均匀热压强时径向本征函数的研究

应用半解析方法,数值计算了不同均匀热压强时,径向本征函数随圆柱等离子体半径和粘度的演化规律。数值模拟结果表明:当等离子体热压强均匀时,压强对长波模式磁流体系统的径向本征函数基本无影响;短波模式时,均匀等离子体热压强对径向本征函数的极值大小和极值所处的位置均有明显影响,说明径向本征函数对波长的变化比较敏感。

可控压强水热合成Cu_2O及其光吸收性质研究

本论文采用可控压强水热法,以Cu(CH_3COO)_2为前驱物,200℃下,在一定压强范围内合成出束状和塔状结构形貌的Cu_2O.考察了前驱物的浓度,初始压强等条件对产物形貌的影响.实验结果说明,反应压强对氧化亚铜的形貌的形成起到关键的作用.随压强的提高所得Cu_2O的光吸收增强,吸收峰的位置随压强的提高而发生明显红移.

两段炉用型煤热强度的研究

本文研究了城市两段炉用型煤的热强度特性曲线,结果表明,在干馏段型煤热强度的变化受煤种的影响很大.对于粘结性大的煤种,用普通工艺生产型煤,其热强度变化大,热强度的最小值也小,难以满足两段炉的要求.而用活性粘土作为型煤的粘结剂并添加一定量的焦粉,则是“破粘”和防胀裂的有效途径.

型煤在两段炉气化段内热强度的变化规律

本文阐述了在两段炉气化段内，型煤热强度的变化规律和粘结剂种类对型煤热强度的影响。

磁流体径向本征函数的演化规律

应用傅里叶变换,将线性化的理想磁流体方程组转化为一个关于径向本征函数的二阶常微分方程。通过求解此方程,数值模拟了角向模数m=2时,圆柱磁流体径向本征函数在不同热压强时随波数和增长率的演化规律。数值模拟结果表明径向本征函数对波长的变化比较敏感,在短波模式有一定波动,长波时不受增长率的影响。此结果有利于加深对高角向模数不稳定性的理解,同时也验证了半解析方法解决磁流体问题的有效性和简洁性。

Influence of FeCrAl fiber on microstructure and mechanical properties of FeCrAl(f)/HA composites

FeCrAl fiber-reinforced hydroxyapatite（HA） biocomposites（FeCrAl（f）/HA） were fabricated by the hot pressing technique.The metallographic microscopy,X-ray diffractometry,scanning electron microscopy（SEM） and energy dispersive spectroscopy（EDS） were used to observe and analyze the microstructure and composition of FeCrAl（f）/HA composites,respectively.The mechanical properties of FeCrAl（f）/HA composites were measured by the three-point-bending test.The results show that the composite can be reinforced by FeCrAl fiber and enhanced gradually,and then declined with the increase of the content of FeCrAl fiber（0-11%,volume fraction） in the whole range of experiments.Both the HA matrix and FeCrAl fiber integrate very tightly and bit into each other very deeply and counter-diffusion takes place to some extent at two-phase interface.The optimum parameters of FeCrAl（f）/HA composite are diameter of 22 μm,length of 1-2 mm and of volume faction of about 7% for FeCrAl fibers.

Relationship between Rice Planthopper Occurrence Area in China and Atmospheric Circulation Indices

[Objective] This study aimed to establish models based on atmospheric cir- culation indices for forecasting the area attacked by rice planthopper every year, and to provide guide for preventing and controlling planthopper damage. [Method] The data related to rice planthopper occurrence and atmospheric circulation were collected and analyzed with the method of stepwise regression to establish the prediction models. [Result] The factors significantly related to the area attacked by rice plan-thopper were selected. Two types of prediction models were established. One was for Sogatella furcifera （Horvath）, based on Atlantic-Europe circulation pattern W in October in that year, Pacific polar vortex area index in October in that year, North America subtropical high index in August in that year, Atlantic-Europe circulation pattern W in June in that year, northern boundary of North America subtropical high in February in that year, Atlantic-Europe polar vortex intensity index in October in that year and Asia polar vortex intensity index in November in the last year; the other type of prediction models were for Nilaparvata lugens （Stal）, based on the Eastern Pacific subtropical high intensity index in July in that year, northern hemi- sphere polar vortex area index in October in the last year, Asia polar vortex strength index in November in the last year, north boundary of North America-At- lantic subtropical high in September in that year, north boundary of North Africa-At- lantic-North America subtropical high in January in that year, sunspot in September of the last year and eastern Pacific subtropical high area index in September in that year. [Conclusion] With the stepwise regression, the forecasting equations of the rice planthopper occurrence established based on the atmospheric circulation indices could be used for actual forecast.

Oxidation behavior of C/C composites with SiC/ZrSiO_4-SiO_2 coating

A SiC/ZrSiO4？SiO2 （SZS） coating was successfully fabricated on the carbon/carbon （C/C） composites by pack cementation, slurry painting and sintering to improve the anti-oxidation property and thermal shock resistance. The anti-oxidation properties under different oxygen partial pressures （OPP） and thermal shock resistance of the SZS coating were investigated. The results show that the SZS coated sample under low OPP, corresponding to the ambient air, during isothermal oxidation was 0.54% in mass gain after 111 h oxidation at 1500 ° C and less than 0.03% in mass loss after 50 h oxidation in high OPP, corresponding to the air flow rate of 36 L/h. Additionally, the residual compressive strengths （RCS） of the SZS coated samples after oxidation for 50 h in high OPP and 80 h in low OPP remain about 70% and 72.5% of those of original C/C samples, respectively. Moreover, the mass loss of SZS coated samples subjected to the thermal cycle from 1500 ° C in high OPP to boiling water for 30 times was merely 1.61%.

Formability and strengthening mechanism of AA6061 tubular components under solid granule medium internal high pressure forming

A new technological process of tube forming was developed, namely solution treatment → granule medium internal high pressure forming → artificial aging. During this process, the mechanical properties of AA6061 tube can be adjusted by heat treatment to satisfy the process requirements and the processing method can also be realized by granule medium internal high pressure forming technology with the features of convenient implementation, low requirement to equipment and flexible design in product. Results show that, at a solution temperature of 560 ℃ and time of 120 min, the elongation of AA6061 increases by 313%, but the strength and the hardness dramatically decrease. At an aging temperature of 180 ℃ and time of 360 min, the strength and hardness of AA6061 alloy are recovered to the values of the as-received alloy. The maximum expansion ratio（MER） of AA6061 tube increases by 25.5% and the material properties of formed tube reach the performances of raw material.

Fabrication and mechanical properties of Ti_(2)AlC/TiAl composites with co-continuous network structure

Ti_(2)AlC/TiAl composites with different volume fractions were prepared by hot pressing technology,and their reinforced structural characteristics and mechanical properties were evaluated.The results showed that when the reinforced phase volume fraction of Ti_(2)AlC was 20%,three-dimensional interpenetrating network structures were formed in the composites.Above 20%,Ti_(2)AlC phase in the composites accumulated and grew to form thick skeletal networks.The microplastic deformation behavior of Ti_(2)AlC phase,such as kink band and delamination,improved the fracture toughness of the composites.Comparative analysis indicated that the uniform and small interconnecting network structures could further reinforce the composites.The bending strengths of composites prepared with 20 vol.%Ti_(2)AlC reached(900.9±45.0)MPa,which was 25.5% higher than that of TiAl matrix.In general,the co-continuous Ti_(2)AlC/TiAl composite with excellent mechanical properties can be prepared by powder metallurgy method.

Effects of heat treatment on phase contents and mechanical properties of infiltrated B_4C/2024Al composites

The B4C/2024Al composites were successfully produced by pressureless infiltration method, and the effects of heat treatment on phase content and mechanical properties were investigated by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and mechanical properties testing. The results show that phases of BnC/2024Al composites include B4C, Al, Al3BC, AlB2 and Al2Cu. The phase species remain unchanged; however, the phase content of the composites changes significantly after heat treatment at the temperature of 660, 700, 800 or 900 ℃ for 12, 24 or 36 h. It is found that the heat treatment results in not only considerable enhancement in hardness, but also reduction in bending strength of the composites. Heat treatment at 800 ℃ for 36 h does best to hardness of the composites, while at 700 ℃ for 36 h it is the most beneficial to their comprehensive mechanical properties.

Flow stress behavior and processing map of extruded 7075Al/SiC particle reinforced composite prepared by spray deposition during hot compression

Hot compression tests of the extruded 7075Al/15%SiC (volume fraction) particle reinforced composite prepared by spray deposition were performed on Gleeble?1500 system in the temperature range of 300?450 °C and strain rate range of 0.001?1 s?1. The results indicate that the true stress?true strain curve almost exhibits rapid flow softening phenomenon without an obvious work hardening, and the stress decreases with increasing temperature and decreasing strain rate. Moreover, the stress levels are higher at temperature below 400 °C but lower at 450 °C compared with the spray deposited 7075Al alloy. Superplastic deformation characteristics are found at temperature of 450 °C and strain rate range of 0.001?0.1 s?1 with corresponding strain rate sensitivity of 0.72. The optimum parameters of hot working are determined to be temperature of 430?450 °C and strain rate of 0.001?0.05 s?1 based on processing map and optical microstructural observation.

Microstructural evolution and mechanical properties of an ultrahighstrength Al-Zn-Mg-Cu alloy via powder metallurgy and hot extrusion

In this work,a novel ultrahigh-strength Al-10Zn-3.5Mg-1.5Cu alloy was fabricated by powder metallurgy followed by hot extrusion.Investigations on microstructural evolution and mechanical properties of the fabricated samples were carried out.The results show that the grain size of sintered samples matches with the powder particles after ball milling.The relative densities of sintered and hot extruded samples reach 99.1%and 100%,respectively.Owing to the comprehensive mechanism of grain refinement,aging and dispersion strengthening,the ultimate tensile strength,yield strength and elongation of the Al-10Zn-3.5Mg-1.5Cu alloy after hot extrusion and subsequent heat treatment achieve 810 MPa,770 MPa and 8%,respectively.

Thermal contact conductance at continuous roll-casting interface

The effects of surface roughness, strain rate, friction coefficient and pressure on real contact area were analyzed based on the research of Stupkiewicz. The real contact area model taking account of the effect of friction and deformation of material was obtained. The model of contact conductance at the rolling interface was obtained by integrating the specific feature of heat transfer through the interface of continuous roll-casting. The results indicate that the real contact area increases obviously when the material is under yield, and the real contact area varies inversely with surface roughness, whereas it varies exponentially with friction coefficient, strain rate and pressure, and the power factor depends on strain rate.

Mechanism of high pressure roll grinding on compression strength of oxidized hematite pellets

The mechanism of high pressure roll grinding on improvement of compression strength of oxidized hematite pellets was researched by considering their roasting properties. The results indicate that oxidized hematite pellets require higher preheating temperature and longer preheating time to attain required compression strength of pellets compared with the common magnetite oxidized pellets. It is found that when the hematite concentrates are pretreated by high pressure roll grinding （HPRG）, the compression strengths of preheated and roasted oxidized hematite pellets get improved even with lower preheating and roasting temperatures and shorter preheating and roasting time. The mechanism for HPRG to improve roasting properties of oxidized pellets were investigated and the cause mainly lies in the increase of micro-sized particles and the decrease of dispersion degree for hematite concentrates, which promotes the hematite concentrate particles to be compacted, the solid-phase crystallization, and finally the formation of Fe203 bonding bridges during subsequent high temperature roasting process.

Thermal performance of tubular heat exchanger with multiple twisted-tape inserts

The paper presents an experimental investigation on enhanced heat transfer and pressure loss characteristics by using single, double, triple, and quadruple twisted-tape inserts in a round tube having a uniform heat-fluxed wall. The investigation has been conducted in the heat exchanger tube inserted with various twisted-tape numbers for co- and counter-twist arrangements for the turbulent air flow, Reynolds number （Re） from 5300 to 24000. The typical single twisted-tape inserts at two twist ratios, y/w = 4 and 5, are used as the base case, while the other multiple twisted-tape inserts are aty/w = 4 only. The experimental results of heat transfer and pressure drop in terms of Nusselt number （Nu） and friction factor 00, respectively, reveal that Nu increases with the increment of Re and of twisted-tape number. The values of Nu for the inserted tube are in a range of 1.15-2.12 times that for the plain tube while f is 1.9-4.1 times. The thermal enhancement factor of the inserted tube under similar pumping power is evaluated and found to be above unity except for the single and the double co-twisted tapes. The quadruple counter-twisted tape insert provides the maximum thermal performance.

Dynamic compressive strength and failure mechanisms of microwave damaged sandstone subjected to intermediate loading rate

To investigate the influence of microwave heating on the dynamic behavior and failure mechanisms of rock,dynamic compression tests were conducted on microwave-irradiated sandstone specimens using a modified split Hopkinson pressure bar(SHPB)system.Experimental results show that microwave radiation can effectively weaken the compressive strength of sandstone.Rock specimens show three different failure modes under impact load:tensile failure,tensile−shear composite failure and compressive−shear failure.The dynamic Poisson’s ratio,calculated using the measured P-and S-wave velocities,is introduced to describe the deformation characteristics of sandstone.With the increase in microwave power and heating time,the Poisson’s ratio declines first and then increases slightly,and the turning point occurs at 244.6℃.Moreover,the microstructural characteristics reveal that microwave radiation produces dehydration,pore expansion,and cracking of the rock.The damage mechanisms caused by microwave radiation are discussed based on thermal stress and steam pressure inside the rock,which provides a reasonable explanation for the experimental results.

Optimization of three-dimensional boiling enhancement structure at evaporation surface for high power light emitting diode

A theoretical model of phase change heat sink was established in terms of thermal resistance network. The influence of different parameters on the thermal resistance was analyzed and the crucial impact factors were determined. Subsequently, the forming methods including ploughing-extrusion and stamping method of boiling enhancement structure at evaporation surface were investigated, upon which three-dimensional microgroove structure was fabricated to improve the efficiency of evaporation. Moreover, the crucial parameters related to the fabrication of miniaturized phase change heat sink were optimized. The heat transfer performance of the heat sink was tested. Results show that the developed phase change heat sink has excellent heat transfer performance and is suitable for high power LED applications.

Microstructure and compression properties of fine Al2O3 particles dispersion strengthened molybdenum alloy

The Mo alloys reinforced by Al2O3 particles were fabricated by hydrothermal synthesis and powder metallurgy. The microstructures of Mo-Al2O3 alloys were studied by using XRD, SEM and TEM. The results show that Al2O3 particles, existing as a stable hexagonal phase(α-Al2O3), are uniformly dispersed in Mo matrix. The ultrafine α-Al2O3 particles remarkably refine grain size and increase dislocation density of Mo alloys. Moreover, a good interfacial bonding zone between α-Al2O3 and Mo grain is obtained. The crystallographic orientations of the interface of the Al2O3 particles and Mo matrix are [111]a-Al2O3//[111]Mo and(112)a-Al2O3//(0 11)Mo. Due to the effect of secondary phase and dislocation strengthening, the yield strength of Mo-2.0 vol.%Al2O3 alloy annealed at 1200 ℃ is approximately 56.0% higher than that of pure Mo. The results confirm that the addition of Al2O3 particles is a promising method to improve the mechanical properties of Mo alloys.

Effect of heat treatment on microstructures and mechanical properties of extruded-rolled AZ31 Mg alloys

The deformation behaviors of extruded-rolled(ER)AZ31 Mg alloys with different rolling reduction and heat treatment were investigated.The results show that the accumulation of rolling reduction increases the density of twins,and refines the grain structures,which are in accordance with the enhanced strength and degraded plasticity.Tensile strength and plasticity of the alloy depend mainly on rolling reduction,while heat treatment temperature plays a more important role than heat treatment time at the same rolling reduction.With the increase of rolling reduction,the plasticity becomes more sensitive than strength on heat treatment. Recrystallization of extruded-rolled alloys will occur easily with deformation increasing,which is induced by addition of distortion energy.