CFRP （carbon fiber reinforced plastic）, which is composed of carbon fibers in a resin matrix, is an extremely strong and light composite material that has found use in the aerospace and automotive industries. CFRP b...CFRP （carbon fiber reinforced plastic）, which is composed of carbon fibers in a resin matrix, is an extremely strong and light composite material that has found use in the aerospace and automotive industries. CFRP boards are very difficult to machine using common machining processes. Various machining artifacts, such as burrs and delamination, occur frequently when machining CFRP. Adequate techniques for machining CFRP have not yet been established. Recently, electroplated diamond wire machining technology has found use in cutting hard, brittle materials such as silicon and sapphire. In this study, we used an electroplated diamond wire saw to cut a CFRP workpiece. We quantified the cutting forces imposed on the workpiece and observed the surface state of the workpiece after cutting. We demonstrated that an electroplated diamond wire tool is suitable for the high-quality machining of CFRP boards.展开更多
Electrical steel sheets with 6.5%(mas fraction) Si with good shapes and superior magnetic inductions were successfully produced by a specially designed processing route including ingot casting, hot rolling and warm ro...Electrical steel sheets with 6.5%(mas fraction) Si with good shapes and superior magnetic inductions were successfully produced by a specially designed processing route including ingot casting, hot rolling and warm rolling both with interpass thermal treatment, and final annealing. The sheets were of 0.2 mm and 0.3 mm thick over 140 mm width. A detailed study of the microstructural and textural evolutions from the hot rolling to annealing was carried out by optical microscopy, X-ray diffraction and electron backscattered diffraction. The hot rolled sheet characterized by near-equiaxed grains was dominated by the mixture of <001>//ND fiber(λ-fiber), <110>//RD fiber(α-fiber) and <111>//ND fiber(γ-fiber) textures owing to the partial recrystallization and strain induced boundary migration(SIBM) during the hot rolling interpass thermal treatment. The static recovery and SIBM during the warm rolling interpass thermal treatment result in large and elongated warm rolling grains. The warm rolling texture is dominated by obvious λ, Goss and strong γ-fiber textures. The application of the interpass thermal treatment during hot and warm rolling significantly enhances the impact of SIBM during annealing, which is responsible for the formation of the moderate λ-fiber, some near-λ fiber texture components and the obviously weakened γ-fiber texture in the annealed sheet, leading to a higher magnetic induction compared to the commercially produced 6.5% Si steel by chemical vapor deposition(CVD).展开更多
文摘CFRP （carbon fiber reinforced plastic）, which is composed of carbon fibers in a resin matrix, is an extremely strong and light composite material that has found use in the aerospace and automotive industries. CFRP boards are very difficult to machine using common machining processes. Various machining artifacts, such as burrs and delamination, occur frequently when machining CFRP. Adequate techniques for machining CFRP have not yet been established. Recently, electroplated diamond wire machining technology has found use in cutting hard, brittle materials such as silicon and sapphire. In this study, we used an electroplated diamond wire saw to cut a CFRP workpiece. We quantified the cutting forces imposed on the workpiece and observed the surface state of the workpiece after cutting. We demonstrated that an electroplated diamond wire tool is suitable for the high-quality machining of CFRP boards.
基金Projects(51004035,51374002,50734001)supported by the National Natural Science Foundation of ChinaProject(2012BAE03B00)supported by the National Key Technology R&D Program,China+1 种基金Project(2012AA03A506)supported by the High-tech R&D Program,ChinaProject(N120407009)supported by the Fundamental Research Funds for the Central Universities,China
文摘Electrical steel sheets with 6.5%(mas fraction) Si with good shapes and superior magnetic inductions were successfully produced by a specially designed processing route including ingot casting, hot rolling and warm rolling both with interpass thermal treatment, and final annealing. The sheets were of 0.2 mm and 0.3 mm thick over 140 mm width. A detailed study of the microstructural and textural evolutions from the hot rolling to annealing was carried out by optical microscopy, X-ray diffraction and electron backscattered diffraction. The hot rolled sheet characterized by near-equiaxed grains was dominated by the mixture of <001>//ND fiber(λ-fiber), <110>//RD fiber(α-fiber) and <111>//ND fiber(γ-fiber) textures owing to the partial recrystallization and strain induced boundary migration(SIBM) during the hot rolling interpass thermal treatment. The static recovery and SIBM during the warm rolling interpass thermal treatment result in large and elongated warm rolling grains. The warm rolling texture is dominated by obvious λ, Goss and strong γ-fiber textures. The application of the interpass thermal treatment during hot and warm rolling significantly enhances the impact of SIBM during annealing, which is responsible for the formation of the moderate λ-fiber, some near-λ fiber texture components and the obviously weakened γ-fiber texture in the annealed sheet, leading to a higher magnetic induction compared to the commercially produced 6.5% Si steel by chemical vapor deposition(CVD).
