Fe-Mn-Si系形状记忆合金中热诱发ε_M的单元结构及生长特性研究

用透射电子显微镜观察了Fe-17M-10Cr-5Si-4Ni合金中热诱发ε马氏体(εM)的组成结构,探讨了εM生长特性,实验表明,合金中较大尺寸的热诱发εM具有由生长取向大致相同的单元以首尾相接方式组成的结构特点,层错带平行分布的体系中εM具有促发形核、接续长大的生长特性。

Thermodynamics and characterization of shape memory Cu-Al-Zn alloys

The thermodynamic properties and the microstructure, hardness and electrical conductivity of shape memory alloys （SMAs） belonging to ternary Cu？Al？Zn system were studied by Muggianu model and experiment, respectively. The isothermal section of phase diagram at 293 K was calculated using Thermo-Calc software. Experiments were conducted by X-ray diffraction, light optic microscopy, scanning electron microscopy with energy dispersive X-ray spectrometry, hardness and electrical conductivity measurements. The calculated values of thermodynamic properties indicate that Cu shows good miscibility with Al and Zn in all investigated alloys. The microstructural analysis of samples reveals that the structure consists of large and polygonal grains.

Constitutive equation and processing map of equiatomic NiTi shape memory alloy under hot plastic deformation

In order to describe the deformation behavior and the hot workability of equiatomic NiTi shape memory alloy (SMA) during hot deformation, Arrhenius-type constitutive equation and hot processing map of the alloy were developed by hot compression tests at temperatures ranging from 500 to 1100 °C and strain rates ranging from 0.0005 to 0.5 s?1. The results show that the instability region of the hot processing map increases with the increase of deformation extent. The instability occurs in the low and high temperature regions. The instability region presents the adiabatic shear bands at low temperatures, but it exhibits the abnormal growth of the grains at high temperatures. Consequently, it is necessary to avoid processing the equiatomic NiTi SMA in these regions. It is preferable to process the NiTi SMA at the temperatures ranging from 750 to 900 °C.

Constitutive behavior of Ni-Ti shape memory alloy under hot compression

Constitutive behavior of nickel-titanium shape memory alloy （Ni-Ti SMA） under hot deformation was investigated by means of the compression tests and the linear fitting method. Based on the true stres-strain curves of Ni-Ti SMA under compression at the strain rates of 0.001-1 s land at the temperatures ranging from 600 to 1 000 ℃, the constitutive equation of Ni-Ti SMA with respect to the Zener-Hollomon parameter was established according to the high stress level and the low stress level at various temperatures so as to more accurately describe the deformation behavior of Ni-Ti SMA during hot working. Dynamic recovery and dynamic recrystallization of Ni-Ti SMA occur under hot compression, which lays the theoretical foundation for understanding the constitutive behavior of Ni-Ti SMA.

Superelastic properties of nanocrystalline NiTi shape memory alloy produced by thermomechanical processing

Effects of thermomechanical treatment of cold rolling followed by annealing on microstructure and superelastic behavior of the Ni50Ti50 shape memory alloy were studied.Several specimens were produced by copper boat vacuum induction melting.The homogenized specimens were hot rolled and annealed at 900°C.Thereafter,annealed specimens were subjected to cold rolling with different thickness reductions up to 70%.Transmission electron microscopy revealed that the severe cold rolling led to the formation of a mixed microstructure consisting of nanocrystalline and amorphous phases in Ni50Ti50 alloy.After annealing at 400°C for 1 h,the amorphous phase formed in the cold-rolled specimens was crystallized and a nanocrystalline structure formed.Results showed that with increasing thickness reduction during cold rolling,the recoverable strain of Ni50Ti50 alloy was increased during superelastic experiments such that the 70%cold rolled-annealed specimen exhibited about 12%of recoverable strain.Moreover,with increasing thickness reduction,the critical stress for stress-induced martensitic transformation was increased.It is noteworthy that in the 70%cold rolled-annealed specimen,the damping capacity was measured to be 28 J/cm3 that is significantly higher than that of commercial NiTi alloys.

Thermo-mechanical Behaviors of Functionally Graded Shape Memory Alloy Timoshenko Composite Beams

This paper focuses on the thermo-mechanical behaviors of functionally graded(FG)shape memory alloy(SMA)composite beams based on Timoshenko beam theory.The volume fraction of SMA fiber is graded in the thickness of beam according to a power-law function and the equivalent parameters are formulated.The governing differential equations,which can be solved by direct integration,are established by employing the composite laminated plate theory.The influences of FG parameter,ambient temperature and SMA fiber laying angle on the thermo-mechanical behaviors are numerically simulated and discussed under different boundary conditions.Results indicate that the neutral plane does not coincide with the middle plane of the composite beam and the distribution of martensite is asymmetric along the thickness.Both the increments of the functionally graded parameter and ambient temperature make the composite beam become stiffer.However,the influence of the SMA fiber laying angle can be negligent.This work can provide the theoretical basis for the design and application of FG SMA structures.

A free-cutting and ductile CuAlMnZnTiB shape memory alloy

The mechanical properties and cutting performance of the designed Cu Al Mn Zn Ti B shape memory alloy were studied by tensile test and microstructure observation. Using X-ray diffractometry, differential scanning calorimetry(DSC) and semi-quantitative shape memory effect test, the microstructure and shape memory effect were analyzed. It is found that lots of βphase and few α phase are formed in the quenching of Cu-7.5Al-9.7Mn-3.4Zn-0.3Ti-0.14B(mass fraction, %) alloy, a great deal of martensite and few α phase are formed in the aging alloy, while the annealing alloy is composed of a great deal of α phase and few βphase. The tensile strength and elongation of the annealed alloy are 649 MPa and 17.1%, respectively. Some tiny and dispersion distributed second phase particles are generated in Ti and B precipitates, greatly improving the alloy machinability.

Mechanocaloric materials for solid-state cooling

This article reviews the up-to-date progress in mechanocaloric effect and materials near ambient temperature. For elastocaloric materials, we focus on directly measured temperature change and its entropy origin in nonmagnetic and magnetic shape memory alloys. In terms of barocaloric materials, change in magnetic state, volume and shift of transition temperature due to hydrostatic pressure are systematically compared. We propose advantages and challenges of elastocaloric materials for solidstate cooling. Strategies to enhance elastocaloric and mechanical stability under long-term mechanical cycles are presented. Finally, we conclude with an outlook on the prospect of elastocaloric cooling application.