A procedure of low temperature solid-phase sintering（LTSS） was carried out to fabricate sintered metal fibrous media（SMFM） with high specific surface area.Stainless steel fibers which were produced by cutting proc...A procedure of low temperature solid-phase sintering（LTSS） was carried out to fabricate sintered metal fibrous media（SMFM） with high specific surface area.Stainless steel fibers which were produced by cutting process were first plated with a coarse copper coating layer by electroless plating process.A low-temperature sintering process was then completed at about 800 °C for 1 h under the protection of hydrogen atmosphere.The results show that a novel SMFM with complex surface morphology and high specific surface area（0.2 m2/g） can be obtained in this way.The effect of sintering temperature on the surface morphology and specific surface area of SMFM was studied by means of scanning electron microscopy and Brunauer-Emmett-Teller.The damage of micro-structure during the sintering process mainly contributed to the loss of specific surface area of SMFM and the optimal sintering temperature was 800 °C.展开更多
In order to examine the leaching rate of potassium chloride from the sintering dust by water,surface morphology and inner structure of the dust,especially the existing state of potassium chloride,were observed by scan...In order to examine the leaching rate of potassium chloride from the sintering dust by water,surface morphology and inner structure of the dust,especially the existing state of potassium chloride,were observed by scanning electron microscopy（SEM） and linear scanning technique via energy dispersive spectroscopy（EDS）.The characterization shows that the sintering dusts are mostly porous composites or agglomerates of the fine dust particles with size less than 10 μm,and the potassium chloride and sodium chloride particles are partly covered by other water insoluble matters in the dust which consist of elements iron,calcium and etc.Exposure of potassium chloride in the agglomerated dust matrix of this kind suggests that the leaching can be simply perceived as the dissolution of water soluble matters in the dust.On-line monitor of specific electrical conductivity of the leaching system verifies the prediction that leaching kinetics of potassium chloride from the sintering dust fits dissolution model well.Leaching equilibrium can be reached within 5 min with potassium leaching ratio more than 95%.展开更多
The effects of sintering atmosphere on the properties of symmetric TiO2 membranes are studied with regard to sintering behavior, porosity, mean pore size, surface comPosition. and surface charge properties. The exerim...The effects of sintering atmosphere on the properties of symmetric TiO2 membranes are studied with regard to sintering behavior, porosity, mean pore size, surface comPosition. and surface charge properties. The exerimental results show that the symmetric TiO2 membranes display better sintering activity in the air than in argon, and the mean pore diameters and porosities of the membrane sintered in argon are higher than those of the membrane sintered in the air at the same temperature. The surface compositions of the symmetric TiO2 membrane sintered in the air and in argon at different temperatures, as studied by X-ray photoelectron spectroscopy, are discussed in terms of their chemical composition, with particular emphasis on the valence state of the titanium ions. The correlation between the valence state of the titanium ions at the surface and the surface charge properties is examined.It is found that the presence of Ti^3＋, introduced at the surface of the symmetric TiO2 membranes by sintering in a lower partial pressure of oxygen, is related to a significant decrease in the isoelectric point. TiO2 with Ti^4＋ at the interface has an isoelectric point of 5.1, but the non-stoichiometric TiO2-x with Ti^3＋ at the interface has a lower isoelectric point of 3.6.展开更多
Superhydrophilic surfaces were fabricated on copper substrates by an electrochemical deposition and sintering process. Superhydrophobic surfaces were prepared by constructing micro/nano-structure on copper substrates ...Superhydrophilic surfaces were fabricated on copper substrates by an electrochemical deposition and sintering process. Superhydrophobic surfaces were prepared by constructing micro/nano-structure on copper substrates through an electrochemical deposition method. Conversion from superhydrophobic to superhydrophilic was obtained via a suitable sintering process. After reduction sintering, the contact angle of the superhydrophilic surfaces changed from 155° to 0°. The scanning electron microscope （SEM） images show that the morphology of superhydrophobic and superhydrophilic surfaces looks like corals and cells respectively. The chemical composition and crystal structure of these surfaces were examined using energy dispersive spectrometry （EDS） and X-ray diffraction （XRD）. The results show that the main components on superhydrophobic surfaces are Cu, Cu2O and CuO, while the superhydrophilic surfaces are composed of Cu merely. The crystal structure is more inerratic and the grain size becomes bigger after the sintering. The interracial strength of the superhydrophilic surfaces was investigated, showing that the interfacial strength between superhydrophilic layer and copper substrate is considerably high.展开更多
Biomedical porous Ti-15 Mo alloys were prepared by microwave sintering using ammonium hydrogen carbonate（NH4HCO3） as the space holder agent to adjust the porosity and mechanical properties. The porous Ti-15 Mo alloy...Biomedical porous Ti-15 Mo alloys were prepared by microwave sintering using ammonium hydrogen carbonate（NH4HCO3） as the space holder agent to adjust the porosity and mechanical properties. The porous Ti-15 Mo alloys are dominated by β-Ti phase with a little α-Ti phase, and the proportion of α and β phase has no significant difference as the NH4HCO3 content increases. The porosities and the average pore sizes of the porous Ti-15 Mo alloys increase with increase of the contents of NH4HCO3, while all of the compressive strength, elastic modulus and bending strength decrease. However, the compressive strength, bending strength and the elastic modulus are higher or close to those of natural bone. The surface of the porous Ti-15 Mo alloy was further modified by hydrothermal treatment, after which Na2Ti6O13 layers with needle and flake-like clusters were formed on the outer and inner surface of the porous Ti-15 Mo alloy. The hydrothermally treated porous Ti-15 Mo alloy is completely covered by the Ca-deficient apatite layers after immersed in SBF solution for 14 d, indicating that it possesses high apatiteforming ability and bioactivity. These results demonstrate that the hydrothermally treated microwave sintered porous Ti-15 Mo alloys could be a promising candidate as the bone implant.展开更多
The development of methods to produce nanoparticles with unique properties via the aerosol route is progressing rapidly. Typical characterization techniques extract particles from the synthesis process for subsequent ...The development of methods to produce nanoparticles with unique properties via the aerosol route is progressing rapidly. Typical characterization techniques extract particles from the synthesis process for subsequent offiine analysis, which may alter the particle characteristics. In this work, we use laser-vaporization aerosol mass spectrometry （LV-AMS） with 70-eV electron ionization for real-time, in-situ nanoparticle characterization. The particle characteristics are examined for various aerosol synthesis methods, degrees of sintering, and for controlled condensation of organic material to simulate surface coating/functionalization. The LV-AMS is used to characterize several types of metal nanoparticles （Ag, Au, Pd, PdAg, Fe, Ni, and Cu）. The degree of oxidation of the Fe and Ni nanoparticles is found to increase with increased sintering temperature, while the surface organic-impurity content of the metal particles decreases with increased sintering temperature. For aggregate metal particles, the organic-impurity content is found to be similar to that of a monolayer. By comparing different equivalent-diameter measurements, we demonstrate that the LV-AMS can be used in tandem with a differential mobility analyzer to determine the compactness of synthesized metal particles, both during sintering and during material addition for surface functionalization. Further, materials supplied to the particle production line downstream of the particle generators are found to reach the generators as contaminants. The capacity for such in-situ observations is important, as it facilitates rapid response to undesired behavior within the particle production process. This study demonstrates the utility of real-time, in-situ aerosol mass spectrometric measurements to characterize metal nanoparticles obtained directly from the synthesis process line, including their chemical composition, shape, and contamination, providing the potential for effective optimization of process operating parameters.展开更多
基金Project (50930005) supported by the National Natural Science Foundation of ChinaProject (U0834002) supported by the Key Programof NSFC-Guangdong Joint Funds of China+1 种基金Project (LYM09024) supported by Training Program for Excellent Young Teachers withInnovation of Guangdong University, ChinaProject (2009ZM0121) supported by the Fundamental Research Funds for the CentralUniversities of South China University of Technology,China
文摘A procedure of low temperature solid-phase sintering（LTSS） was carried out to fabricate sintered metal fibrous media（SMFM） with high specific surface area.Stainless steel fibers which were produced by cutting process were first plated with a coarse copper coating layer by electroless plating process.A low-temperature sintering process was then completed at about 800 °C for 1 h under the protection of hydrogen atmosphere.The results show that a novel SMFM with complex surface morphology and high specific surface area（0.2 m2/g） can be obtained in this way.The effect of sintering temperature on the surface morphology and specific surface area of SMFM was studied by means of scanning electron microscopy and Brunauer-Emmett-Teller.The damage of micro-structure during the sintering process mainly contributed to the loss of specific surface area of SMFM and the optimal sintering temperature was 800 °C.
基金Project (50974018) supported by the National Natural Science Foundation of China Project (108007) supported by the ScienceFoundation of Ministry of Education of China
文摘In order to examine the leaching rate of potassium chloride from the sintering dust by water,surface morphology and inner structure of the dust,especially the existing state of potassium chloride,were observed by scanning electron microscopy（SEM） and linear scanning technique via energy dispersive spectroscopy（EDS）.The characterization shows that the sintering dusts are mostly porous composites or agglomerates of the fine dust particles with size less than 10 μm,and the potassium chloride and sodium chloride particles are partly covered by other water insoluble matters in the dust which consist of elements iron,calcium and etc.Exposure of potassium chloride in the agglomerated dust matrix of this kind suggests that the leaching can be simply perceived as the dissolution of water soluble matters in the dust.On-line monitor of specific electrical conductivity of the leaching system verifies the prediction that leaching kinetics of potassium chloride from the sintering dust fits dissolution model well.Leaching equilibrium can be reached within 5 min with potassium leaching ratio more than 95%.
基金Supported by the National-Basic Research Program of China （2003CB615707） and the National Natural Science Foundation of China （20636020）.
文摘The effects of sintering atmosphere on the properties of symmetric TiO2 membranes are studied with regard to sintering behavior, porosity, mean pore size, surface comPosition. and surface charge properties. The exerimental results show that the symmetric TiO2 membranes display better sintering activity in the air than in argon, and the mean pore diameters and porosities of the membrane sintered in argon are higher than those of the membrane sintered in the air at the same temperature. The surface compositions of the symmetric TiO2 membrane sintered in the air and in argon at different temperatures, as studied by X-ray photoelectron spectroscopy, are discussed in terms of their chemical composition, with particular emphasis on the valence state of the titanium ions. The correlation between the valence state of the titanium ions at the surface and the surface charge properties is examined.It is found that the presence of Ti^3＋, introduced at the surface of the symmetric TiO2 membranes by sintering in a lower partial pressure of oxygen, is related to a significant decrease in the isoelectric point. TiO2 with Ti^4＋ at the interface has an isoelectric point of 5.1, but the non-stoichiometric TiO2-x with Ti^3＋ at the interface has a lower isoelectric point of 3.6.
基金Supported by the National Natural Science Foundation of China(51275180)the Fundamental Research Funds for the Central Universities(2013ZM0003)the Doctorate Dissertation Funds of Guangdong Province(sybzzxm 201213)
文摘Superhydrophilic surfaces were fabricated on copper substrates by an electrochemical deposition and sintering process. Superhydrophobic surfaces were prepared by constructing micro/nano-structure on copper substrates through an electrochemical deposition method. Conversion from superhydrophobic to superhydrophilic was obtained via a suitable sintering process. After reduction sintering, the contact angle of the superhydrophilic surfaces changed from 155° to 0°. The scanning electron microscope （SEM） images show that the morphology of superhydrophobic and superhydrophilic surfaces looks like corals and cells respectively. The chemical composition and crystal structure of these surfaces were examined using energy dispersive spectrometry （EDS） and X-ray diffraction （XRD）. The results show that the main components on superhydrophobic surfaces are Cu, Cu2O and CuO, while the superhydrophilic surfaces are composed of Cu merely. The crystal structure is more inerratic and the grain size becomes bigger after the sintering. The interracial strength of the superhydrophilic surfaces was investigated, showing that the interfacial strength between superhydrophilic layer and copper substrate is considerably high.
基金supported by the National Natural Science Foundation of China (51101085)the Aeronautical Science Foundation of China (2015ZF56027)+2 种基金the Natural Science Foundation of Jiangxi Province (2016BAB206109)the Science and Technology Support Plan Project of Jiangxi Province (20151BBG70039)the Science and Technology Project of Jiangxi Province Education Department (GJJ150721)
文摘Biomedical porous Ti-15 Mo alloys were prepared by microwave sintering using ammonium hydrogen carbonate（NH4HCO3） as the space holder agent to adjust the porosity and mechanical properties. The porous Ti-15 Mo alloys are dominated by β-Ti phase with a little α-Ti phase, and the proportion of α and β phase has no significant difference as the NH4HCO3 content increases. The porosities and the average pore sizes of the porous Ti-15 Mo alloys increase with increase of the contents of NH4HCO3, while all of the compressive strength, elastic modulus and bending strength decrease. However, the compressive strength, bending strength and the elastic modulus are higher or close to those of natural bone. The surface of the porous Ti-15 Mo alloy was further modified by hydrothermal treatment, after which Na2Ti6O13 layers with needle and flake-like clusters were formed on the outer and inner surface of the porous Ti-15 Mo alloy. The hydrothermally treated porous Ti-15 Mo alloy is completely covered by the Ca-deficient apatite layers after immersed in SBF solution for 14 d, indicating that it possesses high apatiteforming ability and bioactivity. These results demonstrate that the hydrothermally treated microwave sintered porous Ti-15 Mo alloys could be a promising candidate as the bone implant.
文摘The development of methods to produce nanoparticles with unique properties via the aerosol route is progressing rapidly. Typical characterization techniques extract particles from the synthesis process for subsequent offiine analysis, which may alter the particle characteristics. In this work, we use laser-vaporization aerosol mass spectrometry （LV-AMS） with 70-eV electron ionization for real-time, in-situ nanoparticle characterization. The particle characteristics are examined for various aerosol synthesis methods, degrees of sintering, and for controlled condensation of organic material to simulate surface coating/functionalization. The LV-AMS is used to characterize several types of metal nanoparticles （Ag, Au, Pd, PdAg, Fe, Ni, and Cu）. The degree of oxidation of the Fe and Ni nanoparticles is found to increase with increased sintering temperature, while the surface organic-impurity content of the metal particles decreases with increased sintering temperature. For aggregate metal particles, the organic-impurity content is found to be similar to that of a monolayer. By comparing different equivalent-diameter measurements, we demonstrate that the LV-AMS can be used in tandem with a differential mobility analyzer to determine the compactness of synthesized metal particles, both during sintering and during material addition for surface functionalization. Further, materials supplied to the particle production line downstream of the particle generators are found to reach the generators as contaminants. The capacity for such in-situ observations is important, as it facilitates rapid response to undesired behavior within the particle production process. This study demonstrates the utility of real-time, in-situ aerosol mass spectrometric measurements to characterize metal nanoparticles obtained directly from the synthesis process line, including their chemical composition, shape, and contamination, providing the potential for effective optimization of process operating parameters.
