Study on Curing Effect and the Waste Heat Recovering Equipment Design of Flue Gas of Bulk Curing Barn

In order to realize tobacco curing with energy saving and emission reduc- ing and lower cost, the waste heat recovering equipment was designed and built on blowing-upward type bulk curing barn. The comparative experiment of tobacco leaf curing was conducted between a bulk curing barn with waste heat of flue gas and conventional bulk curing barn. The results showed that the effect of saving coal in bulk curing barn with waste heat of flue gas was obvious than the contrast. The coal consumption quantity was 1.531 kg per kg of dry tobacco leaf. The saving coal in bulk curing barn with use waste heat of flue gas was 0.181 kg per kg of dry tobacco leaf than the contrast and saving coal rate was 10.57%. The electricity consumption quantity was 0.593 kWh per kg of dry tobacco leaf. The saving elec- tricity quantity in bulk curing barn with use waste heat of flue gas was 0.022 kWh/kg and the saving electricity rate was 3.58% than the contrast. The saving curing cost was 0.158 yuan per kg of dry tobacco leaf and saving cost rate 9.09% in bulk cur- ing barn with use waste heat of flue gas than the contrast. The appearance quality, grade structure and primary chemical composition had no significant difference be- tween bulk curing barn with use waste heat of flue gas and the contrast.

Optimal Analysis of Pure Low-Temperature Waste Heat Recovery Generation System

In this paper, a detailed thermodynamic analysis of the pure low-temperature waste heat recovery generation system is presented. The parameters affecting the system performance are compared to obtain the most significant ones; furthermore, parameter values are optimized for the largest power generating capability of the system. It is found that the most important parameters are inlet flue gas temperature, steam pressure and the pinch point temperature difference. There is an optimal superheated steam pressure value for giving the maximum generation power per unit flue gas. With the increase of inlet flue gas temperature, the generating power increases and the optimized steam pressure rises as well. However, with increase in pinch point temperature difference, the generating power decreases and the optimized steam pressure decreases as well. The theoretical calculation provides a theoretical basis for the parameters optimization in the design of the pure low-temperature waste heat recovery eeneration swtem

纯低温余热发电在玻璃行业应用前景可期

玻璃工业是能源消耗大户。目前,国内的平板玻璃行业大多采用浮法玻璃生产技术,大约有160余条浮法玻璃熔炉,工艺水平已经与国际水平不相上下,但在能耗方面与国际先进水平相比仍然存在着较大差距。

Mathematical Simulation of Lithium Bromide Solution Laminar Falling Film Evaporation in Vertical Tube

For utilization of the residual heat of flue gas to drive the absorption chillers,a lithium-bromide falling film in vertical tube type generator is presented.A mathematical model was developed to simulate the heat and mass coupled problem of laminar falling film evaporation in vertical tube.In the model,the factor of mass transfer was taken into account in heat transfer performance calculation.The temperature and concentration fields were calculated.Some tests were conducted for the factors such as Re number,heating flux,the inlet concentration and operating pressure which can affect the heat and mass transfer performance in laminar falling film evaporation.The heat transfer performance is enhanced with the increasing of heat flux.An increasing inlet concentration can weaken the heat transfer performance.The operating pressure hardly affects on heat and mass transfer.The bigger inlet Re number means weaker heat transfer effects and stronger mass transfer.The mass transfer obviously restrains the heat transfer in the falling film solution.The relation between dimensionless heat transfer coefficient and the inlet Re number is obtained.

Experimental study of the flow and heat transfer of a gas–water mixture through a packed channel

Waste heat recovery from the flue gas of gasfired boilers was studied experimentally by measuring the flow and heat transfer of air and water through six kinds of packing with saturated humid air as the simulated flue gas.The experiments measured the effects of inlet air temperature, inlet air velocity and circulating water flow rate on the flow and heat transfer. The results show that higher inlet air temperatures and lower inlet air velocities lower the flow resistance and increase the heat transfer coefficient. The stainless steel packing had better surface wettability and larger thermal conductivity than the plastic packing, which enhanced the heat transfer between the water and the saturated moist air. When both the flow resistance reduction and the heat transfer enhancement were considered, the experimental results gave an optimal packing-specific surface area. A packed heat exchanger tower was designed for waste heat recovery from the flue gas of gas-fired boilers based on the experimental results which had better flow and heat transfer characteristics with lower pump and fan power consumption, more stable system operation and less thermal fluctuations compared with a non-packed heat transfer system with atomized water.

Waste heat recovery and denitrification of flue gases from gas-fired boilers

A waste heat recovery and denitrification system was developed for improving energy conservation and emissions control especially for control of PM2.5 particles and haze. The system uses enhanced heat and mass transfer techniques in a packed heat exchange tower with self-rotation and zero-pressure spraying, low temperature NO oxidation by ozone, and neutralization with an alkali solution. Operating data in a test project gave NOx in the exhaust flue gas of less than 30 mg/Nm3 with an ozone addition rate of 8 kg/h and spray water p H of 7.5–8, an average heat recovery of 3 MW, and an average heat supply of 7.2 MW.