Two kinds of unidirectional PAN M40 carbon fiber （55%, volume fraction） reinforced 6061Al and 5A06Al composites were fabricated by the squeeze-casting technology and their interface structure and thermal expansion p...Two kinds of unidirectional PAN M40 carbon fiber （55%, volume fraction） reinforced 6061Al and 5A06Al composites were fabricated by the squeeze-casting technology and their interface structure and thermal expansion properties were investigated. Results showed that the combination between aluminum alloy and fibers was well in two composites and interface reaction in M40/5A06Al composite was weaker than that in M40/6061Al composite. Coefficients of thermal expansion （CTE） of M40/Al composites varied approximately from （1.45-2.68）×10^-6 K^-1 to （0.35-1.44）×10^-6 K^-1 between 20℃ and 450℃, and decreased slowly with the increase of temperature. In addition, the CTE of M40/6061Al composite was lower than that of M40/SA06Al composite. It was observed that fibers were protruded significantly from the matrix after thermal expansion, which demonstrated the existence of interface sliding between fiber and matrix during the thermal expansion. It was believed that weak interracial reaction resulted in a higher CTE. It was found that the experimental CTEs were closer to the predicted values by Schapery model.展开更多
The general steam-injection pressing is mainly used for produce particleboards and medium density fiberboard. However, it is difficult to produce soft fiberboard with desired strength. However, the closing steam-injec...The general steam-injection pressing is mainly used for produce particleboards and medium density fiberboard. However, it is difficult to produce soft fiberboard with desired strength. However, the closing steam-injection pressing that based on the steam-injection pressing could. The wooden frame sealing up the slab could prevent the steam from emitting when the steam injected into the slab. The caloric released by steam condensation make the slab reach high temperature level for a short period. This method is very appropriate for making thick panels in theory, especially for the soft fiberboard. It makes a great leap forward on the hot pressing process that for wood-based panels. Moreover, it will be a meaningful technological breakthrough in developing new products and improving wood utilization.展开更多
基金Project(DL09BB23) supported by the Fundamental Research Funds for the Central Universities in China
文摘Two kinds of unidirectional PAN M40 carbon fiber （55%, volume fraction） reinforced 6061Al and 5A06Al composites were fabricated by the squeeze-casting technology and their interface structure and thermal expansion properties were investigated. Results showed that the combination between aluminum alloy and fibers was well in two composites and interface reaction in M40/5A06Al composite was weaker than that in M40/6061Al composite. Coefficients of thermal expansion （CTE） of M40/Al composites varied approximately from （1.45-2.68）×10^-6 K^-1 to （0.35-1.44）×10^-6 K^-1 between 20℃ and 450℃, and decreased slowly with the increase of temperature. In addition, the CTE of M40/6061Al composite was lower than that of M40/SA06Al composite. It was observed that fibers were protruded significantly from the matrix after thermal expansion, which demonstrated the existence of interface sliding between fiber and matrix during the thermal expansion. It was believed that weak interracial reaction resulted in a higher CTE. It was found that the experimental CTEs were closer to the predicted values by Schapery model.
基金special research of nonprofit industry "Reseach on the Energy-saving and Sound Insulation Wall of PrefabricatedWooden Frame and Structural Materials"(No.200704013)
文摘The general steam-injection pressing is mainly used for produce particleboards and medium density fiberboard. However, it is difficult to produce soft fiberboard with desired strength. However, the closing steam-injection pressing that based on the steam-injection pressing could. The wooden frame sealing up the slab could prevent the steam from emitting when the steam injected into the slab. The caloric released by steam condensation make the slab reach high temperature level for a short period. This method is very appropriate for making thick panels in theory, especially for the soft fiberboard. It makes a great leap forward on the hot pressing process that for wood-based panels. Moreover, it will be a meaningful technological breakthrough in developing new products and improving wood utilization.
