In this study, we established a rapid acid digestion for determining Hf-Sr-Nd isotopic ratios of geological samples by using MC-ICP-MS. Conditions of 1600 ℃ for 1 min and 1400 ℃ for 1 min were adopted for fusing int...In this study, we established a rapid acid digestion for determining Hf-Sr-Nd isotopic ratios of geological samples by using MC-ICP-MS. Conditions of 1600 ℃ for 1 min and 1400 ℃ for 1 min were adopted for fusing intrusive rocks and extrusive rocks, respectively. The rapid acid digestion technique is superior in digestion time compared with high-pressure PTFE bomb method. The procedural blanks of the method were also lower than that flux fusion. Replicate analyses of international certified reference materials （CRMs） indicate that isotopic ratios of ^176Hf/^177Hf, ^87Sr/^86Sr and 143Nd/144Nd agree well with previously published data. The external reproducibility （2SD, n = 5） of ten CRMs are ±0.000030 for ^87Sr/^86Sr, ± 0.000030 for ^143Nd/^144Nd, and ±0.000018 for ^176Hf/^177Hf.展开更多
Our civilization is facing an urgent need to include innovative, large-scale sources of energy and raw materials into its technological cycles. One potential source is magma, which now still inspires awe with its unpr...Our civilization is facing an urgent need to include innovative, large-scale sources of energy and raw materials into its technological cycles. One potential source is magma, which now still inspires awe with its unpredictable power of volcanic eruptions. We propose a method of remote control of lava flow which is based on a special design of a pipe which is lowered into the crater of a volcano. The magma is raised with the help of a well-known method for raising liquids, the airlift. This article includes a detailed description of the structure of the disperser that we shall use to introduce gas into the magma, explains the possible ways to manage the flow of magma, and describes the results that can be achieved. There is potential for the establishment of a whole new industry that will produce cheap electricity, hydrogen, rare metals, fertilizers and innovative construction materials.展开更多
The present study reports investigations on rheological,mechanical,thermal,tribological and morphological properties of feedstock filaments prepared with polylactic acid-polyether ketone ketone-hydroxyapatite-chitosan...The present study reports investigations on rheological,mechanical,thermal,tribological and morphological properties of feedstock filaments prepared with polylactic acid-polyether ketone ketone-hydroxyapatite-chitosan(PLA-PEKK-HAp-CS)composite for 3D printing of functional prototypes.The study consists of a series of melt processing operations on melt flow index(MFI)setup as per ASTM D-1238 for melt flow certainty followed by fixation of reinforcement composition/proportion as 94%PEKK-4%HAp-2%CS(B)by mass in PLA matrix(A).The blending of reinforcement and preparation of feedstock filament for fused deposition modeling(FDM)set up has been performed on commercial twin screw extruder(TSE).The results of study suggest that feedstock filaments prepared with blend of 95%A-5%B(by mass)at 200℃processing temperature and 100 r/min rotational speed on TSE resulted into better tensile properties(35.9 MPa peak strength and 32.3 MPa break strength)with 6.24%surface porosity,42.67 nm surface roughness(R_(a))and acceptable heat capacity(2.14 J/g).However as regards to tribological behavior,the minimum wear of 316μm was observed for sample with poor tensile properties.As regards to crash application for scaffolds the maximum toughness of 1.16 MPa was observed for 85%A-15%B(by mass)at 200℃processing temperature and 150 r/min rotational speed on TSE.展开更多
基金supported by the National Natural Science Foundation of China (Grant Nos. 41421002, 41427804, and 41373004)the MOST Research Foundation from the State Key Laboratory of Continental Dynamics (Grant Nos. BJ08132-1, 207010021, and 201210004)
文摘In this study, we established a rapid acid digestion for determining Hf-Sr-Nd isotopic ratios of geological samples by using MC-ICP-MS. Conditions of 1600 ℃ for 1 min and 1400 ℃ for 1 min were adopted for fusing intrusive rocks and extrusive rocks, respectively. The rapid acid digestion technique is superior in digestion time compared with high-pressure PTFE bomb method. The procedural blanks of the method were also lower than that flux fusion. Replicate analyses of international certified reference materials （CRMs） indicate that isotopic ratios of ^176Hf/^177Hf, ^87Sr/^86Sr and 143Nd/144Nd agree well with previously published data. The external reproducibility （2SD, n = 5） of ten CRMs are ±0.000030 for ^87Sr/^86Sr, ± 0.000030 for ^143Nd/^144Nd, and ±0.000018 for ^176Hf/^177Hf.
文摘Our civilization is facing an urgent need to include innovative, large-scale sources of energy and raw materials into its technological cycles. One potential source is magma, which now still inspires awe with its unpredictable power of volcanic eruptions. We propose a method of remote control of lava flow which is based on a special design of a pipe which is lowered into the crater of a volcano. The magma is raised with the help of a well-known method for raising liquids, the airlift. This article includes a detailed description of the structure of the disperser that we shall use to introduce gas into the magma, explains the possible ways to manage the flow of magma, and describes the results that can be achieved. There is potential for the establishment of a whole new industry that will produce cheap electricity, hydrogen, rare metals, fertilizers and innovative construction materials.
基金Guru Nanak at Dev Engg. College, Ludhiana (GNDEC) and SERB (File No. IMRC/AISTDF/R&D/P-10/2017) for providing financial/technical assistance to carry out the research
文摘The present study reports investigations on rheological,mechanical,thermal,tribological and morphological properties of feedstock filaments prepared with polylactic acid-polyether ketone ketone-hydroxyapatite-chitosan(PLA-PEKK-HAp-CS)composite for 3D printing of functional prototypes.The study consists of a series of melt processing operations on melt flow index(MFI)setup as per ASTM D-1238 for melt flow certainty followed by fixation of reinforcement composition/proportion as 94%PEKK-4%HAp-2%CS(B)by mass in PLA matrix(A).The blending of reinforcement and preparation of feedstock filament for fused deposition modeling(FDM)set up has been performed on commercial twin screw extruder(TSE).The results of study suggest that feedstock filaments prepared with blend of 95%A-5%B(by mass)at 200℃processing temperature and 100 r/min rotational speed on TSE resulted into better tensile properties(35.9 MPa peak strength and 32.3 MPa break strength)with 6.24%surface porosity,42.67 nm surface roughness(R_(a))and acceptable heat capacity(2.14 J/g).However as regards to tribological behavior,the minimum wear of 316μm was observed for sample with poor tensile properties.As regards to crash application for scaffolds the maximum toughness of 1.16 MPa was observed for 85%A-15%B(by mass)at 200℃processing temperature and 150 r/min rotational speed on TSE.
