Boronizing was applied to Inconel 718. In order to obtain the optimal combination of strength and ductility, the borided Inconel 718 was subjected to standard heat treatment. This consists of solution treatment and th...Boronizing was applied to Inconel 718. In order to obtain the optimal combination of strength and ductility, the borided Inconel 718 was subjected to standard heat treatment. This consists of solution treatment and then a two-step aging treatment. The borided layer is composed of the compound layer and the boron diffusion zone. Because of the superior hardness of borides, the borided Inconel 718 exhibits a significant reduction in its wear rate and relatively low coefficient of friction （COF） compared with the unborided Inconel 718. The standard heat treatment efficiently promotes the diffusion of boron into the interior of the material and the generation of new borides （Fe2B, CrB）. The borided layer with standard heat treatment shows much better wear resistance due to the thicker borided layer （313.76 μm）.展开更多
The present research is focused on the effects of standard heat treatment on the microstructure and mechanical properties of diffusion brazed IN-738 LC superalloy.Three distinct heat treatment cycles of full solution ...The present research is focused on the effects of standard heat treatment on the microstructure and mechanical properties of diffusion brazed IN-738 LC superalloy.Three distinct heat treatment cycles of full solution annealing,partial solution annealing,and aging treatment were applied to the bonded specimens,sequentially.The results reveal that bonding at 1120℃for 5 min leads to incomplete isothermal solidification and formation of eutectic phases including Ni-and Cr-rich borides in the joint centerline.Increasing the holding time to 45 min leads to the full isothermal solidification and formation of a nickel proeutectic solid-solution phase(γ)in the joints.The standard heat treatment of isothermally solidified and non-isothermally solidified specimens results in the complete elimination of the boride phases in the diffusion-affected zone and also the formation ofγ’precipitates in the isothermally solidified zone.However,discontinuously re-solidified products are observed in joint district in the non-isothermally solidified sample.The highest shear strength(~801 MPa)is achieved for isothermally solidified specimen after standard heat treatment;this strength is approximately 99%that of the substrate material.展开更多
Chip multiprocessors(CMPs) allow thread level parallelism,thus increasing performance.However,this comes with the cost of temperature problem.CMPs require more power,creating non uniform power map and hotspots.Aiming ...Chip multiprocessors(CMPs) allow thread level parallelism,thus increasing performance.However,this comes with the cost of temperature problem.CMPs require more power,creating non uniform power map and hotspots.Aiming at this problem,a thread scheduling algorithm,the greedy scheduling algorithm,was proposed to reduce the thermal emergencies and to improve the throughput.The greedy scheduling algorithm was implemented in the Linux kernel on Intel's Quad-Core system.The experimental results show that the greedy scheduling algorithm can reduce 9.6%-78.5% of the hardware dynamic thermal management(DTM) in various combinations of workloads,and has an average of 5.2% and up to 9.7% throughput higher than the Linux standard scheduler.展开更多
基金Projects(2011CB013402,201303002,2014028002)supported by the National Basic Research Program of China
文摘Boronizing was applied to Inconel 718. In order to obtain the optimal combination of strength and ductility, the borided Inconel 718 was subjected to standard heat treatment. This consists of solution treatment and then a two-step aging treatment. The borided layer is composed of the compound layer and the boron diffusion zone. Because of the superior hardness of borides, the borided Inconel 718 exhibits a significant reduction in its wear rate and relatively low coefficient of friction （COF） compared with the unborided Inconel 718. The standard heat treatment efficiently promotes the diffusion of boron into the interior of the material and the generation of new borides （Fe2B, CrB）. The borided layer with standard heat treatment shows much better wear resistance due to the thicker borided layer （313.76 μm）.
基金support from Ferdowsi University of Mashhad(FUM)under the research scheme(No.2/45210)。
文摘The present research is focused on the effects of standard heat treatment on the microstructure and mechanical properties of diffusion brazed IN-738 LC superalloy.Three distinct heat treatment cycles of full solution annealing,partial solution annealing,and aging treatment were applied to the bonded specimens,sequentially.The results reveal that bonding at 1120℃for 5 min leads to incomplete isothermal solidification and formation of eutectic phases including Ni-and Cr-rich borides in the joint centerline.Increasing the holding time to 45 min leads to the full isothermal solidification and formation of a nickel proeutectic solid-solution phase(γ)in the joints.The standard heat treatment of isothermally solidified and non-isothermally solidified specimens results in the complete elimination of the boride phases in the diffusion-affected zone and also the formation ofγ’precipitates in the isothermally solidified zone.However,discontinuously re-solidified products are observed in joint district in the non-isothermally solidified sample.The highest shear strength(~801 MPa)is achieved for isothermally solidified specimen after standard heat treatment;this strength is approximately 99%that of the substrate material.
基金Projects(2009AA01Z124,2009AA01Z102) supported by the National High Technology Research and Development Program of ChinaProjects(60970036,61076025) supported by the National Natural Science Foundation of China
文摘Chip multiprocessors(CMPs) allow thread level parallelism,thus increasing performance.However,this comes with the cost of temperature problem.CMPs require more power,creating non uniform power map and hotspots.Aiming at this problem,a thread scheduling algorithm,the greedy scheduling algorithm,was proposed to reduce the thermal emergencies and to improve the throughput.The greedy scheduling algorithm was implemented in the Linux kernel on Intel's Quad-Core system.The experimental results show that the greedy scheduling algorithm can reduce 9.6%-78.5% of the hardware dynamic thermal management(DTM) in various combinations of workloads,and has an average of 5.2% and up to 9.7% throughput higher than the Linux standard scheduler.
