关于在部分林场改变烧材结构的探讨

本文通过对以煤代木取暖、附助以煤气做饭的燃料结构及对丢弃的细小枝丫为烧材的可行性研究后 ,确认烧小枝丫方案可行 。

Experimental investigation of performance properties and agglomeration behavior of fly ash from gasification of corncobs

The gasification industries make use of biomass residue as feedstock to produce synthesis gas,but the gasification of this waste biomass generates tons of ash everyday.Performance properties and agglomeration behavior of corncob ash(CCA) collected from the gasification of corncobs in a pilot-scale gasification station were investigated by using some experimental methods.Based on the chemical composition results,the agglomeration tendency of CCA from combustion and gasification process was also analyzed.Chemical analysis shows that the fly ash is mainly composed of inorganic matters formed by K,Mg,Ca,Na,Fe,Al,S,etc.The agglomeration characteristics indicate that the slagging degree increases with the increase of ashing temperature,and the slagging tendency of these CCA samples from gasification or combustion is different with various slagging indices.All CCA samples from combustion or gasification can cause slagging/fouling problems in thermal conversion systems.The applications of CCA are closely related to its performances,and CCA has the potential to be used in various fields,for example,as a material for ceramic products and activated carbon,as an adsorbent,as a crude fertilizer,and as a structural material.

Microstructure and properties of alumina-silicon carbide nanocomposites fabricated by pressureless sintering and post hot-isostatic pressing

A1203/5%SIC nanocomposites were fabricated by pressureless sintering using MgO as a sintering aid and then post hot-isostatic pressed （HIP）, which can subsequently break through the disadvantage of hot-pressing process. The MgO additive was able to promote the densification of the composites, but could not induce the grain growth of A1203 matrix due to the grain growth inhibition by nano-sized SiC particles. After HIP treatment, A12OJSiC nanocomposites achieved full densification and homogeneous distribution of nano-sized SiC particles. Moreover, the fracture morphology of HIP treated specimens was identical with that of the hot-pressed A1203/SiC nanocomposites showing complete transgranular fracture. Consequently, high fracture strength of 1 GPa was achieved for the A1203/5%SIC nanocomposites by pressureless sintering and post HIP process.

Phase composition, transition and structure stability of functionally graded cemented carbide with dual phase structure

The phase composition, phase transition and phase structure transformation of the wire-cut section of functionally graded WC-Co cemented carbide with dual phase structure were investigated by XRD phase analysis. It is shown that the composition of η phase in the core zone is Co_3W_3C (M_6 C type). The structure of cobalt based solid solution binder phase is fcc type. At the cooling stage of the sintering process, the phase transition of η phase, i.e. M_6C→M_12C and the martensitic phase transition of the cobalt based solid solution binder phase, i.e. fcc→hcp are suppressed, which facilitates the strengthening of the alloy. Because the instantaneous temperature of the discharge channel is as high as 10 000 ℃ during the wire cutting process, the processed surface is oxidized. Nevertheless, the oxide layer thickness is in micro grade. In the oxide film, η phase is decomposed into W_2C and CoO, and cobalt based solid solution binder is selectively oxidized, while WC remains stable due to the existence of carbon containing liquid organic cutting medium.

Effects of sintering temperature on microstructure and performance of Ti-based Ti-Mn alloy anodic material

A novel Ti-based Ti-Mn composite anode used for electrolytic manganese dioxide(EMD) fabrication was developed by a two-step heating manganizing technique.The effects of sintering temperature on the manganized microstructure and the performance of the composite anode were studied by scanning electron microscopy(SEM),mechanical properties tests at room temperature and electrochemical methods.The results show that the thickness of the diffusion layer increases with the increase of sintering temperature up to 1 100 °C;whereas,the surface Mn content increases and reaches the maximum at 1 000 °C and then decreases thereafter.Lower surface Mn content is beneficial for the enhanced corrosion resistance and lowered open cell voltage in electrolytic process.The new anode prepared under the optimized conditions has been applied in industry and exhibits superior economic benefits to conventional Ti anodic materials.