Direct methanol fuel cells (DMFCs) are promising for use in portable devices because of advantages such as high fuel energy density, low working temperature and low emission of pollutants. Nanotechnology has been us...Direct methanol fuel cells (DMFCs) are promising for use in portable devices because of advantages such as high fuel energy density, low working temperature and low emission of pollutants. Nanotechnology has been used to improve the performance of DMFCs. Catalytic materials composed of small, metallic particles with unique nanostructure supparted on carbons or metal oxides have been widely investigated for use in DMFCs. Despite our increased understanding of this type of fuel cell, many challenges still remain. This paper reviews the current developments of nanostructured elec- trocatalytic materials and porous electrodes for use in DMFCs. In particular, this review focuses on the synthesis and characterization of nanostructured catalysts and supporting materials. Both computational and experimental approaches to optimize mass transportation in porous electrodes of DMFCs, such as theoretical modeling of internal transfer processes and preparation of functional structures in membrane electrode assemblies, are introduced.展开更多
The mechanical properties and stress corrosion cracking (SCC) resistance of an Al-Zn-Cu-Mg-Sc-Zr alloy under different aging conditions were investigated. The dependence of microstrueture and mechanical properties o...The mechanical properties and stress corrosion cracking (SCC) resistance of an Al-Zn-Cu-Mg-Sc-Zr alloy under different aging conditions were investigated. The dependence of microstrueture and mechanical properties on aging parameters was evaluated by tensile test, hardness test and conductivity measurement. The results show that for the alloys with retrogression and re-aging treatment (RRA), the conductivity increases with the retrogression time and temperature, while the tensile strength decreases. The transmission electron microscopy (TEM) results show that the precipitates η(MgZn2) at grain boundary aggregate apparently with retrogression time and the precipitates inside the matrix exhibit the similar distribution to T6 temper, which comprises fine GP zones, large η'(MgZn2)and η(MgZn2) phases. According to the mechanical properties and microstructure observations, the optimal RRA regime is recommended to be 120℃, 24h + 180 ℃, 30 min + 120 ℃, 24 h. The strength level of the alloy after the optimum RRA treatment is similar to that in T6 condition and the SCC resistance is improved obviously in contrast to T6 condition.展开更多
Owing to both of its high carrier concentration and large band gap, ZnO:Al (ZAO) films which is an n-type degenerate semiconductor, exhibits low resistance and high transmittance in the visible range. This work studie...Owing to both of its high carrier concentration and large band gap, ZnO:Al (ZAO) films which is an n-type degenerate semiconductor, exhibits low resistance and high transmittance in the visible range. This work studies the crystal structure, optical and electrical properties and preparation methods of ZAO films, and discusses the existing problems and application prospective of ZAO films.展开更多
Tensile tests with small deformation amounts of 0.5%,1%,3%and 5%were performed at room temperature on as cast Mg-1%Al alloy.Microstructures of the Mg-1%Al alloys before and after deformation were observed by optical m...Tensile tests with small deformation amounts of 0.5%,1%,3%and 5%were performed at room temperature on as cast Mg-1%Al alloy.Microstructures of the Mg-1%Al alloys before and after deformation were observed by optical microscopy(OM) and transmission electron microscopy(TEM).The strain amplitude dependent and temperature dependent damping capacities of the as-cast and deformed Mg-1%Al alloys were investigated by dynamic mechanical analysis(DMA).The mechanism of deformation on damping capacity of Mg-1%Al alloy was discussed.The results show that the as-cast Mg-1%Al alloy has high damping value at high strain.When the tensile elongation is higher than 3%,the damping values of this alloy in high strain region are significantly decreased at room temperature.But the large amount of dislocations produced by tensile deformation are activated by heat,and then increase the damping value at high temperature.展开更多
In this work,we describe a novel facile method to prepare long one-dimensional hybrid nanofibers by using hydrated bacterial cellulose nanofibers(BCF)as a template.Silver(Ag)nanoparticles with an average diameter of 1...In this work,we describe a novel facile method to prepare long one-dimensional hybrid nanofibers by using hydrated bacterial cellulose nanofibers(BCF)as a template.Silver(Ag)nanoparticles with an average diameter of 1.5 nm were well dispersed on BCF via a simple in situ chemical-reduction between AgNO3and NaBH4at a relatively low temperature.A growth mechanism is proposed that Ag nanoparticles are uniformly anchored onto BCF by coordination with BC-containing hydroxyl groups.The bare BCF and as-prepared Ag/BCF hybrid nanofibers were characterized by several techniques including transmission electron microscopy,X-ray diffraction,thermogravimetric analyses,and ultraviolet-visible(UV-Vis)absorption spectra.The antibacterial properties of Ag/BCF hybrid nanofibers against Escherichia coli(E.coli,Gram-negative)and Staphylococcu saureus(S.saureus,Gram-positive)bacteria were evaluated by using modified Kirby Bauer method and colony forming count method.The results show that Ag nanoparticles are well dispersed on BCF surface via in situ chemical-reduction.The Ag/BCF hybrid nanofiber presents strong antibacterial property and thus offers its candidature for use as functional antimicrobial agents.展开更多
A simple strategy to prepare a hybrid of nanocomposites of anatase TiO2/graphene nanosheets (GNS) as anode materials for lithium-ion batteries was reported.The morphology and crystal structure were studied by X-ray ...A simple strategy to prepare a hybrid of nanocomposites of anatase TiO2/graphene nanosheets (GNS) as anode materials for lithium-ion batteries was reported.The morphology and crystal structure were studied by X-ray diffraction (XRD),field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM).The electrochemical performance was evaluated by galvanostatic charge-lischarge tests and alternating current (AC) impedance spectroscopy.The results show that the TiO2/GNS electrode exhibit higher electrochemical performance than that of TiO2 electrode regardless of the rate.Even at 500 mA/g,the capacity of TiO2/GNS is 120.3 mAh/g,which is higher than that of TiO2 61.6 mAh/g.The high performance is attributed to the addition of graphene to improve electrical conductivity and reduce polarization.展开更多
In order to improve the electrochemical hydrogen storage performance of the Mg2Ni-type electrode alloys, Mg in the alloy was partially substituted by La, and the nanocrystalline and amorphous Mg2Ni-type Mg20-xLaxNi10 ...In order to improve the electrochemical hydrogen storage performance of the Mg2Ni-type electrode alloys, Mg in the alloy was partially substituted by La, and the nanocrystalline and amorphous Mg2Ni-type Mg20-xLaxNi10 (x-=0, 2) alloys were synthesized by melt-spinning technique. The microstructures of the as-spun alloys were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The electrochemical hydrogen storage properties of the experimental alloys were tested. The results show that no amorphous phase is detected in the as-spun Mg20Ni10 alloy, but the as-spun Mg18La2Ni10 alloy holds a major amorphous phase. As La content increases from 0 to 2, the maximum discharge capacity of the as-spun (20 m/s) alloys rises from 96.5 to 387.1 mA.h/g, and the capacity retaining rate (S20) at the 20th cycle grows from 31.3% to 71.7%. Melt-spinning engenders an impactful effect on the electrochemical hydrogen storage performances of the alloys. With the increase in the spinning rate from 0 to 30 m/s, the maximum discharge capacity increases from 30.3 to 135.5 mA.h/g for the Mg20Ni10 alloy, and from 197.2 to 406.5 mA-h/g for the Mg18La2Ni10 alloy. The capacity retaining rate (S20) of the Mg2oNi10 alloy at the 20th cycle slightly falls from 36.7% to 27.1%, but it markedly mounts up from 37.3% to 78.3% for the Mg18La2Ni10 alloy.展开更多
As a preliminary investigation towards obtaining carbon nanotube composite adsorbent for CO2 capture, in this study CO2 adsorption performance of three commercial carbon nanotubes (CNTs) one single-walled carbon nan...As a preliminary investigation towards obtaining carbon nanotube composite adsorbent for CO2 capture, in this study CO2 adsorption performance of three commercial carbon nanotubes (CNTs) one single-walled carbon nanotubes (SWCNTs), and two (2) different multi-walled carbon nanotubes (referred to as A-MWCNTs and B-MWCNTs) were evaluated and compared. The purpose of this study was to compare the different types of CNTs and select the best to serve as the solid anchor in the development of a hydrophobic composite adsorbent material for CO2 capture. The N2 physi- sorption of the CNTs was conducted to determine their surface area, pore volume and pore size. In addition, morphology and purity of the CNTs were checked with Transmission Electron Microscopy and Raman Spectroscopy, respectively. The CO2 adsorption capacity of the CNTs was evaluated using Thermo-gravimetric analysis (TGA) at 1.1 bar, at operating temperature ranged from 25 to 55 ~C and at different CO2 feed flow rates, in order to evaluate the effects of these variables on the CO2 adsorption capacity. The results of CO2 adsorption with the TGA show that CO2 adsorption capacity for both SWCNTs and MWCNTs was the highest at 25 ~C. Changing the CO2 flowrates had no significant effect on the adsorption capacity of MWCNTs, but decreasing the CO2 flow rate resulted in the enhancement of the CO2 adsorption capacity of SWCNTs. Overall, it was found that the SWCNTs displayed the highest CO2 adsorption capacity (29.97 gCO2/kg ad- sorbent) when compared to the MWCNTs (12.09 gCO2/kg adsorbent), indicating a 150% increase in adsorption capacity over MWCNTs.展开更多
Analytical solutions for a Griffith crack inside an infinite piezoel ectromagnetic medium under combined mechanical-electrical-magnetic loadings are formulated using integral transform method. The singular stress, ele...Analytical solutions for a Griffith crack inside an infinite piezoel ectromagnetic medium under combined mechanical-electrical-magnetic loadings are formulated using integral transform method. The singular stress, electric and magnetic fields in the piez oelectromagnetic material are obtained by the theory of linear piezoelectromagneticity. Fourier transforms are used to reduce the mixed boundary value problems of the crack, which is assumed to b e permeable, to dual integral equations. The solution of the dual integral equations is then ex pressed analytically. Expressions for strains, stresses, electric fields, electric displacements, mag netic fields and magnetic inductions in the vicinity of the crack tip are derived. Field intensi ty factors and energy release rate for piezoelectromagnetic material are obtaine d. The stresses, electric displacements and magnetic inductions at the crack tip show the traditional square root singu larities; and the electric field intensity factor (EFIF) and the magnetic field intensity factor (MFIF) are always zero.展开更多
The effects of Yb content on the microstructures and mechanical properties of 2519A aluminum alloy plate were investigated by means of tensile test,optical microscopy,transmission electron microscopy,scanning electron...The effects of Yb content on the microstructures and mechanical properties of 2519A aluminum alloy plate were investigated by means of tensile test,optical microscopy,transmission electron microscopy,scanning electron microscopy and X-ray diffractometer.The results show that addition of 0.17% (mass fraction) Yb increases the density of θ' particles of the 2519A alloy plate and reduces the coarsening speed rate of θ' phase at 300 ℃.Therefore,tensile strength is enhanced from 483.2 MPa to 501.0 MPa at room temperature and is improved from 139.5 MPa to 169.4 MPa at 300 ℃.The results also show that with the addition of 0.30% (mass fraction) Yb,the mechanical properties increase at 300 ℃ and decrease at room temperature.With Yb additions,the Al7.4Cu9.6Yb2 phase is found whilst the segregated phases of as-cast alloys along grain boundaries become discontinuous,thin and spheroidized.展开更多
This paper relates to highly dispersed supported Pd/MWCNTs and Fd/a-Al2O3 catalysts prepared by biological reduction method. The physico-chemical properties and the difference in catalytic activity of Pd catalysts pre...This paper relates to highly dispersed supported Pd/MWCNTs and Fd/a-Al2O3 catalysts prepared by biological reduction method. The physico-chemical properties and the difference in catalytic activity of Pd catalysts prepared by bio- logical reduction method and chemical method, respectively, were investigated using XRD, TEM and specific surface char- acterization methods. The catalytic properties of catalysts were studied through activity evaluation means. The test results showed that the catalysts prepared by biological method were characteristic of small Pd nanoparticle size, good dispersion and low agglomeration, while possessing a high activity and stability in styrene hydrogenation reaction in comparison with catalysts prelgared via the chemical method.展开更多
The influence of exfoliation corrosion on the tensile properties of a high strength Al-Zn-Mg-Cu alloy was investigated by ambient temperature tensile testing, optical microscopy, transmission electron microscopy (TEM...The influence of exfoliation corrosion on the tensile properties of a high strength Al-Zn-Mg-Cu alloy was investigated by ambient temperature tensile testing, optical microscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). After exfoliation corrosion immersion, blisters and corrosion pits can be seen on the sheet surface, which lead to loss of materials and notches. A number of intergranular cracks are observed to initiate at the bottom of the corrosion-induced notches and propagate rapidly into the bulk materials during tensile. Consequently, exfoliation corrosion results in significant loss of strength and brittle fracture. EBSD results show that the crack propagation path is primarily along the grain boundaries with misorientation of-45°, and coincidence site lattice (CSL) boundaries are slightly more resistant to crack.展开更多
Large surface areas nano-scale zirconia was prepared by the self-assembly route and was employed as support in nickel catalysts for the CO selective methanation. The effects of Ni loading and the catalyst calcination ...Large surface areas nano-scale zirconia was prepared by the self-assembly route and was employed as support in nickel catalysts for the CO selective methanation. The effects of Ni loading and the catalyst calcination temperature on the performance of the catalyst for CO selective methanation reaction were investigated. The cata- lysts were characterized by Brunauer-Emmett-Teller (BET), transmission electron microscope (TEM), X-ray dif- fraction (XRD) and temperature-programmed reduction (TPR). The results showed that the as-synthesized Ni/nano-ZrO2 catalysts presented high activity for CO methanation due to the interaction between Ni active particle and nano zir- conia support. The selectivity for the CO methanation influenced significantly by the particle size of the active Ni species. The exorbitant calcination resulted in the conglomeration of dispersive Ni particles and led to the decrease of CO methanation selectivity. Among the catalysts studied, the 7.5% (by mass) Ni/ZrO2 catalyst calcinated at 500℃ was the most effective for the CO selective methanation. It can preferentially catalyze the CO methanation with a higher 99% conversion in the CO/CO2 competitive methanation system over the temperature range of 260-280℃, while keeping the CO2 conversion relatively low.展开更多
The effect of Zn addition on the microstructure, tensile properties and electrochemical properties of as-annealed 3003 Al alloy was investigated through TEM observations, tensile tests and Tafel polarization analysis....The effect of Zn addition on the microstructure, tensile properties and electrochemical properties of as-annealed 3003 Al alloy was investigated through TEM observations, tensile tests and Tafel polarization analysis. High density precipitates are observed in the Zn-containing alloys and the alloy with 1.8% Zn addition also has rod-like precipitates. Tensile test results indicate that Zn has a great effect on tensile strength of 3003 Al alloy. The alloy with 1.5% Zn addition has the highest ultimate tensile strength. The electrochemical results indicate that Zn addition to 3003 Al alloy also has great impact on the corrosion potential of the 3003 A1 alloy in 0.5% NaCl solution and ethylene glycol-water solution. The corrosion potential varies with the Zn content and shifts negatively.展开更多
The main goal of this work is to explore the possibility of using Au-modified hydroxyapatite(HA) as a potential sensor material. Tube-like HA structure was fabricated with the aid of a Nafion N-117 cation exchange mem...The main goal of this work is to explore the possibility of using Au-modified hydroxyapatite(HA) as a potential sensor material. Tube-like HA structure was fabricated with the aid of a Nafion N-117 cation exchange membrane and gold(Au) nanoparticles were added by a hydrothermal method. The morphology, structure and composition were characterized by scanning electron microscopy(SEM), transmission electron microscopy(TEM), X-ray diffraction(XRD), and X-ray photoelectron spectroscopy(XPS). The gas sensing properties were also investigated. Results show that Au nanoparticles are dispersed into the HA powder, which is tube-like, with rough inner and outer surfaces. Compared with pure HA, Au-modified HA exhibits improved sensing properties for NH_3. 5%(mass fraction) Au-modified HA shows the highest response with relatively short response/recovery time. The response is up to 79.2% when the corresponding sensor is exposed to 200×10^(-6) NH_3 at room temperature, and the response time and recovery time are 20 s and 25 s, respectively. For lower concentration, like 50×10^(-6), the response is still up to 70.8%. Good selectivity and repeatability are also observed. The sensing mechanism of high response and selectivity for NH_3 gas was also discussed. These results suggest that Au-HA composite is a promising material for NH_3 sensors operating at room temperature.展开更多
This article mainly discussed bulk material lHvl^ared by powder metallurgy, and the commercial 2024 aluminum alloy powder and FeNiCrCoA13 high entropy alloy powder (both produced by argon gas atomization process) we...This article mainly discussed bulk material lHvl^ared by powder metallurgy, and the commercial 2024 aluminum alloy powder and FeNiCrCoA13 high entropy alloy powder (both produced by argon gas atomization process) were ball-milled for different hours. The prepared powder was consolidated by hot extrusion method. The microstruetures of the milled powder and bulk alloy were examined by X - Ray Diffraction (XRD), Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM). The thermal stability was tested by differential scanning calorimetry (DSC). Mechanical properties of the extruded alloy were examined by Vickers hardness tester and mechanical testing machine. The results show that after milling, the mixed particle sizes and microstructures of the alloy powder change obviously. The compressive strength of the extruded alloy has reached 580 MPa under certain conditions of milling time and composition.展开更多
The microstructures and mechanical properties of Al-6Zn-2Mg-1.5Cu-0.4Er alloy under different treatment conditions were investigated by transmission electron microscopy (TEM) observation, and tensile properties and ...The microstructures and mechanical properties of Al-6Zn-2Mg-1.5Cu-0.4Er alloy under different treatment conditions were investigated by transmission electron microscopy (TEM) observation, and tensile properties and hardness test, respectively. The relationship between mechanical properties and microstructures of the alloys was discussed. With trace Er addition to A1-Zn-Mg-Cu alloy, Er and Al interact to form Al3Er phase, which is coherent with a(A1) matrix. The results show that Al-Zn-Mg-Cu alloy after retrogression and re-ageing (RRA) heat treatment exhibits higher tensile strength, ductility and conductivity.展开更多
Transmission electron microscopy and surface- and bulk-sensitive spectroscopic methods were used to study the morphology and the electronic structure of a hybrid organic-inorganic system composed of gold nanoparticles...Transmission electron microscopy and surface- and bulk-sensitive spectroscopic methods were used to study the morphology and the electronic structure of a hybrid organic-inorganic system composed of gold nanoparticles (NP's) which were distributed in an organic matrix. Au atoms deposited onto a copper phthalocyanine (CuPc) surface diffuse into the organic matrix and self-assemble in well defined NP's with metallic properties. No formation of a continuous metallic Au film on top of the CuPc film is observed up to nominal coverages as large as 130 A.展开更多
In order to develop an excellent pseudocapacitor with both high specific capacitance and outstanding stretchability to match with other devices applicable in future wearable and bio-implantable systems, we focus our s...In order to develop an excellent pseudocapacitor with both high specific capacitance and outstanding stretchability to match with other devices applicable in future wearable and bio-implantable systems, we focus our studies on three vital aspects: Stretchability of hybrid film electrodes, the interface between different components, and the integrated performance in stretchability and electrochemistry of supercapacitors based on single-walled carbon nanotube/ polyaniline (SWCNT/PANI) composite films on pre-elongated elastomers. Owing to the moderate porosity, the buckled hybrid film avoids the cracking which occurs in conventional stretchable hybrid electrodes, and both a high specific capacitance of 435 F.g-1 and a high strain tolerance of 140% have been achieved. The good SWCNT/PANI interfacial coupling and the reinforced solid electrolyte penetration structure enable the integrated pseudocapacitors to have stretch- resistant interfaces between different units and maintain a high performance under a stretching of 120% elongation, even after 1,000 cyclic elongations.展开更多
基金supported by the National Natural Science Foundation of China(51274028)~~
文摘Direct methanol fuel cells (DMFCs) are promising for use in portable devices because of advantages such as high fuel energy density, low working temperature and low emission of pollutants. Nanotechnology has been used to improve the performance of DMFCs. Catalytic materials composed of small, metallic particles with unique nanostructure supparted on carbons or metal oxides have been widely investigated for use in DMFCs. Despite our increased understanding of this type of fuel cell, many challenges still remain. This paper reviews the current developments of nanostructured elec- trocatalytic materials and porous electrodes for use in DMFCs. In particular, this review focuses on the synthesis and characterization of nanostructured catalysts and supporting materials. Both computational and experimental approaches to optimize mass transportation in porous electrodes of DMFCs, such as theoretical modeling of internal transfer processes and preparation of functional structures in membrane electrode assemblies, are introduced.
基金Project(2006AA03Z523) supported by the National High-tech Research and Development Program of China
文摘The mechanical properties and stress corrosion cracking (SCC) resistance of an Al-Zn-Cu-Mg-Sc-Zr alloy under different aging conditions were investigated. The dependence of microstrueture and mechanical properties on aging parameters was evaluated by tensile test, hardness test and conductivity measurement. The results show that for the alloys with retrogression and re-aging treatment (RRA), the conductivity increases with the retrogression time and temperature, while the tensile strength decreases. The transmission electron microscopy (TEM) results show that the precipitates η(MgZn2) at grain boundary aggregate apparently with retrogression time and the precipitates inside the matrix exhibit the similar distribution to T6 temper, which comprises fine GP zones, large η'(MgZn2)and η(MgZn2) phases. According to the mechanical properties and microstructure observations, the optimal RRA regime is recommended to be 120℃, 24h + 180 ℃, 30 min + 120 ℃, 24 h. The strength level of the alloy after the optimum RRA treatment is similar to that in T6 condition and the SCC resistance is improved obviously in contrast to T6 condition.
基金Funded by the foundation for key projects in 2000 of the Science and Technology Committee of Chongqing China (No.2000-6214).
文摘Owing to both of its high carrier concentration and large band gap, ZnO:Al (ZAO) films which is an n-type degenerate semiconductor, exhibits low resistance and high transmittance in the visible range. This work studies the crystal structure, optical and electrical properties and preparation methods of ZAO films, and discusses the existing problems and application prospective of ZAO films.
基金Project(50801017)supported by the National Natural Science Foundation of ChinaProject(20080440843)supported by China Postdoctoral Science FoundationProject(HIT.NSRIF.2009028)supported by Natural Scientific Research Innovation Foundation in Harbin Institute of Technology,China
文摘Tensile tests with small deformation amounts of 0.5%,1%,3%and 5%were performed at room temperature on as cast Mg-1%Al alloy.Microstructures of the Mg-1%Al alloys before and after deformation were observed by optical microscopy(OM) and transmission electron microscopy(TEM).The strain amplitude dependent and temperature dependent damping capacities of the as-cast and deformed Mg-1%Al alloys were investigated by dynamic mechanical analysis(DMA).The mechanism of deformation on damping capacity of Mg-1%Al alloy was discussed.The results show that the as-cast Mg-1%Al alloy has high damping value at high strain.When the tensile elongation is higher than 3%,the damping values of this alloy in high strain region are significantly decreased at room temperature.But the large amount of dislocations produced by tensile deformation are activated by heat,and then increase the damping value at high temperature.
基金Supported by the National Natural Science Foundation of China(21206076) the Natural Science Foundation of Jiangsu Province(BK2012401 and BK2011715) National High Technology Research and Development Program of China(2011AA050701)
文摘In this work,we describe a novel facile method to prepare long one-dimensional hybrid nanofibers by using hydrated bacterial cellulose nanofibers(BCF)as a template.Silver(Ag)nanoparticles with an average diameter of 1.5 nm were well dispersed on BCF via a simple in situ chemical-reduction between AgNO3and NaBH4at a relatively low temperature.A growth mechanism is proposed that Ag nanoparticles are uniformly anchored onto BCF by coordination with BC-containing hydroxyl groups.The bare BCF and as-prepared Ag/BCF hybrid nanofibers were characterized by several techniques including transmission electron microscopy,X-ray diffraction,thermogravimetric analyses,and ultraviolet-visible(UV-Vis)absorption spectra.The antibacterial properties of Ag/BCF hybrid nanofibers against Escherichia coli(E.coli,Gram-negative)and Staphylococcu saureus(S.saureus,Gram-positive)bacteria were evaluated by using modified Kirby Bauer method and colony forming count method.The results show that Ag nanoparticles are well dispersed on BCF surface via in situ chemical-reduction.The Ag/BCF hybrid nanofiber presents strong antibacterial property and thus offers its candidature for use as functional antimicrobial agents.
基金Project(Y4110230)supported by Natural Science Foundation of Zhejiang Province,ChinaProject(51204146,51101140)supported by the National Natural Science Foundation of ChinaProject(2012M521197)supported by Postdoctoral Science Foundation of China
文摘A simple strategy to prepare a hybrid of nanocomposites of anatase TiO2/graphene nanosheets (GNS) as anode materials for lithium-ion batteries was reported.The morphology and crystal structure were studied by X-ray diffraction (XRD),field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM).The electrochemical performance was evaluated by galvanostatic charge-lischarge tests and alternating current (AC) impedance spectroscopy.The results show that the TiO2/GNS electrode exhibit higher electrochemical performance than that of TiO2 electrode regardless of the rate.Even at 500 mA/g,the capacity of TiO2/GNS is 120.3 mAh/g,which is higher than that of TiO2 61.6 mAh/g.The high performance is attributed to the addition of graphene to improve electrical conductivity and reduce polarization.
基金Projects(50871050, 50961009) supported by the National Natural Science Foundation of ChinaProject(2010ZD05) supported by the Natural Science Foundation of Inner Mongolia, ChinaProject(NJzy08071) supported by the Higher Education Science Research Project of Inner Mongolia, China
文摘In order to improve the electrochemical hydrogen storage performance of the Mg2Ni-type electrode alloys, Mg in the alloy was partially substituted by La, and the nanocrystalline and amorphous Mg2Ni-type Mg20-xLaxNi10 (x-=0, 2) alloys were synthesized by melt-spinning technique. The microstructures of the as-spun alloys were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The electrochemical hydrogen storage properties of the experimental alloys were tested. The results show that no amorphous phase is detected in the as-spun Mg20Ni10 alloy, but the as-spun Mg18La2Ni10 alloy holds a major amorphous phase. As La content increases from 0 to 2, the maximum discharge capacity of the as-spun (20 m/s) alloys rises from 96.5 to 387.1 mA.h/g, and the capacity retaining rate (S20) at the 20th cycle grows from 31.3% to 71.7%. Melt-spinning engenders an impactful effect on the electrochemical hydrogen storage performances of the alloys. With the increase in the spinning rate from 0 to 30 m/s, the maximum discharge capacity increases from 30.3 to 135.5 mA.h/g for the Mg20Ni10 alloy, and from 197.2 to 406.5 mA-h/g for the Mg18La2Ni10 alloy. The capacity retaining rate (S20) of the Mg2oNi10 alloy at the 20th cycle slightly falls from 36.7% to 27.1%, but it markedly mounts up from 37.3% to 78.3% for the Mg18La2Ni10 alloy.
文摘As a preliminary investigation towards obtaining carbon nanotube composite adsorbent for CO2 capture, in this study CO2 adsorption performance of three commercial carbon nanotubes (CNTs) one single-walled carbon nanotubes (SWCNTs), and two (2) different multi-walled carbon nanotubes (referred to as A-MWCNTs and B-MWCNTs) were evaluated and compared. The purpose of this study was to compare the different types of CNTs and select the best to serve as the solid anchor in the development of a hydrophobic composite adsorbent material for CO2 capture. The N2 physi- sorption of the CNTs was conducted to determine their surface area, pore volume and pore size. In addition, morphology and purity of the CNTs were checked with Transmission Electron Microscopy and Raman Spectroscopy, respectively. The CO2 adsorption capacity of the CNTs was evaluated using Thermo-gravimetric analysis (TGA) at 1.1 bar, at operating temperature ranged from 25 to 55 ~C and at different CO2 feed flow rates, in order to evaluate the effects of these variables on the CO2 adsorption capacity. The results of CO2 adsorption with the TGA show that CO2 adsorption capacity for both SWCNTs and MWCNTs was the highest at 25 ~C. Changing the CO2 flowrates had no significant effect on the adsorption capacity of MWCNTs, but decreasing the CO2 flow rate resulted in the enhancement of the CO2 adsorption capacity of SWCNTs. Overall, it was found that the SWCNTs displayed the highest CO2 adsorption capacity (29.97 gCO2/kg ad- sorbent) when compared to the MWCNTs (12.09 gCO2/kg adsorbent), indicating a 150% increase in adsorption capacity over MWCNTs.
文摘Analytical solutions for a Griffith crack inside an infinite piezoel ectromagnetic medium under combined mechanical-electrical-magnetic loadings are formulated using integral transform method. The singular stress, electric and magnetic fields in the piez oelectromagnetic material are obtained by the theory of linear piezoelectromagneticity. Fourier transforms are used to reduce the mixed boundary value problems of the crack, which is assumed to b e permeable, to dual integral equations. The solution of the dual integral equations is then ex pressed analytically. Expressions for strains, stresses, electric fields, electric displacements, mag netic fields and magnetic inductions in the vicinity of the crack tip are derived. Field intensi ty factors and energy release rate for piezoelectromagnetic material are obtaine d. The stresses, electric displacements and magnetic inductions at the crack tip show the traditional square root singu larities; and the electric field intensity factor (EFIF) and the magnetic field intensity factor (MFIF) are always zero.
基金Project(2005CB623700) supported by the National Basic Research Program of China
文摘The effects of Yb content on the microstructures and mechanical properties of 2519A aluminum alloy plate were investigated by means of tensile test,optical microscopy,transmission electron microscopy,scanning electron microscopy and X-ray diffractometer.The results show that addition of 0.17% (mass fraction) Yb increases the density of θ' particles of the 2519A alloy plate and reduces the coarsening speed rate of θ' phase at 300 ℃.Therefore,tensile strength is enhanced from 483.2 MPa to 501.0 MPa at room temperature and is improved from 139.5 MPa to 169.4 MPa at 300 ℃.The results also show that with the addition of 0.30% (mass fraction) Yb,the mechanical properties increase at 300 ℃ and decrease at room temperature.With Yb additions,the Al7.4Cu9.6Yb2 phase is found whilst the segregated phases of as-cast alloys along grain boundaries become discontinuous,thin and spheroidized.
文摘This paper relates to highly dispersed supported Pd/MWCNTs and Fd/a-Al2O3 catalysts prepared by biological reduction method. The physico-chemical properties and the difference in catalytic activity of Pd catalysts prepared by bio- logical reduction method and chemical method, respectively, were investigated using XRD, TEM and specific surface char- acterization methods. The catalytic properties of catalysts were studied through activity evaluation means. The test results showed that the catalysts prepared by biological method were characteristic of small Pd nanoparticle size, good dispersion and low agglomeration, while possessing a high activity and stability in styrene hydrogenation reaction in comparison with catalysts prelgared via the chemical method.
基金Project(2012CB619500) supported by the National Basic Research Program of ChinaProject(201012200238) supported from the Freedom Explore Program of Central South University, China
文摘The influence of exfoliation corrosion on the tensile properties of a high strength Al-Zn-Mg-Cu alloy was investigated by ambient temperature tensile testing, optical microscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). After exfoliation corrosion immersion, blisters and corrosion pits can be seen on the sheet surface, which lead to loss of materials and notches. A number of intergranular cracks are observed to initiate at the bottom of the corrosion-induced notches and propagate rapidly into the bulk materials during tensile. Consequently, exfoliation corrosion results in significant loss of strength and brittle fracture. EBSD results show that the crack propagation path is primarily along the grain boundaries with misorientation of-45°, and coincidence site lattice (CSL) boundaries are slightly more resistant to crack.
基金Supported by the National Natural Science Foundation of China(21276054,21376280)
文摘Large surface areas nano-scale zirconia was prepared by the self-assembly route and was employed as support in nickel catalysts for the CO selective methanation. The effects of Ni loading and the catalyst calcination temperature on the performance of the catalyst for CO selective methanation reaction were investigated. The cata- lysts were characterized by Brunauer-Emmett-Teller (BET), transmission electron microscope (TEM), X-ray dif- fraction (XRD) and temperature-programmed reduction (TPR). The results showed that the as-synthesized Ni/nano-ZrO2 catalysts presented high activity for CO methanation due to the interaction between Ni active particle and nano zir- conia support. The selectivity for the CO methanation influenced significantly by the particle size of the active Ni species. The exorbitant calcination resulted in the conglomeration of dispersive Ni particles and led to the decrease of CO methanation selectivity. Among the catalysts studied, the 7.5% (by mass) Ni/ZrO2 catalyst calcinated at 500℃ was the most effective for the CO selective methanation. It can preferentially catalyze the CO methanation with a higher 99% conversion in the CO/CO2 competitive methanation system over the temperature range of 260-280℃, while keeping the CO2 conversion relatively low.
文摘The effect of Zn addition on the microstructure, tensile properties and electrochemical properties of as-annealed 3003 Al alloy was investigated through TEM observations, tensile tests and Tafel polarization analysis. High density precipitates are observed in the Zn-containing alloys and the alloy with 1.8% Zn addition also has rod-like precipitates. Tensile test results indicate that Zn has a great effect on tensile strength of 3003 Al alloy. The alloy with 1.5% Zn addition has the highest ultimate tensile strength. The electrochemical results indicate that Zn addition to 3003 Al alloy also has great impact on the corrosion potential of the 3003 A1 alloy in 0.5% NaCl solution and ethylene glycol-water solution. The corrosion potential varies with the Zn content and shifts negatively.
基金Project(51272289) supported by the National Natural Science Foundation of China
文摘The main goal of this work is to explore the possibility of using Au-modified hydroxyapatite(HA) as a potential sensor material. Tube-like HA structure was fabricated with the aid of a Nafion N-117 cation exchange membrane and gold(Au) nanoparticles were added by a hydrothermal method. The morphology, structure and composition were characterized by scanning electron microscopy(SEM), transmission electron microscopy(TEM), X-ray diffraction(XRD), and X-ray photoelectron spectroscopy(XPS). The gas sensing properties were also investigated. Results show that Au nanoparticles are dispersed into the HA powder, which is tube-like, with rough inner and outer surfaces. Compared with pure HA, Au-modified HA exhibits improved sensing properties for NH_3. 5%(mass fraction) Au-modified HA shows the highest response with relatively short response/recovery time. The response is up to 79.2% when the corresponding sensor is exposed to 200×10^(-6) NH_3 at room temperature, and the response time and recovery time are 20 s and 25 s, respectively. For lower concentration, like 50×10^(-6), the response is still up to 70.8%. Good selectivity and repeatability are also observed. The sensing mechanism of high response and selectivity for NH_3 gas was also discussed. These results suggest that Au-HA composite is a promising material for NH_3 sensors operating at room temperature.
文摘This article mainly discussed bulk material lHvl^ared by powder metallurgy, and the commercial 2024 aluminum alloy powder and FeNiCrCoA13 high entropy alloy powder (both produced by argon gas atomization process) were ball-milled for different hours. The prepared powder was consolidated by hot extrusion method. The microstruetures of the milled powder and bulk alloy were examined by X - Ray Diffraction (XRD), Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM). The thermal stability was tested by differential scanning calorimetry (DSC). Mechanical properties of the extruded alloy were examined by Vickers hardness tester and mechanical testing machine. The results show that after milling, the mixed particle sizes and microstructures of the alloy powder change obviously. The compressive strength of the extruded alloy has reached 580 MPa under certain conditions of milling time and composition.
基金Project(2005CB623706) supported by the National Basic Research Program of China
文摘The microstructures and mechanical properties of Al-6Zn-2Mg-1.5Cu-0.4Er alloy under different treatment conditions were investigated by transmission electron microscopy (TEM) observation, and tensile properties and hardness test, respectively. The relationship between mechanical properties and microstructures of the alloys was discussed. With trace Er addition to A1-Zn-Mg-Cu alloy, Er and Al interact to form Al3Er phase, which is coherent with a(A1) matrix. The results show that Al-Zn-Mg-Cu alloy after retrogression and re-ageing (RRA) heat treatment exhibits higher tensile strength, ductility and conductivity.
文摘Transmission electron microscopy and surface- and bulk-sensitive spectroscopic methods were used to study the morphology and the electronic structure of a hybrid organic-inorganic system composed of gold nanoparticles (NP's) which were distributed in an organic matrix. Au atoms deposited onto a copper phthalocyanine (CuPc) surface diffuse into the organic matrix and self-assemble in well defined NP's with metallic properties. No formation of a continuous metallic Au film on top of the CuPc film is observed up to nominal coverages as large as 130 A.
文摘In order to develop an excellent pseudocapacitor with both high specific capacitance and outstanding stretchability to match with other devices applicable in future wearable and bio-implantable systems, we focus our studies on three vital aspects: Stretchability of hybrid film electrodes, the interface between different components, and the integrated performance in stretchability and electrochemistry of supercapacitors based on single-walled carbon nanotube/ polyaniline (SWCNT/PANI) composite films on pre-elongated elastomers. Owing to the moderate porosity, the buckled hybrid film avoids the cracking which occurs in conventional stretchable hybrid electrodes, and both a high specific capacitance of 435 F.g-1 and a high strain tolerance of 140% have been achieved. The good SWCNT/PANI interfacial coupling and the reinforced solid electrolyte penetration structure enable the integrated pseudocapacitors to have stretch- resistant interfaces between different units and maintain a high performance under a stretching of 120% elongation, even after 1,000 cyclic elongations.