An innovative flat heat pipe radiator was put forward, and it has the features of high efficiency of heat dissipation, compact construction, low thermal resistance, light weight, low cost, and anti-dust-deposition. Th...An innovative flat heat pipe radiator was put forward, and it has the features of high efficiency of heat dissipation, compact construction, low thermal resistance, light weight, low cost, and anti-dust-deposition. The thermal analysis of the flat heat pipe radiator for cooling high-power light emitting diode （LED） array was conducted. The thermal characteristics of the flat heat pipe radiator under the different heat loads and incline angles were investigated experimentally in natural convection. An electro-thermal conversion method was used to measure the junction temperature of the LED chips. It is found that the integral temperature distribution of the flat heat pipe radiator is reasonable and uniform. The total thermal resistance of the flat heat pipe radiator varies in the range of 0.38-0.45 K/W. The junction temperatures of LED chips with the flat heat pipe radiator and with the aluminum board at the same forward current of 0.35 A are 52.5 and 75.2 ℃, respectively.展开更多
This paper presents an experimental study on a flat plate closed loop pulsating heat pipes. It consisted of total 40 channels with square cross section （2 × 2 mm^2, 165 mm long） machined directly on an aluminum...This paper presents an experimental study on a flat plate closed loop pulsating heat pipes. It consisted of total 40 channels with square cross section （2 × 2 mm^2, 165 mm long） machined directly on an aluminum plate（180×120×3 nm^2）, which was covered by a transparent plate. The working fluid employed was ethanol. As the results, the influence parameters of thermal performance were investigated, such as filling ratio, heat load and operational orientations etc. Filling ratio was found to be a critical parameter, and its effect was rather complicated. According to its values the PHP plate could have four distinct working zones with different operational characteristics and heat transfer performance. The effect of heat load on thermal performance was found to be positive, and in general, iucrcasing the heat load would improve heat transfer performance. In order to analyze the effect of gravity on thermal performance, three different heat modes and total seven tilt angles were tested and compared. Successful operation at all orientations with respect to gravity was also achieved.展开更多
A stress analysis is described for a nuclear steam generator tubesheet with a thin, or irregular ligament, associated with a mis-drilled hole using the rules of ASME （American Society of Mechanical Engineers） B ＆ P...A stress analysis is described for a nuclear steam generator tubesheet with a thin, or irregular ligament, associated with a mis-drilled hole using the rules of ASME （American Society of Mechanical Engineers） B ＆ PV Section Ⅲ and non-mandatory Appendix A, Article A-8000 for stresses in perforated flat plates. The analysis demonstrates the proper application of the NB-3200 rules for this special application, with discussion of the differences between an actual tube hole deviation and what is assumed in ASME Appendix A. This is a companion paper to ＂Technical Justification Supporting Operation with a Tube Installed in a Mis-Drilled Hole of a Steam Generator Tubesheet＂.展开更多
Temperature distribution over the absorber plate of a parallel flow flat-plate solar collector is numerically analyzed. The governing differential equations with boundary conditions are solved numerically using fluent...Temperature distribution over the absorber plate of a parallel flow flat-plate solar collector is numerically analyzed. The governing differential equations with boundary conditions are solved numerically using fluent software. Effects of the inlet mass flux, inlet temperature and tube spacing on velocity and temperature distributions are discussed. Numerical results show that the distributions of velocity and temperature of fluid is unsymmetrical inside pipe.展开更多
Flat plate pulsating heat pipe is useful for hot spot heat spreader. Two kinds of flat plate spreader of pulsating heat pipe are designed, fabricated and experimented. For the embedded circular capillary type, the tra...Flat plate pulsating heat pipe is useful for hot spot heat spreader. Two kinds of flat plate spreader of pulsating heat pipe are designed, fabricated and experimented. For the embedded circular capillary type, the transferred heat flux could reach 32 W/cm2, the smallest thermal resistance for acetone, methanol and FC-72 were respectively 0.50, 0.57 and 0.40℃/W. While for the square capillary type, the transferred heat flux could reach 26 W/cm2, the equivalent thermal conductivity could reach 3211 W/（m. ℃）. There are ranges of optimal transferred power and filling ratio for different working liquid. If the transferred power is constant, changing the heating area and the place has little effects on the performance.展开更多
This paper introduces a novel fiat plate solar collector （FPC） using micro heat pipe array （MHPA） as a key element. To analyze the thermal transfer behavior of flat plate solar collector with micro heat pipe array...This paper introduces a novel fiat plate solar collector （FPC） using micro heat pipe array （MHPA） as a key element. To analyze the thermal transfer behavior of flat plate solar collector with micro heat pipe array （MHPA-FPC）, an indoor experiment for thermal transfer characteristic of MHPA applied to FPC was conducted by using an electrical heating film to simulate the solar radiation. Different cooling water flow rates, cooling water temperatures, slopes, and contact thermal resistances be- tween the condenser of MHPA and the heat exchanger were tested at different heating powers. The experimental results in- dicate that MHPA-FPC exhibits the enhanced heat transfer capability with increased cooling water flow rate and temperature. Total thermal resistance has a maximum decline of approximately 10% when the flow rate increases from 180 to 360 L h-1 and 38% when the cooling water temperature increases from 20~C to 40~C. When the inclination angle of MHPA-FPC ex- ceeds 30~, the slope change has a negligible effect on the heat transfer performance of MHPA-FPC. In addition, contact thermal resistance significantly affects the heat transfer capability of MHPA-FPC. The total thermal resistances lowers to nearly half of the original level when contact material between the condenser of MHPA and the heat exchanger changes from conductive silicone to conductive grease. These results could provide useful information for the optimal design and operation of MHPA-FPC.展开更多
There has been a strong interest in the use of Phase Change Materials (PCMs) for the transient thermal abatement of high powered microprocessor.This paper presents a set of transient computational analysis for selecte...There has been a strong interest in the use of Phase Change Materials (PCMs) for the transient thermal abatement of high powered microprocessor.This paper presents a set of transient computational analysis for selected IC packages with the purpose of calibrating the merits of PCM in different configurations.The transient analysis of high powered microprocessors with heat sinks was performed as a benchmark for comparison with the same microprocessors fitted with PCM in the following configurations:a) PCM imbedded into the finned region of the heat sink,b) PCM mounted between the microprocessor and heat sink,c) sealed PCM underfill to the microprocessor and d) PCM fitted to the underside of the printed circuit board directly beneath the microprocessor.The analysis was performed using a commercial CFD tool together with an approximation to the phase change mechanism using the slope method.Results indicate the merit of each configuration.展开更多
An experimental system of flat plate pulsating heat pipe was established and experimental research was carried out in this system to know the mechanism of heat transfer, start-up and operating characteristics. The fac...An experimental system of flat plate pulsating heat pipe was established and experimental research was carried out in this system to know the mechanism of heat transfer, start-up and operating characteristics. The factors, such as filling rate, heating power, heating method etc, which have great influence on the thermal performance of the plate pulsating heat pipe were discussed. The results indicate that heating power and filling rate are the important factors for the start-up of the plate pulsating heat pipe. The different start-up power is needed with different filling rate, and the start-up of the heat pipe in case of bottom heated is much easier than that of top heated. Increasing the heating power and enlarging the heating area can make the start-up easier. Heating power can also affect the start-up time of heat pipe under the condition of bottom heated, while it does not have some influence to the heat pipe of top heated. The thermal resistance of plate pulsating heat pipe is related with the heating power, and the higher the heating power is, the smaller the thermal resistance is. But the best filling rate which the heat pipe needs is different with different heating methods, and the performance of the heat pipe in the case of bottom heated is better than the others.展开更多
基金Project(50876016) support by the National Natural Science Foundation of China
文摘An innovative flat heat pipe radiator was put forward, and it has the features of high efficiency of heat dissipation, compact construction, low thermal resistance, light weight, low cost, and anti-dust-deposition. The thermal analysis of the flat heat pipe radiator for cooling high-power light emitting diode （LED） array was conducted. The thermal characteristics of the flat heat pipe radiator under the different heat loads and incline angles were investigated experimentally in natural convection. An electro-thermal conversion method was used to measure the junction temperature of the LED chips. It is found that the integral temperature distribution of the flat heat pipe radiator is reasonable and uniform. The total thermal resistance of the flat heat pipe radiator varies in the range of 0.38-0.45 K/W. The junction temperatures of LED chips with the flat heat pipe radiator and with the aluminum board at the same forward current of 0.35 A are 52.5 and 75.2 ℃, respectively.
基金Supported by the Ger man National Science Foundation (DFG)(No. GR412/33)
文摘This paper presents an experimental study on a flat plate closed loop pulsating heat pipes. It consisted of total 40 channels with square cross section （2 × 2 mm^2, 165 mm long） machined directly on an aluminum plate（180×120×3 nm^2）, which was covered by a transparent plate. The working fluid employed was ethanol. As the results, the influence parameters of thermal performance were investigated, such as filling ratio, heat load and operational orientations etc. Filling ratio was found to be a critical parameter, and its effect was rather complicated. According to its values the PHP plate could have four distinct working zones with different operational characteristics and heat transfer performance. The effect of heat load on thermal performance was found to be positive, and in general, iucrcasing the heat load would improve heat transfer performance. In order to analyze the effect of gravity on thermal performance, three different heat modes and total seven tilt angles were tested and compared. Successful operation at all orientations with respect to gravity was also achieved.
文摘A stress analysis is described for a nuclear steam generator tubesheet with a thin, or irregular ligament, associated with a mis-drilled hole using the rules of ASME （American Society of Mechanical Engineers） B ＆ PV Section Ⅲ and non-mandatory Appendix A, Article A-8000 for stresses in perforated flat plates. The analysis demonstrates the proper application of the NB-3200 rules for this special application, with discussion of the differences between an actual tube hole deviation and what is assumed in ASME Appendix A. This is a companion paper to ＂Technical Justification Supporting Operation with a Tube Installed in a Mis-Drilled Hole of a Steam Generator Tubesheet＂.
文摘Temperature distribution over the absorber plate of a parallel flow flat-plate solar collector is numerically analyzed. The governing differential equations with boundary conditions are solved numerically using fluent software. Effects of the inlet mass flux, inlet temperature and tube spacing on velocity and temperature distributions are discussed. Numerical results show that the distributions of velocity and temperature of fluid is unsymmetrical inside pipe.
文摘Flat plate pulsating heat pipe is useful for hot spot heat spreader. Two kinds of flat plate spreader of pulsating heat pipe are designed, fabricated and experimented. For the embedded circular capillary type, the transferred heat flux could reach 32 W/cm2, the smallest thermal resistance for acetone, methanol and FC-72 were respectively 0.50, 0.57 and 0.40℃/W. While for the square capillary type, the transferred heat flux could reach 26 W/cm2, the equivalent thermal conductivity could reach 3211 W/（m. ℃）. There are ranges of optimal transferred power and filling ratio for different working liquid. If the transferred power is constant, changing the heating area and the place has little effects on the performance.
基金financially supported by the Natural Science Foundation of Beijing(Grant No.Z1004020201201)the Opening Funds of State Key Laboratory of Building Safety and Build Environment of China(Grant No.BSBE 2011-07)
文摘This paper introduces a novel fiat plate solar collector （FPC） using micro heat pipe array （MHPA） as a key element. To analyze the thermal transfer behavior of flat plate solar collector with micro heat pipe array （MHPA-FPC）, an indoor experiment for thermal transfer characteristic of MHPA applied to FPC was conducted by using an electrical heating film to simulate the solar radiation. Different cooling water flow rates, cooling water temperatures, slopes, and contact thermal resistances be- tween the condenser of MHPA and the heat exchanger were tested at different heating powers. The experimental results in- dicate that MHPA-FPC exhibits the enhanced heat transfer capability with increased cooling water flow rate and temperature. Total thermal resistance has a maximum decline of approximately 10% when the flow rate increases from 180 to 360 L h-1 and 38% when the cooling water temperature increases from 20~C to 40~C. When the inclination angle of MHPA-FPC ex- ceeds 30~, the slope change has a negligible effect on the heat transfer performance of MHPA-FPC. In addition, contact thermal resistance significantly affects the heat transfer capability of MHPA-FPC. The total thermal resistances lowers to nearly half of the original level when contact material between the condenser of MHPA and the heat exchanger changes from conductive silicone to conductive grease. These results could provide useful information for the optimal design and operation of MHPA-FPC.
文摘There has been a strong interest in the use of Phase Change Materials (PCMs) for the transient thermal abatement of high powered microprocessor.This paper presents a set of transient computational analysis for selected IC packages with the purpose of calibrating the merits of PCM in different configurations.The transient analysis of high powered microprocessors with heat sinks was performed as a benchmark for comparison with the same microprocessors fitted with PCM in the following configurations:a) PCM imbedded into the finned region of the heat sink,b) PCM mounted between the microprocessor and heat sink,c) sealed PCM underfill to the microprocessor and d) PCM fitted to the underside of the printed circuit board directly beneath the microprocessor.The analysis was performed using a commercial CFD tool together with an approximation to the phase change mechanism using the slope method.Results indicate the merit of each configuration.
基金support of this work by the National Natural Science Foundation of China (No.50776006)
文摘An experimental system of flat plate pulsating heat pipe was established and experimental research was carried out in this system to know the mechanism of heat transfer, start-up and operating characteristics. The factors, such as filling rate, heating power, heating method etc, which have great influence on the thermal performance of the plate pulsating heat pipe were discussed. The results indicate that heating power and filling rate are the important factors for the start-up of the plate pulsating heat pipe. The different start-up power is needed with different filling rate, and the start-up of the heat pipe in case of bottom heated is much easier than that of top heated. Increasing the heating power and enlarging the heating area can make the start-up easier. Heating power can also affect the start-up time of heat pipe under the condition of bottom heated, while it does not have some influence to the heat pipe of top heated. The thermal resistance of plate pulsating heat pipe is related with the heating power, and the higher the heating power is, the smaller the thermal resistance is. But the best filling rate which the heat pipe needs is different with different heating methods, and the performance of the heat pipe in the case of bottom heated is better than the others.
