超洁净煤制备过程中矿物质的反应热力学特性

为提高不同煤中矿物质的脱除效率,采用AMICS系统对5种煤的矿物组成进行分析。针对煤中主要矿物质,分析了化学方法制备超洁净煤过程中不同矿物质的反应历程。采用HSC Chemistry热力学数据库软件计算了超洁净煤制备过程中主要矿物质的反应热力学数据(ΔH、ΔS和ΔG)及平衡常数K,判定温度对相关矿物溶出反应的影响。结果表明,煤中矿物主要包括高岭石、白云石、黄铁矿、石英和白云石等。不同煤中矿物成分不同,应根据矿物成分及热力学特性,调整化学法脱除煤中矿物质的反应温度和酸碱用量,提高矿物质脱除效率,制备高纯度UCC。其中,煤中的赤铁矿和方解石易与硫酸反应,较易脱除;煤中高岭石、硅石、铝土矿、黄铁矿的碱液消解反应需适当提高温度和碱液用量,提高矿物质转化率。

Mechanical Properties and Thermal Shock Resistance of SrAl_(2)Si_(2)O_(8) Reinforced BN Ceramic Composites

Hexagonal boron nitride(h-BN)ceramics have become exceptional materials for heat-resistant components in hypersonic vehicles,owing to their superior thermal stability and excellent dielectric properties.However,their densification during sintering still poses challenges for researchers,and their mechanical properties are rather unsatisfactory.In this study,SrAl_(2)Si_(2)O_(8)(SAS),with low melting point and high strength,was introduced into the h-BN ceramics to facilitate the sintering and reinforce the strength and toughness.Then,BN-SAS ceramic composites were fabricated via hot press sintering using h-BN,SrCO_(3),Al_(2)O_(3),and SiO_(2) as raw materials,and effects of sintering pressure on their microstructure,mechanical property,and thermal property were investigated.The thermal shock resistance of BN-SAS ceramic composites was evaluated.Results show that phases of as-preparedBN-SAS ceramic composites are h-BN and h-SrAl_(2)Si_(2)O_(8).With the increase of sintering pressure,the composites’densities increase,and the mechanical properties shew a rising trend followed by a slight decline.At a sintering pressure of 20 MPa,their bending strength and fracture toughness are(138±4)MPa and(1.84±0.05)MPa·m^(1/2),respectively.Composites sintered at 10 MPa exhibit a low coefficient of thermal expansion,with an average of 2.96×10^(-6) K^(-1) in the temperature range from 200 to 1200℃.The BN-SAS ceramic composites prepared at 20 MPa display higher thermal conductivity from 12.42 to 28.42 W·m^(-1)·K^(-1) within the temperature range from room temperature to 1000℃.Notably,BN-SAS composites exhibit remarkable thermal shock resistance,with residual bending strength peaking and subsequently declining sharply under a thermal shock temperature difference ranging from 600 to 1400℃.The maximum residual bending strength is recorded at a temperature difference of 800℃,with a residual strength retention rate of 101%.As the thermal shock temperature difference increase,the degree of oxidation on the ceramic surface and cracks due to thermal stress are also increased gradually.

Effect of hot working on microstructure and mechanical properties of TC11/Ti_2AlNb dual-alloy joint welded by electron beam welding process

The influence of hot working on the microstructures of TC11/Ti2 Al Nb dual-alloy joints welded by electron beam welding(EBW) process was investigated. The tensile tests were performed at room temperature for specimens before and after thermal exposure. The results show that the fusion zone of TC11/Ti2 Al Nb dual-alloy joint welded by EBW is mainly composed of β phase. After deformation and heat treatment, the grain boundaries of the as-cast alloy are broken and the fusion zone mainly consists of β, α2and α phases. The fusion zone performs poor property in the tensile test. Specimens before and after thermal exposure all fail in this area under different deformation conditions. The ultimate tensile strength of specimens after heat treatment is up to 1190 MPa at room temperature. The joints by water quenching after deformation have better plasticity with an elongation up to 4.4%. After thermal exposure at 500 °C for 100 h, the tensile strength of the specimen slightly rises while the ductility changes a little. SEM observation shows that the fracture mechanism is predominantly transgranular under different deformation conditions.

Effect of Heat Stress on Photosynthetic Characteristics of Different Green Organs of Winter Wheat During Grain-filling Stage

Four winter wheat (Triticum aestivum L.) varieties ('JD 8', 'Jing 411','Centurk' and 'Tam 202') were used to study the effect of heat stress on photosynthetic characteristics of flag leaf blade, nag leaf sheath, peduncle, glume, lemma and awn during grain-filling stage. The results showed that heat acclimation during grain-filling stage increased thermotolerance of wheat with significant differences among different green organs. During heat stress, the decreases of the efficiency of primary light energy conversion (F-v/F-m) of PS II and pigment (chlorophyll and carotenoid) content were much slower in peduncle, flag leaf sheath and glume than in nag leaf blade, lemma and ann; and the percentage of decrease in net photosynthetic rate (P-n) of ear was lower than that of the nag leaf blade. The measured photosynthetic parameters (F-v/F-m, P-n and pigment content) of 'JD 8', a relatively heat tolerant variety, declined more slowly than those of the other three varieties during the whole heat stress period.

Microstructures and mechanical properties of 2024Al/Gr/SiC hybrid composites fabricated by vacuum hot pressing

The 2024Al/Gr/SiC hybrid composite plates with 5%-10% SiC particles （volume fraction） and 3%-6% flaky graphite （Gr） （volume fraction） were fabricated by vacuum hot pressing and hot extrusion processing. The effects of SiC and Gr on the microstructures and mechanical properties of the composites aged at 160, 175 and 190℃ were studied by optical microscopy, scanning electron microscopy （SEM）, and hardness and tensile tests. The results indicate that the SiC particles have a more obvious effect on accelerating the aging response as compared with the Gr. Both the tensile strength and elongation are reduced by the Gr and SiC particles added into the matrix, while the Gr has a more negative influence on the elongation than the SiC particles. The tensile strength （ab）, yield stress （as） and elongation （δ） of the 2024Al/3Gr/10SiC composite aged at 165℃ for 8 h are 387 MPa, 280.3 MPa and 5.7%, respectively. The hybrid composites are characterized by ductile fracture, which is associated with the ductile fracture of the matrix and the tearing of the interface between the matrix and the particles.

Effect of Si and Ti on dynamic recrystallization of high-performance Cu-15Ni-8Sn alloy during hot deformation

Effect of Si and Ti on dynamic recrystallization(DRX)of Cu-15Ni-8 Sn alloy was studied using hot compression tests over deformation temperature range of 750-950℃and strain rate range of 0.001-10 s^-1.The results show that the dynamic recrystallization behavior during hot deformation is significantly affected by the trace elements of Si and Ti.The addition of Si and Ti promotes the formation of Ni16Si7Ti6 particles during hot deformation,which promotes the nucleation of dynamic recrystallization by accelerating the transition from low-angle boundaries(LABs)to high-angle boundaries(HABs).Ni16Si7Ti6 particles further inhibit the growth of recrystallized grains through the pinning effect.Based on the dynamic recrystallization behavior,a processing map of the alloy is built up to obtain the optimal processing parameters.Guided by the processing map,a hot-extruded Cu-15 Ni-8Sn alloy with a fine-grained microstructure is obtained,which shows excellent elongation of 30%and ultimate tensile strength of 910 MPa.

Thermodynamic properties and heat capacity of Ru metal in HCP,FCC,BCC and liquid state

Isometric heat capacity cv and isobar heat capacity cp of Ru metal in HCP,FCC,BCC and liquid state were calculated by using pure element systematic theory.The results are in good agreement with joint army-navy-air force(JANAF) experimental value and the calculation result by first-principle(FP) method.But the results have great differences in contrast to Scientific Group Thermodata Europe(SGTE) database.The cause is found that it cannot neglect the electron devotion to heat capacity to adjust cp in one-atom(OA) method.The disparity between OA method and SGTE database was discussed.The main cause is that OA method adopts the crosspoint with iso-Ec-line and iso-a-line in hybritriangle to determine the properties,but SGTE database is obtained by extrapolation from activity measurements and critical assessment of data from a large number of binary system.Thermodynamic properties of Ru metal in HCP,FCC,BCC and liquid state,such as entropy S,enthalpy H and Gibbs energy G were calculated.Therefore,the full description of thermodynamic properties from 0 K to random temperature is implemented.

Analysis of safety characteristics of coal-based aviation kerosene

The risk and thermal safety characteristics of GX kerosene,HX kerosene and WX kerosene are studied.Firstly,the explosion lower limits of three kinds of kerosene steams are tested by using the self-made explosion limit measuring system.Then differential scanning calorimeter(DSC)is employed to perform linear heating experiment on kerosene to analyze its thermal decomposition characteristics.The pyrolysis kinetic parameters of three kinds of kerosene are calculated based on the thermal dynamic methods.The experimental results show that the flash point and lower explosion limit of GX kerosene are relatively low.The DSC test shows that the lowest initial decomposition temperature of HX kerosene is 116.5℃.According to pyrolysis kinetics calculation,the T_(D24) and apparent activation energy of HX kerosene are the minimum.ARC test shows that GX kerosene has the worst thermal stability under the adiabatic condition.The high temperature stabilities of the three kinds of kerosene all meet the requirements.On the whole,GX kerosene has the highest hazard,and HX kerosene has the lowest thermal safety.The accumulation of heat should be prevented during the storage and transportation of kerosene.This study provides the crucial safety characteristics data of coal-based aerospace kerosene-based,and provides technical support for engine reliability growth and performance improvement.

Physical and mechanical properties of Beishan granite after different high temperature treatments

In China,Beishan granite is chosen as a potential host surrounding rock of a high-level radioactive waste(HLW)repository.For this research,Beishan granite specimens were heated up to 300℃,400℃ and 500℃,respectively.And conventional triaxial compression tests were conducted after cooling down the samples.The results show that after 300℃,400℃ and 500℃ heating treatment,the diameter of samples increases by 0.066%,0.143%and 0.409%,respectively,which is a little larger than the axial length changes.Mechanical tests show that peak strength increases slightly with increasing temperature.However,the dilatancy threshold is lower than that observed for samples which have not experienced heating treatment.Peak strain and dilatancy threshold strain show a strong temperature dependence.The higher the temperature,the greater the strain.Furthermore,increasing temperature has negative influence on threshold elastic modulus E_(c) and tangent elastic modulus E_(t).Poisson ratio decreases when temperature increases from 300℃ to 500℃,but it is still larger than that observed for samples which have not experienced heating treatment.In addition,AE monitoring shows a quiet period in the initial loading stage,which proves that the micro cracks are closed during heating and contribute to the increase of peak strength.

Calculation and Verification for the Thermodynamic Data of 3CaO·3Al_2O_3·CaSO_4

Calcium sulfoaluminate,3CaO·3Al2O3·CaSO4,has been widely recognized in the realms of high-temperature combustion and cement chemistry.However,the lack of relevant thermodynamic data limits the progress of its research and development.Through comparative calculations using several different approaches,we obtain the thermochemical properties of 3CaO·3Al2O3·CaSO4 in this work,such as its standard formation enthalpy,Gibbs free en- ergy of formation,entropy,and molar heat capacity.With these fundamental data,thermodynamic calculations become possible for reactions involving this mineral.It is found that some reactions proposed in literature to generate this mineral may not proceed thermodynamically.

Thermal Stability and Thermal Decomposition Kinetics of 1-Butyl-3-methylimidazolium Dicyanamide

Thermal stability and thermal decomposition kinetics of 1-butyl-3-methylimidazolium dicyanamide ([bmin+][N(CN) ]2-) were investigated using both isothermal and non-isothermal thermogravimetric analyses (TGA) under high pure nitrogen as carrier gas. The long-term thermogravimetric studies revealed that the highest temperature used should be 110 °C, at which [bmin+][N(CN)2-] lost less than 10% by mass in 10 hours. The non-isothermal activation energy values determined using Friedman and ASTM methods were (150±13) and (147±2) kJ·mol –1 , respectively. Multivariate non-linear-regression methods showed that expanded Fn and CnB models were the best fit models with highest correlation coefficient of 0.9994, and the apparent activation energies were consistent with iso-conversional methods.

Thermodynamic optimization for a quantum thermoacoustic refrigeration micro-cycle

A model of quantum thermoacoustic refrigeration micro-cycle(QTARMC)is established in which heat leakage is considered.A single particle contained in a one-dimensional harmonic potential well is studied,and the system consists of countless replicas.Each particle is confined in its own potential well,whose occupation probabilities can be expressed by the thermal equilibrium Gibbs distributions.Based on the Schrodinger equation,the expressions of coefficient of performance(COP)and cooling rate for the refrigerator are obtained.Effects of heat leakage on the optimal performance are discussed.The optimal performance region of the refrigeration cycle is obtained by the using ofΩobjective function.The results obtained can enrich the thermoacoustic theory and expand the application of quantum thermodynamics.

Mechanical and thermo-physical properties of rapidly solidified Al-50Si-Cu(Mg) alloys for thermal management application

Al-high Si alloys were designed by the addition of Cu or Mg alloying elements to improve the mechanical properties. It is found that the addition of 1 wt.% Cu or 1 wt.% Mg as strengthening elements significantly improves the tensile strength by 27.2% and 24.5%, respectively. This phenomenon is attributed to the formation of uniformly dispersed fine particles(Al2Cu and Mg2Si secondary phases) in the Al matrix during hot press sintering of the rapidly solidified(gas atomization) powder. The thermal conductivity of the Al-50 Si alloys is reduced with the addition of Cu or Mg, by only 7.3% and 6.8%, respectively. Therefore, the strength of the Al-50 Si alloys is enhanced while maintaining their excellent thermo-physical properties by adding 1% Cu(Mg).

Thermodynamic assessment of ZnO-SiO_2 system

ZnO-containing slags are common in pyrometallurgical processing of the base metals and steel.This caused the interest to the thermodynamics of the ZnO-SiO2 system.A complete literature survey,critical evaluation of the available experimental data and a thermodynamic optimization of the phase equilibria and thermodynamic properties of the system ZnO-SiO2 at 1.013×105 Pa are presented.The molten oxide was described as an associate solution.The properties of liquid were reassessed and enthalpy term of the Gibbs energy of solid Zn2SiO4 was re-fitted to be compatible with the new data in the willemite primary phase field.The thermodynamic data set agrees well with the recent experimental observations.It can be used for predicting,e.g.,the thermodynamic properties and the domains of the phase diagram,like critical point of the liquid miscibility gap,with a better accuracy than using the previous assessments.A set of optimized model parameters were obtained,reproducing the reliable thermodynamic and phase equilibrium data within their experimental errors from 298 K to liquidus temperatures,over the entire composition range.The created database can be used in a Gibbs energy minimization software to calculate the thermodynamic properties and the phase diagram sections of interest.

Entropy Analysis of NH_3/H_2O Absorption-Compression Heat Pump

The absorption-compression heat pump （ACHP） has been considered as an effective approach to recover and utilize low-grade heat sources. In the present study, the first and second law thermodynamic analyses of the ACHP with NH3/H20 as working fluid were performed. Thermodynamic properties of each point and heat transfer rate of each component in the cycle under basic operation conditions were calculated from the first law analysis. Following the second law of thermodynamics, the entropy generation of each component and the total entropy generation of the system were obtained. The effect~ of the heating temperature, heat source temperature, and compression ratio on the coefficient of performance （COP） and the total entropy generation （ STot ） of the system were examined. The results show that the increase in COP corresponds to a decrease in STot, and vice versa; besides, for certain operating conditions, an optimum compression ratio in the NH~/H20 ACHP exists.

Hot workability of cast and wrought Ni-42Cu alloy through hot tensile and compression tests

In order to analyze the flow behavior and workability of Ni-42Cu in cast and wrought conditions, hot deformation tests were performed at temperatures and strain rates within the ranges of 900-1150 ℃ and 0.001-1 s^-1, respectively. Tensile tests showed a “hot ductility trough” at 950 ℃ for both alloys. The drop in hot ductility was more considerable in the cast alloy because of the sluggish dynamic recrystallization. The hot ductility drop and grain boundary cracking, particularly in the cast alloy, were attributed to the segregation of detrimental atoms to the boundaries. It was shown that the hot ductility of the wrought alloy could be improved with increasing strain rate. It was associated with increasing the fraction of dynamic recrystallization at higher strain rates. This finding corroborated the change in the mechanism of dynamic recrystallization with strain rate. The strain rate sensitivity and instability parameters calculated for the wrought alloy showed that the material is prone to strain localization at low temperatures, i.e., 950-1050 ℃, and high strain rates of 0.1 and 1 s-1. Based on the tensile and compression tests, the best temperature range for a desirable hot workability was introduced as 1050-1150 ℃.

Thermogravimetric characteristics and different kinetic models for medical waste composition containing polyvinyl chloride-transfusion tube

Thermogravimetric study of medical transfusion tube （MTT） waste containing polyvinyl chloride （PVC） was carried out using the thermogravimetric analyser （TGA） with N2, at different heating rates of 5, 10, 20, 30, 50 ℃/min. The purpose is to obtain pyrolysis characteristics and kinetic parameters of medical waste. The experimental results indicate that the pyrolysis behavior of the MTT sample is in agreement with its main ingredient of PVC, appearing two stair stepping stages. The influence of the additives in MTT on pyrolysis behavior was also revealed, which could improve MTT pyrolysis at lower temperature in the first stage, and cause obvious unsmoothness and asymmetry of the second DTG peak. Four n-order kinetic models of Coats-Redfern, Ozawa, Kissinger and Freeman-carroll were used to get the kinetic parameters. Furthermore, a novel ＂two-step four-reaction model＂ was established to simulate the whole continuous process. The different methods and the kinetic parameters thus obtained were discussed and compared with each other in literatures. The reasons of deviation among kinetic values were tried to be elucidated. The new established model could more satisfactorily describe the pyrolysis process of MTT, being more mechanistic and conveniently serving for the engineering.

Elasticity under pressure and thermal property of Mg2La from first-principles calculations

The elastic properties, thermodynamic and electronic structures of Mg_2La were investigated by using first-principles. The calculated results show that pressure affects the elastic constants of C_(11) more than that of C_(12) and C_(44). Specifically, higher pressure leads to greater bulk modulus(B), shear modulus(G), and elastic modulus(E). We predict B/G and anisotropy factor A based on the calculated elastic constants. The Debye temperature also increases with increasing pressure. Based on the quasi-harmonic Debye model, we examined the thermodynamic properties. These properties include the normalized volume(V/V_0), bulk modulus(B), heat capacity(C_v), thermal expansion coefficient(α), and Debye temperature(■). Finally, the electronic structures associated with the density of states(DOS) and Mulliken population are analyzed.

Pyrolytic characteristics and kinetics of the marine green tide macroalgae, Enteromorpha prolifera

The marine macroalgae Enteromorpha prolifera was one of the main algal genera that occurred in the widespread green tides in Qingdao, China, during the summers of 2007, 2008 and 2010. It is thus a plentiful source of biomass and could be used as a biofuel. In this study, the pyrolytic characteristics and kinetics of E. prolifera were investigated using thermogravimetric analysis (TGA) method. Cornstalk and sawdust were used as comparisons. Pyrolytic characteristics were studied using TG-DTG (thermogravimetry-derivative thermogravimetry) curves. Three stages in the pyrolytic process were determined: dehydration, dramatic weight loss and slow weight loss. E. prolifera was pyrolyzed at a lower initial temperature than the two terrestrial biomass forms. The apparent activation energy values for the three types of biomass were calculated and the mechanism functions were determined using 16 different mechanism functions, frequently used in thermal kinetics analysis. Activation energy values varied with mechanism function and the range of activation energy values for E. prolifera, cornstalk, and sawdust were 25-50 kJ/mol, 60-90 kJ/mol and 120-155 kJ/mol, respectively. This indicates that E. prolifera has low thermal stability for pyrolysis and good combustion characteristics.

Thermodynamic Properties of Caprolactam Ionic Liquids

A series of caprolactam ionic liquids(ILs) containing incorporated halide anions were synthesized.Their physical properties,such as melting points,heats of fusion and heat capacities,were measured by differential scanning calorimeter(DSC).The results indicate that these ionic liquids exhibit proper melting points,high value of heats of fusion,and satisfying heat capacities which are suitable for thermal energy storage applications.