电加热高光注塑模具设计

一种高光注塑模具在模芯内设有电加热件,在模芯上设有隔热槽,同时在模具主体与模芯之间设有隔热板,使其在实现高光注塑的同时,大幅地降低了能耗。该工艺方法的设计研究,具有显著的科研和工程实用价值。

CUTTING TEMPERATURE MEASUREMENT IN HIGH-SPEED END MILLING

A computer aided measurement system is used to measure the cutting temperature directly in high-speed machining by natural thermocouples and standard thermocouples. In this system the tool/workpiece interface temperature is measured by the tool/workpiece natural thermocouple, while the temperature distribution on the workpiece surface and that of interior are measured by some standard thermocouples prearranged at proper positions. The system can be used to measure cutting temperature in the machining with the rotary cutting tools, such as vertical drill and end milling cutter. It is practically used for the research on high-speed milling with hardened steel.

Experimental investigation on performance of intumescent coating for steel plate at elevated temperature

Twenty tests were conducted to investigate the efficiency of the intumescent coating designed to protect steel plate at the elevated temperature, by means of electrical furnace. And the factors of the initial thickness of coating and temperature of electrical furnace were considered. The high temperature response behavior of the intumescent coating was observed. And the expansion form of ultrathin intumescent coating and the temperature of the steel plate(TS) were obtained. Besides, the heat flux from expansion layer to steel plate versus time was analyzed in order to evaluate the heat transfer effect of intumescent coating on steel plate. The experimental results show that the response behaviors of the coating subjected to fire could be divided into four phases: stabilization phase, foaming expansion phase, carbonization-consumption phase and inorganic layer phase. And the net heat flux to the steel plate decreased observably in the foaming expansion phase, while the surplus white inorganic substance, which is the residue of the intumesced char layer in the inorganic layer phase under the condition of the temperature of the electrical furnace(TEF) beyond 700 °C over 1 h, has little effect on fire protection for the steel plate.

Investigating Two Configurations of a Heat Exchanger in an Indirect Heating Integrated Collector Storage Solar Water Heating System

Due to the environmental impact of energy usage and increased price of fusel fuel, consumers need to be encouraged to use renewable energy sources. The IHICSSWHS （indirect heating integrated collector storage solar water heater system） is one of the most economical systems. It incorporates the collection of a solar energy component and a hot water storage component in one unit. The objective of this study was to investigate ways to enhance the thermal performance of the system. Two configurations of the system were studied： system with double row HX （heat exchanger） and tube length of 16.2 m, and system with single row HX and tube length of 8.1 m and 10.8 m. The service water tube inside diameter was also varied to 10.7 mm and 17.1 mm The steady state continuity, momentum and energy equations were numerically solved, using FLUENT software. A standard k-w turbulent model and surface-to-surface radiation model were used. The result showed that the system of 10.8 m tube length and single row HX provided higher outlet temperature than the system of 16.2 m and double row HX. Therefore, a significant reduction in cost and power usage can be achieved by using a single row HX.

A preliminary experimental validation of superposition strategy in thermal management of integrated circuit with multiple hot-spots

Thermal management is a key issue in the integrated circuit(IC)design.In this paper,the superposition strategy was experimentally validated using a modeling IC device,which was fabricated by laboratory-level microfabrication technique.Metal thin film resistors on the top of dielectric layer were used to analogize the multiple hot-spots in the modeling IC device.The measured temperature rise with multiple hot-spots agrees well with the predictions given by the superposition calculations.With the help of the superposition strategy,thermal management of IC device can be significantly simplified by decomposing the system into sub-systems and optimizing each part individually.The influence coefficients in the superposition strategy extracted from the experimental measurement offer the IC designers a useful engineering tool to facility the thermal optimization and evaluate the thermal performance of IC devices.