Anodic behaviors and oxygen evolution kinetics of Pb-0.8%Ag and Al/Pb-0.8%Ag anodes during the initial 24 h zinc electrowinning were investigated with cyclic voltammetry （CV） curves and electrochemical impedance spe...Anodic behaviors and oxygen evolution kinetics of Pb-0.8%Ag and Al/Pb-0.8%Ag anodes during the initial 24 h zinc electrowinning were investigated with cyclic voltammetry （CV） curves and electrochemical impedance spectroscopy （EIS）. The results reveal that the anodic behaviors and reaction kinetics of the two anodes vary a lot during the anodic polarization which indicate the formation and stabilization of anodic layer. Compared with conventional Pb-0.8%Ag anode, A1/Pb-0.8%Ag anode has longer time of anodic polarization. At the very beginning of anodic polarization, the two anodes all exhibit higher potential of oxygen evolution reaction （OER） since the reaction is controlled by the transformation step of intermediates. Then, its OER potential is largely diminished and OER rate is deduced from the formation and adsorption of the first intermediate （S-OHms）. In the prolonged anodie polarization, the anodie potential of A1/Pb-0.8%Ag gradually decreases and the final value is more stable than that of conventional Pb-0.8%Ag anode. On the anodic layer after 24 h of anodic polarization, the OER potential is controlled by the formation and adsorption of intermediate. The microstructures of A1/Pb-0.8%Ag and Pb-0.8%Ag anodes after 24 h of anodie polarization were analyzed by scanning electron microscope （SEM）.展开更多
The effects of adding alloy element zinc on the static and dynamic mechanical properties of copper-zinc alloy were investigated. Tensile and low cycle fatigue behaviors of the C11000 copper and H63 copper-zinc alloy w...The effects of adding alloy element zinc on the static and dynamic mechanical properties of copper-zinc alloy were investigated. Tensile and low cycle fatigue behaviors of the C11000 copper and H63 copper-zinc alloy were obtained by using a miniature tester that combined the functions of in situ tensile and fatigue testing. A piezoelectric actuator was adopted as the actuator for the fatigue testing, and the feasibility of the fatigue actuator was verified by the transient harmonic response analysis based on static tensile preload and dynamic sinusoidal load. The experimental results show that the yield strength and tensile strength of the C11000 copper are improved after adding 37%(mass fraction) zinc, and H63 copper-zinc alloy presents more obvious cyclic hardening behavior and more consumed irreversible plastic work during each stress cycle compared with C11000 copper for the same strain controlled cycling. Additionally, based on the Manson-Coffin theory, the strain-life equations of the two materials were also obtained. C11000 copper and H63 copper-zinc alloy show transition life of 16832 and 1788 cycles, respectively.展开更多
基金Project(51004056)supported by the National Natural Science Foundation of China
文摘Anodic behaviors and oxygen evolution kinetics of Pb-0.8%Ag and Al/Pb-0.8%Ag anodes during the initial 24 h zinc electrowinning were investigated with cyclic voltammetry （CV） curves and electrochemical impedance spectroscopy （EIS）. The results reveal that the anodic behaviors and reaction kinetics of the two anodes vary a lot during the anodic polarization which indicate the formation and stabilization of anodic layer. Compared with conventional Pb-0.8%Ag anode, A1/Pb-0.8%Ag anode has longer time of anodic polarization. At the very beginning of anodic polarization, the two anodes all exhibit higher potential of oxygen evolution reaction （OER） since the reaction is controlled by the transformation step of intermediates. Then, its OER potential is largely diminished and OER rate is deduced from the formation and adsorption of the first intermediate （S-OHms）. In the prolonged anodie polarization, the anodie potential of A1/Pb-0.8%Ag gradually decreases and the final value is more stable than that of conventional Pb-0.8%Ag anode. On the anodic layer after 24 h of anodic polarization, the OER potential is controlled by the formation and adsorption of intermediate. The microstructures of A1/Pb-0.8%Ag and Pb-0.8%Ag anodes after 24 h of anodie polarization were analyzed by scanning electron microscope （SEM）.
基金Projects(51275198,51422503)supported by the National Natural Science Foundation of ChinaProject(2012YQ030075)supported by Special Funds for Development of National Major Scientific Instruments and Equipments,China+1 种基金Project(NECT-12-0238)supported by Program for New Century Excellent Talents in University,ChinaProject(20150520108JH)supported by Young Scientist Fund of Jilin Province of China
文摘The effects of adding alloy element zinc on the static and dynamic mechanical properties of copper-zinc alloy were investigated. Tensile and low cycle fatigue behaviors of the C11000 copper and H63 copper-zinc alloy were obtained by using a miniature tester that combined the functions of in situ tensile and fatigue testing. A piezoelectric actuator was adopted as the actuator for the fatigue testing, and the feasibility of the fatigue actuator was verified by the transient harmonic response analysis based on static tensile preload and dynamic sinusoidal load. The experimental results show that the yield strength and tensile strength of the C11000 copper are improved after adding 37%(mass fraction) zinc, and H63 copper-zinc alloy presents more obvious cyclic hardening behavior and more consumed irreversible plastic work during each stress cycle compared with C11000 copper for the same strain controlled cycling. Additionally, based on the Manson-Coffin theory, the strain-life equations of the two materials were also obtained. C11000 copper and H63 copper-zinc alloy show transition life of 16832 and 1788 cycles, respectively.
