A three-dimensional finite element approach based on ABAQUS code was developed to investigate the effect of welding sequence on welding residual stress distribution in a thin-walled 6061 aluminum alloy structure. To o...A three-dimensional finite element approach based on ABAQUS code was developed to investigate the effect of welding sequence on welding residual stress distribution in a thin-walled 6061 aluminum alloy structure. To obtain sound numerical results, the therrno-mechanical behaviour was simulated using a direct-coupled formulation. Nine different simulation sequences were carried out by single-pass TIG welding of an octagonal pipe-plate joint, and the distributions of longitudinal and transverse residual stresses both on the outer and inner surfaces of the pipe were analyzed. The results suggest that the final residual stresses in the weld and its vicinity are not affected by the initial residual stresses of the structure. Selecting a suitable welding sequence can reduce the final residual stress in an octagonal pipe-plate joint.展开更多
As a result of the lower backing weld efficiency, the applying of automatic welding is seriously limited. So a kind of special automatic welder is designed and manufactured for backing weld. This paper introduces the ...As a result of the lower backing weld efficiency, the applying of automatic welding is seriously limited. So a kind of special automatic welder is designed and manufactured for backing weld. This paper introduces the character of the assembled pulse CO2 arc welding machine which has strong penetrability. It specifies the technology of controlling the parameters of all position automatic welding by computer and multi-axis controller. Moreover typical welding procedure parameters are provided. It is proved by examination that the economical and practical equipment and technology are suitable for the long-distance transmission pipeline, and it has a good foreground of spreading and applying.展开更多
The mechanical characteristics of the weld joint were investigated by tensile test, microstructure test, and microhardness test. The welded tube NC bending tests were carried out to evaluate the weld on the formabilit...The mechanical characteristics of the weld joint were investigated by tensile test, microstructure test, and microhardness test. The welded tube NC bending tests were carried out to evaluate the weld on the formability of the QSTE340 welded tube. The results show that the wall thinning degree, cross-sectional deformation and springback angle increase significantly as the weld line is located on the outside of the bend compared with that located on the middle and inside, and the welded tubes produce nearly identical performance as the weld line is located on the middle and inside. The wall thickening degree decreases much as the weld line is located on the inside of the bend. So the welded tube can acquire good bending formability as the weld line is located in the region away from the outside of the bend.展开更多
Polyethylene material has some specification that makes very difficult any kind of inspection based on ultrasonic. The acoustic impedance and sound velocity in this kind of material are near to the materials commonly ...Polyethylene material has some specification that makes very difficult any kind of inspection based on ultrasonic. The acoustic impedance and sound velocity in this kind of material are near to the materials commonly used in ultrasonic wedges. Also this kind of materials are highly attenuative materials for ultrasound. To inspection of polyethylene circumferential but welds and overcome to all the problems mentioned, the especial technique of TOFD （Time of Flight Diffraction） method which employs low frequency probe and concentrate on the inspection area that longitudinal waves turn into transverse waves has been used. The purpose of inspection is determining the exact location of surface and internal welding defects. For this purpose, two separate polyethylene pipes with 10 inch in diameter, 15 mm thickness and also 25 inch diameter, 28 mm thickness, were selected. In total 40 artificial defects which involve 28 side drill holes in deferent depths and 12 surface and sub-surface notches were created. All artificially created defects were detected with very good accuracy. Unlike the conventional TOFD method which have 2 to 3 mm dead zone, by using the above method even surface notch with 0.5 mm has been detected.展开更多
基金Project(61075005)supported by the Fund of State Key Laboratory of Advanced Design and Manufacture for Vehicle Body in Hunan University,ChinaProject(09JJ1007)supported by Preeminent Youth Fund of Hunan Province,ChinaProject(51075132)supported by the National Natural Science Foundation of China
文摘A three-dimensional finite element approach based on ABAQUS code was developed to investigate the effect of welding sequence on welding residual stress distribution in a thin-walled 6061 aluminum alloy structure. To obtain sound numerical results, the therrno-mechanical behaviour was simulated using a direct-coupled formulation. Nine different simulation sequences were carried out by single-pass TIG welding of an octagonal pipe-plate joint, and the distributions of longitudinal and transverse residual stresses both on the outer and inner surfaces of the pipe were analyzed. The results suggest that the final residual stresses in the weld and its vicinity are not affected by the initial residual stresses of the structure. Selecting a suitable welding sequence can reduce the final residual stress in an octagonal pipe-plate joint.
文摘As a result of the lower backing weld efficiency, the applying of automatic welding is seriously limited. So a kind of special automatic welder is designed and manufactured for backing weld. This paper introduces the character of the assembled pulse CO2 arc welding machine which has strong penetrability. It specifies the technology of controlling the parameters of all position automatic welding by computer and multi-axis controller. Moreover typical welding procedure parameters are provided. It is proved by examination that the economical and practical equipment and technology are suitable for the long-distance transmission pipeline, and it has a good foreground of spreading and applying.
基金Supported by National Natural Science Foundation of China (No. 50875216)
文摘The mechanical characteristics of the weld joint were investigated by tensile test, microstructure test, and microhardness test. The welded tube NC bending tests were carried out to evaluate the weld on the formability of the QSTE340 welded tube. The results show that the wall thinning degree, cross-sectional deformation and springback angle increase significantly as the weld line is located on the outside of the bend compared with that located on the middle and inside, and the welded tubes produce nearly identical performance as the weld line is located on the middle and inside. The wall thickening degree decreases much as the weld line is located on the inside of the bend. So the welded tube can acquire good bending formability as the weld line is located in the region away from the outside of the bend.
文摘Polyethylene material has some specification that makes very difficult any kind of inspection based on ultrasonic. The acoustic impedance and sound velocity in this kind of material are near to the materials commonly used in ultrasonic wedges. Also this kind of materials are highly attenuative materials for ultrasound. To inspection of polyethylene circumferential but welds and overcome to all the problems mentioned, the especial technique of TOFD （Time of Flight Diffraction） method which employs low frequency probe and concentrate on the inspection area that longitudinal waves turn into transverse waves has been used. The purpose of inspection is determining the exact location of surface and internal welding defects. For this purpose, two separate polyethylene pipes with 10 inch in diameter, 15 mm thickness and also 25 inch diameter, 28 mm thickness, were selected. In total 40 artificial defects which involve 28 side drill holes in deferent depths and 12 surface and sub-surface notches were created. All artificially created defects were detected with very good accuracy. Unlike the conventional TOFD method which have 2 to 3 mm dead zone, by using the above method even surface notch with 0.5 mm has been detected.
