on welded joints of a new material. The material is a new generation of fine grain and high purity SS400 steel that has the same ingredients as the traditional low carbon steel. The specimens are in two different states:welded and ultrasonic peening conditions. The corresponding fatigue testing data were analyzed according to the regulation of the statistical method for fatigue life of the welded joints established by International Institute of Welding(IIW). Welding residual stress was considered in two different ways: the constant stress ratio R=0.5 and the Ohta method. The nominal stress-number (σ-N)curves were corrected because of the different plate thickness compared to the standard and because there was no mismatch or angular deformation. The results indicated that: 1) Compared with the welded specimens, when the stress range was 200 MPa, the fatigue life of the SS400 steel specimens treated by ultrasonic peening is prolonged by over 58 times, and the fatigue strength FAT corresponding to 106 cycles is increased by about 66%; 2) As for the SS400 butt joint (single side welding double sides molding), after being treated by UPT, the nominal S-N curve (m=10) of FAT 100 MPa(R=0.5) should be used for fatigue design. The standard S-N curves of FAT 100 MPa(R=0.5, m=10) could be used for fatigue design of the SS400 steel butt joints treated by ultrasonic peening.
基金Supported by Fundamental Research Funds for the Central Universities under Grant No. 2010SCU23002the Startup Grant fromthe Institute of Nuclear Science and Technology of Sichuan University
文摘We study s-wave pion-pion scattering length in lattice QCD for pion masses ranging from 330 MeV to 466 MeV. In the ＂Asqtad＂ improved staggered fermion formulation, we measure full ππ four-point correlators for isospin I = 0 and 2 channels, and use chiral perturbation theory at next-to-leading order to extrapolate our simulation results. Extrapolating to the physical pion mass yields scattering lengths as mna01=2 = -0.041 6（2） and mna01= 0.186（2） for isospin I = 2 and 0 channels, respectively. Our lattice simulation for ππ scattering length in I = 0 channel is an exploratory study, where we include the disconnected contribution, and our preliminary result is near to its experimental value. These simulations are carried out with MILC 2 ＋ 1 flavor gauge configurations at lattice spacing a ≈0.15 fm.
