The basic glass of Li2O-Al2O3-SiO2 system using P2O5 as nucleator was prepared by means of conventional melt quenching technology, and the heat-treatment process was determined by using differential thermal analysis. ...The basic glass of Li2O-Al2O3-SiO2 system using P2O5 as nucleator was prepared by means of conventional melt quenching technology, and the heat-treatment process was determined by using differential thermal analysis. The crystalline phases and the microstructure of the glass-ceramics were investigated by using X-ray diffraction and scanning electron microscopy. The results show that the glass based on Li2O-Al2O3-SiO2 oxides using P2O5 as nucleator can be prepared at lower melt temperature of 1 450 ℃ and the glass-ceramics with lower thermal expansion coefficient of 21.6×10-7 ℃-1 can also be obtained at 750 ℃. The glass-ceramics contain a few crystal phases in which the main crystal phase is β-quartz solid solution and the second crystal phase is β-spodumene solid solution. When the heat treatment temperature is not higher than 650 ℃, the transparent glass-ceramics containing β-quartz solid solution can be prepared. β-quartz solid solution changes into β-spodumene solid solution at about 750 ℃. And the appearance of the glass-ceramics changes from translucent, part opaque to complete opaque with increasing （temperature.）展开更多
Many properties of polyester filaments such as heat shrinkage, tenacity, elongation at break and etc. are greatly influenced by drawing, so post-drawing is important in downstream processing. As more and more profile ...Many properties of polyester filaments such as heat shrinkage, tenacity, elongation at break and etc. are greatly influenced by drawing, so post-drawing is important in downstream processing. As more and more profile fibers and multi-variance fibers used in textile industry, the properties of above two kinds of differential polyester filaments after drawing in different heat conditions were studied. Finally following conclusions were obtained: Firstly, the tenacity and elongation at break decreases with the rise of Tp. Secondly, the tenacity rises but the elongation at break decreases with the increase of Tb. Then, when the Tb is low, both the shrinkage in boiling water and hi hot air decreases with the rise of Tp, while, when the Tb is high, both the shrinkage rises with the rise of Tp. The last, both the shrinkage decreases with the rise of Tb.展开更多
A general research program, focusing on activated carbon fiber cloths （ACFC） and felt for environmental protection was performed. The objectives were multiple： （i） a better understanding of the adsorption mecha- ...A general research program, focusing on activated carbon fiber cloths （ACFC） and felt for environmental protection was performed. The objectives were multiple： （i） a better understanding of the adsorption mecha- nisms of these kinds of materials; （ii） the specification and optimization of new processes using these adsorbents; （iii） the modeling of the adsorption of organic pollutants using both the usual and original approaches; （iv） applications of ACFC in industrial processes. The general question was： how can activated carbon fiber cloths and felts be used in air treatment processes for the protection of environment. In order to provide an answer, different approaches were adopted. The materials （ACFC） were characterized in terms of macro structure and internal porosity. Specific studies were performed to get the air flow pattern through the fabrics. Head loss data were generated and modeled as a fi.mction of air velocity. The performances of ACF to remove volatile organic compounds （VOCs） were approached with the adsorption isotherms and breakthrough curves in various operating conditions. Regenera- tion by Joule effect shows a homogenous heating of adsorber modules with rolled or pleated layers. Examples of industrial developments were presented showing an interesting technology for the removal of VOCs, such as dichloromethane, benzene, isopropyl alcohol and toluene, alone or in a complex mixture.展开更多
The increase in the population of Tunisia and the industrial development posed with acuity during the end of the major problems. Without contribution of additional resources, water will then be likely to be done incre...The increase in the population of Tunisia and the industrial development posed with acuity during the end of the major problems. Without contribution of additional resources, water will then be likely to be done increasingly rare. The solar still is a small production system, yielding on average 2-5 L/day. In this study we propose a solar distiller assisted by a heat pump. The design of this distiller uses for the evaporation of water and its condensation two phenomena are studied Simple Solar Distiller （SSD） and Simple Solar Still Distiller Hybrid with heat Pump （SSDHP）. The performance is less than 2 L/mVday and a performance of 30% for the SSD. But the SSDHP is 12 L/m2/day, the energetic efficiency reaches 90%.展开更多
文摘The basic glass of Li2O-Al2O3-SiO2 system using P2O5 as nucleator was prepared by means of conventional melt quenching technology, and the heat-treatment process was determined by using differential thermal analysis. The crystalline phases and the microstructure of the glass-ceramics were investigated by using X-ray diffraction and scanning electron microscopy. The results show that the glass based on Li2O-Al2O3-SiO2 oxides using P2O5 as nucleator can be prepared at lower melt temperature of 1 450 ℃ and the glass-ceramics with lower thermal expansion coefficient of 21.6×10-7 ℃-1 can also be obtained at 750 ℃. The glass-ceramics contain a few crystal phases in which the main crystal phase is β-quartz solid solution and the second crystal phase is β-spodumene solid solution. When the heat treatment temperature is not higher than 650 ℃, the transparent glass-ceramics containing β-quartz solid solution can be prepared. β-quartz solid solution changes into β-spodumene solid solution at about 750 ℃. And the appearance of the glass-ceramics changes from translucent, part opaque to complete opaque with increasing （temperature.）
文摘Many properties of polyester filaments such as heat shrinkage, tenacity, elongation at break and etc. are greatly influenced by drawing, so post-drawing is important in downstream processing. As more and more profile fibers and multi-variance fibers used in textile industry, the properties of above two kinds of differential polyester filaments after drawing in different heat conditions were studied. Finally following conclusions were obtained: Firstly, the tenacity and elongation at break decreases with the rise of Tp. Secondly, the tenacity rises but the elongation at break decreases with the increase of Tb. Then, when the Tb is low, both the shrinkage in boiling water and hi hot air decreases with the rise of Tp, while, when the Tb is high, both the shrinkage rises with the rise of Tp. The last, both the shrinkage decreases with the rise of Tb.
文摘A general research program, focusing on activated carbon fiber cloths （ACFC） and felt for environmental protection was performed. The objectives were multiple： （i） a better understanding of the adsorption mecha- nisms of these kinds of materials; （ii） the specification and optimization of new processes using these adsorbents; （iii） the modeling of the adsorption of organic pollutants using both the usual and original approaches; （iv） applications of ACFC in industrial processes. The general question was： how can activated carbon fiber cloths and felts be used in air treatment processes for the protection of environment. In order to provide an answer, different approaches were adopted. The materials （ACFC） were characterized in terms of macro structure and internal porosity. Specific studies were performed to get the air flow pattern through the fabrics. Head loss data were generated and modeled as a fi.mction of air velocity. The performances of ACF to remove volatile organic compounds （VOCs） were approached with the adsorption isotherms and breakthrough curves in various operating conditions. Regenera- tion by Joule effect shows a homogenous heating of adsorber modules with rolled or pleated layers. Examples of industrial developments were presented showing an interesting technology for the removal of VOCs, such as dichloromethane, benzene, isopropyl alcohol and toluene, alone or in a complex mixture.
文摘The increase in the population of Tunisia and the industrial development posed with acuity during the end of the major problems. Without contribution of additional resources, water will then be likely to be done increasingly rare. The solar still is a small production system, yielding on average 2-5 L/day. In this study we propose a solar distiller assisted by a heat pump. The design of this distiller uses for the evaporation of water and its condensation two phenomena are studied Simple Solar Distiller （SSD） and Simple Solar Still Distiller Hybrid with heat Pump （SSDHP）. The performance is less than 2 L/mVday and a performance of 30% for the SSD. But the SSDHP is 12 L/m2/day, the energetic efficiency reaches 90%.
