Two additives of ethylene diamine tetraacetic acid （EDTA） and ammonium chloride （NH4C1） were separately used in the electrodeposition of Zn-Ni alloy films from a deep eutectic solvent. The effects of these two add...Two additives of ethylene diamine tetraacetic acid （EDTA） and ammonium chloride （NH4C1） were separately used in the electrodeposition of Zn-Ni alloy films from a deep eutectic solvent. The effects of these two additives on electrodeposition behavior, composition, morphology, and corrosion performance of the Zn-Ni alloys were investigated. The electrodeposition behaviors of Zn-Ni alloy revealed by the cyclic voltammetry show that the addition of EDTA to the Zn-Ni electrolyte enhances the Zn incorporation into the alloy film while the addition of NH4C1 produces an opposite effect by suppressing Zn incorporation into the film. With an increase of EDTA concentration in the electrolyte, the Zn content of the Zn-Ni films increases, while the grain size of the deposits and the current efficiency of the plating process decrease. The increase of NH4C1 concentration in the electrolyte would significantly refine the grain size of the electrodeposited Zn-Ni films, reduce the Zn content and increase the cathodic current efficiency. The corrosion testing indicates that the barrier corrosion resistances of Zn-Ni films electrodeposited from NHnC1 containing electrolytes are superior to those electrodeposited from EDTA-containing electrolytes, which in turn are superior to those electrodeposited from additive-free electrolytes.展开更多
To improve the wear and corrosion properties of AZ91D magnesium alloys,Cu-based amorphous composite coatings were fabricated on AZ91D magnesium alloy by laser cladding using mixed powders of Cu47Ti34Zr11Ni8 and SiC.Th...To improve the wear and corrosion properties of AZ91D magnesium alloys,Cu-based amorphous composite coatings were fabricated on AZ91D magnesium alloy by laser cladding using mixed powders of Cu47Ti34Zr11Ni8 and SiC.The wear and corrosion behaviours of the coatings were investigated.The wear resistance of the coatings was evaluated under dry sliding wear condition at room temperature.The corrosion resistance of the coatings was tested in 3.5%(mass fraction) NaCl solution.The coatings exhibit excellent wear resistance due to the recombined action of amorphous phase and different intermetallic compounds.The main wear mechanisms of the coatings and the AZ91D sample are different.The former is abrasive wear and the latter is adhesive wear.The coatings compared with AZ91D magnesium alloy also exhibit good corrosion resistance because of the presence of the amorphous phase in the coatings.展开更多
The microstructure evolution, mechanical and corrosion properties of Al-11Si-2Cu-0.8Zn die cast alloy treated with Bi, Sb and Sr additions were investigated. The results of mechanical testing showed that all additions...The microstructure evolution, mechanical and corrosion properties of Al-11Si-2Cu-0.8Zn die cast alloy treated with Bi, Sb and Sr additions were investigated. The results of mechanical testing showed that all additions increased impact toughness, ultimate tensile strength, and elongation of the alloy as a result of change in eutectic Si morphology. The analysis of fracture surfaces revealed that with addition of Sr and to lesser extent Bi and Sb, the alloy exhibited a predominantly ductile fracture rather than quasi-cleavage brittle fracture. Moreover, with the additions of Sr, Bi and Sb, the quality index increased to 164.7 MPa, 156.3 MPa and 152.6 MPa respectively from 102 MPa for the base alloy. Polarization corrosion tests conducted in sodium chloride solution showed that the corrosion potential shifted to more negative values with additions of Sb, Bi and Sr, respectively. Corrosion immersion tests also revealed that the element additions have a detrimental effect on the corrosion rate of alloys, due to the increase of boundaries between the Al and eutectic Si phases.展开更多
In order to study the corrosion resistance of high-speed laser cladding(HLC) coating while improving production efficiency,a CoCrFeNiMo_(0.2)high-entropy alloy(HEA) coating was prepared by HLC.The optimized parameters...In order to study the corrosion resistance of high-speed laser cladding(HLC) coating while improving production efficiency,a CoCrFeNiMo_(0.2)high-entropy alloy(HEA) coating was prepared by HLC.The optimized parameters of HLC are laser power of 880 W,scanning speed of 18 m/min,overlapping ratio of 60%,and powder feed speed of 3 r/min.Then,the surface roughness,microstructure,phase composition,element distribution,and electrochemical properties in 3.5 wt% NaCl solution of the coatings were analyzed,respectively.The local surface roughness of the CoCrFeNiMo_(0.2)HEA coating was found to be 15.53 μm.A distinct metallurgical bond could be observed between the coating and the substrate.Compared to the conventional laser cladding(CLC),the results of electrochemical tests showed that CoCrFeNiMo_(0.2)HEA coating exhibited a significant passivation.The corrosion current density of 5.4411 × 10^(-6)A·cm^(-2) and the corrosion potential of-0.7445 V for the HLC coating were calculated by the Tafel extrapolation method.The CLC coating’s corrosion current density and corrosion potential are 2.7083×10^(-5)A·cm^(-2) and-0.9685 V,respectively.The HLC coating shows a superior corrosion resistance,crucially due to the uniform and fine grains.Under various complex and harsh working conditions,this method can be widely used in the field of repairing and remanufacturing of corro sion-proof workpiece s.展开更多
Two types of composites were prepared with Al-4.5Cu alloy as a matrix using stir casting method.One was reinforced with 10wt.%of Si C and 2wt.%of MoS2.The other was reinforced with 10wt.%of Si C and 4wt.%of MoS2.Their...Two types of composites were prepared with Al-4.5Cu alloy as a matrix using stir casting method.One was reinforced with 10wt.%of Si C and 2wt.%of MoS2.The other was reinforced with 10wt.%of Si C and 4wt.%of MoS2.Their surfaces were remelted using a CO2 laser beam with an objective to study the influence of laser surface melting(LSM).The topography,microhardness,corrosion resistance and wear resistance of the laser melted surfaces were studied.Overall surface integrity after LSM was compared with as-cast surface.LSM enhanced the microhardness and wear resistance of the surface in each case.Porosity of the laser melted surface was low and corrosion resistance was high.Thus,LSM can be conveniently applied to enhancing the surface integrity of the aluminium composites.However,there is an optimum laser specific energy,around 38 J/m^2 in this study,for obtaining the best surface integrity.展开更多
A comparative study on the corrosion resistance of NiFe_2O_4 ceramic inert anode for aluminum electrolysis prepared in the different sintering atmosphere was carried out in Na_3AlF_6-Al_2O_3 melt.The results show that...A comparative study on the corrosion resistance of NiFe_2O_4 ceramic inert anode for aluminum electrolysis prepared in the different sintering atmosphere was carried out in Na_3AlF_6-Al_2O_3 melt.The results show that the corrosion rates of NiFe_2O_4 ceramic inert anodes prepared in the vacuum and the atmosphere with oxygen content of 1×10^(-2) are 6.08 cm/a and 2.59 cm/a,respectively.A densification layer is formed at the surface of anode due to some reactions which produce aluminates.For the anode prepared in the atmosphere with oxygen content of 1×10^(-2),the thickness of the densification layer(about 50 μm) is thicker than that(about 20 μm) formed at the surface of anode prepared in the vacuum.The content of NiO and Fe(Ⅱ) in Ni(Ⅱ)x Fe(Ⅱ)1-x Fe(Ⅲ)_2O_4 increases with the decrease of the oxygen content of sintering atmosphere,which reduces the corrosion resistance of the material.展开更多
The Al-3.40Mg-1.08Sc alloy plates were manufactured by selective laser melting(SLM) at platform temperatures of 35 ℃ and 200 ℃, respectively, and the corrosion performance of them was studied along height direction....The Al-3.40Mg-1.08Sc alloy plates were manufactured by selective laser melting(SLM) at platform temperatures of 35 ℃ and 200 ℃, respectively, and the corrosion performance of them was studied along height direction. The results show that the corrosion resistance of the alloy plate built at platform temperature of 35 ℃ along height direction is basically the same due to a uniform microstructure;While the corrosion resistance of the alloy plate built at platform temperature of 200 ℃ along height direction is different. The evolution of microstructure and the distribution of secondary phases are investigated, and the results show that the Cu-rich phases in alloy play a key role on corrosion performance. At higher platform temperature, the cooling rate is relative slow and a certain degree of in situ ageing leads to the significantly different distribution of Cu-rich phases along grain boundary. Specimens built at the platform temperature of 200 ℃ are inclined to locate at the crossed grain boundary, rather than continuous segregation of Cu-rich phases along grain boundary that is built at platform temperature of 35 ℃. Therefore, the corrosion resistance of Al-3.40Mg-1.08Sc alloy plate manufactured at platform temperature of 200 ℃ is higher, and presents a gradually decreasing trend along height direction.展开更多
基金Projects(51271169,51001089) supported by the National Natural Science Foundation of China
文摘Two additives of ethylene diamine tetraacetic acid （EDTA） and ammonium chloride （NH4C1） were separately used in the electrodeposition of Zn-Ni alloy films from a deep eutectic solvent. The effects of these two additives on electrodeposition behavior, composition, morphology, and corrosion performance of the Zn-Ni alloys were investigated. The electrodeposition behaviors of Zn-Ni alloy revealed by the cyclic voltammetry show that the addition of EDTA to the Zn-Ni electrolyte enhances the Zn incorporation into the alloy film while the addition of NH4C1 produces an opposite effect by suppressing Zn incorporation into the film. With an increase of EDTA concentration in the electrolyte, the Zn content of the Zn-Ni films increases, while the grain size of the deposits and the current efficiency of the plating process decrease. The increase of NH4C1 concentration in the electrolyte would significantly refine the grain size of the electrodeposited Zn-Ni films, reduce the Zn content and increase the cathodic current efficiency. The corrosion testing indicates that the barrier corrosion resistances of Zn-Ni films electrodeposited from NHnC1 containing electrolytes are superior to those electrodeposited from EDTA-containing electrolytes, which in turn are superior to those electrodeposited from additive-free electrolytes.
基金Project(AWPT08-10)supported by the Open Fund of the State Key Laboratory of Advanced Welding Production Technology in Harbin Institute of Technology,ChinaProject(mmlab0706)supported by the Open Fund of the State Key Laboratory of Materials Modification by Laser,Ion and Electron Beams in Dalian University of University,ChinaProject(0710908-05-K)supported by the Research Funds of the Guangxi Key Laboratory of Information Materials in Guilin University of Electronic Technology,China
文摘To improve the wear and corrosion properties of AZ91D magnesium alloys,Cu-based amorphous composite coatings were fabricated on AZ91D magnesium alloy by laser cladding using mixed powders of Cu47Ti34Zr11Ni8 and SiC.The wear and corrosion behaviours of the coatings were investigated.The wear resistance of the coatings was evaluated under dry sliding wear condition at room temperature.The corrosion resistance of the coatings was tested in 3.5%(mass fraction) NaCl solution.The coatings exhibit excellent wear resistance due to the recombined action of amorphous phase and different intermetallic compounds.The main wear mechanisms of the coatings and the AZ91D sample are different.The former is abrasive wear and the latter is adhesive wear.The coatings compared with AZ91D magnesium alloy also exhibit good corrosion resistance because of the presence of the amorphous phase in the coatings.
文摘The microstructure evolution, mechanical and corrosion properties of Al-11Si-2Cu-0.8Zn die cast alloy treated with Bi, Sb and Sr additions were investigated. The results of mechanical testing showed that all additions increased impact toughness, ultimate tensile strength, and elongation of the alloy as a result of change in eutectic Si morphology. The analysis of fracture surfaces revealed that with addition of Sr and to lesser extent Bi and Sb, the alloy exhibited a predominantly ductile fracture rather than quasi-cleavage brittle fracture. Moreover, with the additions of Sr, Bi and Sb, the quality index increased to 164.7 MPa, 156.3 MPa and 152.6 MPa respectively from 102 MPa for the base alloy. Polarization corrosion tests conducted in sodium chloride solution showed that the corrosion potential shifted to more negative values with additions of Sb, Bi and Sr, respectively. Corrosion immersion tests also revealed that the element additions have a detrimental effect on the corrosion rate of alloys, due to the increase of boundaries between the Al and eutectic Si phases.
基金Project(2020E0264) supported by the Xinjiang Science and Technology Project Plan of Autonomous Region,ChinaProject(2020D01C030) supported by the Autonomous Region Natural Science Foundation,China。
文摘In order to study the corrosion resistance of high-speed laser cladding(HLC) coating while improving production efficiency,a CoCrFeNiMo_(0.2)high-entropy alloy(HEA) coating was prepared by HLC.The optimized parameters of HLC are laser power of 880 W,scanning speed of 18 m/min,overlapping ratio of 60%,and powder feed speed of 3 r/min.Then,the surface roughness,microstructure,phase composition,element distribution,and electrochemical properties in 3.5 wt% NaCl solution of the coatings were analyzed,respectively.The local surface roughness of the CoCrFeNiMo_(0.2)HEA coating was found to be 15.53 μm.A distinct metallurgical bond could be observed between the coating and the substrate.Compared to the conventional laser cladding(CLC),the results of electrochemical tests showed that CoCrFeNiMo_(0.2)HEA coating exhibited a significant passivation.The corrosion current density of 5.4411 × 10^(-6)A·cm^(-2) and the corrosion potential of-0.7445 V for the HLC coating were calculated by the Tafel extrapolation method.The CLC coating’s corrosion current density and corrosion potential are 2.7083×10^(-5)A·cm^(-2) and-0.9685 V,respectively.The HLC coating shows a superior corrosion resistance,crucially due to the uniform and fine grains.Under various complex and harsh working conditions,this method can be widely used in the field of repairing and remanufacturing of corro sion-proof workpiece s.
文摘Two types of composites were prepared with Al-4.5Cu alloy as a matrix using stir casting method.One was reinforced with 10wt.%of Si C and 2wt.%of MoS2.The other was reinforced with 10wt.%of Si C and 4wt.%of MoS2.Their surfaces were remelted using a CO2 laser beam with an objective to study the influence of laser surface melting(LSM).The topography,microhardness,corrosion resistance and wear resistance of the laser melted surfaces were studied.Overall surface integrity after LSM was compared with as-cast surface.LSM enhanced the microhardness and wear resistance of the surface in each case.Porosity of the laser melted surface was low and corrosion resistance was high.Thus,LSM can be conveniently applied to enhancing the surface integrity of the aluminium composites.However,there is an optimum laser specific energy,around 38 J/m^2 in this study,for obtaining the best surface integrity.
基金Projects(51474238,51334002)supported by the National Natural Science Foundation of China
文摘A comparative study on the corrosion resistance of NiFe_2O_4 ceramic inert anode for aluminum electrolysis prepared in the different sintering atmosphere was carried out in Na_3AlF_6-Al_2O_3 melt.The results show that the corrosion rates of NiFe_2O_4 ceramic inert anodes prepared in the vacuum and the atmosphere with oxygen content of 1×10^(-2) are 6.08 cm/a and 2.59 cm/a,respectively.A densification layer is formed at the surface of anode due to some reactions which produce aluminates.For the anode prepared in the atmosphere with oxygen content of 1×10^(-2),the thickness of the densification layer(about 50 μm) is thicker than that(about 20 μm) formed at the surface of anode prepared in the vacuum.The content of NiO and Fe(Ⅱ) in Ni(Ⅱ)x Fe(Ⅱ)1-x Fe(Ⅲ)_2O_4 increases with the decrease of the oxygen content of sintering atmosphere,which reduces the corrosion resistance of the material.
基金Project(51901207) supported by the National Natural Science Foundation of ChinaProject(2018M632796) supported by the China Postdoctoral Science FoundationProjects(19A430024, 21A430037) supported by the Plan of Henan Key Scientific Research Project of Universities,China。
文摘The Al-3.40Mg-1.08Sc alloy plates were manufactured by selective laser melting(SLM) at platform temperatures of 35 ℃ and 200 ℃, respectively, and the corrosion performance of them was studied along height direction. The results show that the corrosion resistance of the alloy plate built at platform temperature of 35 ℃ along height direction is basically the same due to a uniform microstructure;While the corrosion resistance of the alloy plate built at platform temperature of 200 ℃ along height direction is different. The evolution of microstructure and the distribution of secondary phases are investigated, and the results show that the Cu-rich phases in alloy play a key role on corrosion performance. At higher platform temperature, the cooling rate is relative slow and a certain degree of in situ ageing leads to the significantly different distribution of Cu-rich phases along grain boundary. Specimens built at the platform temperature of 200 ℃ are inclined to locate at the crossed grain boundary, rather than continuous segregation of Cu-rich phases along grain boundary that is built at platform temperature of 35 ℃. Therefore, the corrosion resistance of Al-3.40Mg-1.08Sc alloy plate manufactured at platform temperature of 200 ℃ is higher, and presents a gradually decreasing trend along height direction.
