The ultrasonic motor is a sort of new type of micromotor with special structure. By use of piezoelectric converse effect of ceramics, the electrical energy is transformed into mechanical energy. Its operating principl...The ultrasonic motor is a sort of new type of micromotor with special structure. By use of piezoelectric converse effect of ceramics, the electrical energy is transformed into mechanical energy. Its operating principle is quite different from that of the traditional motors. In this paper the equivalent circuits of the ring stator and even the whole motor are proposed after studying the equivalent circuit of piezoelectric vibrator. Then the paper makes detailed analyses of each part of the control system, which has been simplified by the equivalent circuit. The theory in this paper has been proved through experiments.展开更多
A vehicle stopping method using an electric brake until a traction motor is stopped is studied. At the moment of vehicle stop, electric brake is changed to control mode where torque is reduced at a low speed. Gradient...A vehicle stopping method using an electric brake until a traction motor is stopped is studied. At the moment of vehicle stop, electric brake is changed to control mode where torque is reduced at a low speed. Gradient is controlled by estimating the load torque of motor, thereby traction motor is not rotated after stop. In addition, coasting operation and brake test are performed from normal-opposite operation and start using a small-scale model comprising the inertial load equipment and the power converter. Further, traction motor is made to be equipped with a suspension torque. Pure electric braking that makes traction motor stop by an air brake at the time of stop is also implemented. Constant torque range and constant power range are expanded during braking so that braking force is secured with the electric brakes even in high speed region. Therefore, vehicle reduction effect can be expected by reducing parts related with an air brake which is not used frequently by using a pure electric brake in the M car in wide speed region. Further, maintenance of brake system can be reduced. Besides, ride comfort of passenger in the electric rail car, energy efficiency improvement, and noise reduction effect can be additionally expected. Further, an improved brake method that uses only an electric brake till motor stop is proposed by comparing those in the blending brake that uses an air brake while reducing brake torque at vehicle stop.展开更多
A three degree-of-freedom (DOF) ultrasonic motor (USM) with a cylinder-shaped stator and a spherical rotor is introduced, which uses one first order longitudinal and two second order bending nature vibration modes of ...A three degree-of-freedom (DOF) ultrasonic motor (USM) with a cylinder-shaped stator and a spherical rotor is introduced, which uses one first order longitudinal and two second order bending nature vibration modes of the cylinder. Control strategies for the two DOF trajectory following are studied and applied to the prototype USM. Vibration amplitude control is employed for speed regulation. The first trajectory following strategy is a step-by-step interpolation. The second strategy is vector decomposition control. Three pulse width modulation (PWM) methods for the exciting voltage regulation are investigated. These methods are compared and verified by several experiments. The key is to keep the phase differences of the three vibration constants and small exciting voltage distortion while the exciting voltages are changed for simplifing the control process and obtaining good control performance. The vector control method has advantages of small trajectory following error, smooth moving and low noise.展开更多
In paper it introduced a review of modem traction vehicle drive system with induction motor drive system （PMSM with single or dual rotor drive system） or BLDC motor with different configuration of magnetic circuits....In paper it introduced a review of modem traction vehicle drive system with induction motor drive system （PMSM with single or dual rotor drive system） or BLDC motor with different configuration of magnetic circuits. For particular part of drive system proposed a quasi intelligent control system version smart control enables multi criteria predictive control of vehicle work. In the paper presented also a selected diagnostic procedure, enables monitoring exploitation parameters, and prediction of probable failure state. For different vehicle work state realized a simulation models and crash test of exploitations failure models.展开更多
A brain-computer interface(BCI)-based electric wheelchair control system was developed, which enables the users to move the wheelchair forward or backward, and turn left or right without any pre-learning. This control...A brain-computer interface(BCI)-based electric wheelchair control system was developed, which enables the users to move the wheelchair forward or backward, and turn left or right without any pre-learning. This control system makes use of the amplitude enhancement of alpha-wave blocking in electroencephalogram(EEG) when eyes close for more than 1 s to constitute a BCI for the switch control of wheelchair movements. The system was formed by BCI control panel, data acquisition, signal processing unit and interface control circuit. Eight volunteers participated in the wheelchair control experiments according to the preset routes. The experimental results show that the mean success control rate of all the subjects was 81.3%, with the highest reaching 93.7%. When one subject's triggering time was 2.8 s, i.e., the flashing time of each cycle light was 2.8 s, the average information transfer rate was 8.10 bit/min, with the highest reaching 12.54 bit/min.展开更多
Analysis and measurements of the vibration on AM50 horizontal axis roadheader of electric-control-box was carried out, and the vibration characteristics were obtained. Based on the results, a new type of wire rope iso...Analysis and measurements of the vibration on AM50 horizontal axis roadheader of electric-control-box was carried out, and the vibration characteristics were obtained. Based on the results, a new type of wire rope isolator was designed, whose characteristics were examined by experiments. The tests show that the wire rope isolator achieves satisfied results and can meet the requirements for the vibration control of the roadheader of electric-control-box.展开更多
Analyzed working principle and starting process of asynchronous motor direct torque control system. In order to solve the problem of serious fluctuation of starting current in traditional control scheme, the author pu...Analyzed working principle and starting process of asynchronous motor direct torque control system. In order to solve the problem of serious fluctuation of starting current in traditional control scheme, the author puts forward a new kind of starting method which can limit voltage value to achieve the goal of reducing fluctuation of the current by increasing zero voltage vectors during the stage of starting. The author has also carried on simulation study on the system, and the result of simulation study shows that this method is effectual.展开更多
The article is designed hardware platform of TMS320F2812 primary control chip based on the motor drive controller outputs and input signal, the use of DSP technology, together with the corresponding peripheral driver ...The article is designed hardware platform of TMS320F2812 primary control chip based on the motor drive controller outputs and input signal, the use of DSP technology, together with the corresponding peripheral driver circuit, a signal processing circuit and other processing module, the design and realize a piece of printed circuit board to achieve the required functionality. Systems software modules is implement hardware configuration and achieve control strategies in the DSP CCS compiler environment and using C and assembly language. Through CAN controller that comes with the DSP programming, achieved its CAN signal transmission and reception.展开更多
This paper presents the design and implementation of the embedded microcontrollers within a telescope control system. The design objectives of the overall system are to automatically find light emitting objects at nig...This paper presents the design and implementation of the embedded microcontrollers within a telescope control system. The design objectives of the overall system are to automatically find light emitting objects at night within a user specified area, to track a light emitting object for a user specified time given the initial position of the object, and to allow the user access to these functions through a graphical user interface. The embedded system is used to provide a communication link between the graphical user interface and system hardware, to provide angle data processing for a dual axis accelerometer, to provide data processing for an electronic compass, and to provide pulse outputs for the step and direction inputs of three stepper motor drives. This paper will describe the design, implementation, and results of each of these objectives.展开更多
Induction motor is used in many applications to drive an electromechanical system. Transients of the motor torque and speed are outlined by the inertia of rotating rotor. The paper deals with influence of rotor inerti...Induction motor is used in many applications to drive an electromechanical system. Transients of the motor torque and speed are outlined by the inertia of rotating rotor. The paper deals with influence of rotor inertia to transients of motor speed. The method of speed control measurement and experimental equipment is discussed. Simulation and experimental results are compared.展开更多
This paper presents a sliding mode observer for sensorless operation of SRM （switched reluctance motor） drive. Design of such an observer depends mainly on the nonlinear model of SRM. In this technique, neither extr...This paper presents a sliding mode observer for sensorless operation of SRM （switched reluctance motor） drive. Design of such an observer depends mainly on the nonlinear model of SRM. In this technique, neither extra hardware nor huge memory space are not required but it only requires active phase measurements. Furthermore, PI （proportional integral） and adaptive FLPI （fuzzy logic PI） controllers are suggested to operate individually along with the SMO （sliding mode observer） to cover a full speed range of sensorless controller. Both controller schemes operate in PWM （pulse width modulation） control mode. The proposed observer is implemented and tested using a digital signal processor. All results obtained with both simulation and experimental investigations corroborate the superior performance of the adaptive fuzzy logic controller （FLPI） when compared with those of PI controller.展开更多
文摘The ultrasonic motor is a sort of new type of micromotor with special structure. By use of piezoelectric converse effect of ceramics, the electrical energy is transformed into mechanical energy. Its operating principle is quite different from that of the traditional motors. In this paper the equivalent circuits of the ring stator and even the whole motor are proposed after studying the equivalent circuit of piezoelectric vibrator. Then the paper makes detailed analyses of each part of the control system, which has been simplified by the equivalent circuit. The theory in this paper has been proved through experiments.
文摘A vehicle stopping method using an electric brake until a traction motor is stopped is studied. At the moment of vehicle stop, electric brake is changed to control mode where torque is reduced at a low speed. Gradient is controlled by estimating the load torque of motor, thereby traction motor is not rotated after stop. In addition, coasting operation and brake test are performed from normal-opposite operation and start using a small-scale model comprising the inertial load equipment and the power converter. Further, traction motor is made to be equipped with a suspension torque. Pure electric braking that makes traction motor stop by an air brake at the time of stop is also implemented. Constant torque range and constant power range are expanded during braking so that braking force is secured with the electric brakes even in high speed region. Therefore, vehicle reduction effect can be expected by reducing parts related with an air brake which is not used frequently by using a pure electric brake in the M car in wide speed region. Further, maintenance of brake system can be reduced. Besides, ride comfort of passenger in the electric rail car, energy efficiency improvement, and noise reduction effect can be additionally expected. Further, an improved brake method that uses only an electric brake till motor stop is proposed by comparing those in the blending brake that uses an air brake while reducing brake torque at vehicle stop.
文摘A three degree-of-freedom (DOF) ultrasonic motor (USM) with a cylinder-shaped stator and a spherical rotor is introduced, which uses one first order longitudinal and two second order bending nature vibration modes of the cylinder. Control strategies for the two DOF trajectory following are studied and applied to the prototype USM. Vibration amplitude control is employed for speed regulation. The first trajectory following strategy is a step-by-step interpolation. The second strategy is vector decomposition control. Three pulse width modulation (PWM) methods for the exciting voltage regulation are investigated. These methods are compared and verified by several experiments. The key is to keep the phase differences of the three vibration constants and small exciting voltage distortion while the exciting voltages are changed for simplifing the control process and obtaining good control performance. The vector control method has advantages of small trajectory following error, smooth moving and low noise.
文摘In paper it introduced a review of modem traction vehicle drive system with induction motor drive system （PMSM with single or dual rotor drive system） or BLDC motor with different configuration of magnetic circuits. For particular part of drive system proposed a quasi intelligent control system version smart control enables multi criteria predictive control of vehicle work. In the paper presented also a selected diagnostic procedure, enables monitoring exploitation parameters, and prediction of probable failure state. For different vehicle work state realized a simulation models and crash test of exploitations failure models.
基金Supported by the National Natural Science Foundation of China(No.81222021,No.30970875,No.90920015,No.61172008 and No.81171423)National Key Technology Research and Development Program of the Ministry of Science and Technology of China(No.2012BAI34B02)Program for New Century Excellent Talents in University of the Ministry of Education of China(No.NCET-10-0618)
文摘A brain-computer interface(BCI)-based electric wheelchair control system was developed, which enables the users to move the wheelchair forward or backward, and turn left or right without any pre-learning. This control system makes use of the amplitude enhancement of alpha-wave blocking in electroencephalogram(EEG) when eyes close for more than 1 s to constitute a BCI for the switch control of wheelchair movements. The system was formed by BCI control panel, data acquisition, signal processing unit and interface control circuit. Eight volunteers participated in the wheelchair control experiments according to the preset routes. The experimental results show that the mean success control rate of all the subjects was 81.3%, with the highest reaching 93.7%. When one subject's triggering time was 2.8 s, i.e., the flashing time of each cycle light was 2.8 s, the average information transfer rate was 8.10 bit/min, with the highest reaching 12.54 bit/min.
基金State Key Project of Science and Technology of The Eighth Five-Year Plan(85-201-01-01-3)
文摘Analysis and measurements of the vibration on AM50 horizontal axis roadheader of electric-control-box was carried out, and the vibration characteristics were obtained. Based on the results, a new type of wire rope isolator was designed, whose characteristics were examined by experiments. The tests show that the wire rope isolator achieves satisfied results and can meet the requirements for the vibration control of the roadheader of electric-control-box.
文摘Analyzed working principle and starting process of asynchronous motor direct torque control system. In order to solve the problem of serious fluctuation of starting current in traditional control scheme, the author puts forward a new kind of starting method which can limit voltage value to achieve the goal of reducing fluctuation of the current by increasing zero voltage vectors during the stage of starting. The author has also carried on simulation study on the system, and the result of simulation study shows that this method is effectual.
文摘The article is designed hardware platform of TMS320F2812 primary control chip based on the motor drive controller outputs and input signal, the use of DSP technology, together with the corresponding peripheral driver circuit, a signal processing circuit and other processing module, the design and realize a piece of printed circuit board to achieve the required functionality. Systems software modules is implement hardware configuration and achieve control strategies in the DSP CCS compiler environment and using C and assembly language. Through CAN controller that comes with the DSP programming, achieved its CAN signal transmission and reception.
文摘This paper presents the design and implementation of the embedded microcontrollers within a telescope control system. The design objectives of the overall system are to automatically find light emitting objects at night within a user specified area, to track a light emitting object for a user specified time given the initial position of the object, and to allow the user access to these functions through a graphical user interface. The embedded system is used to provide a communication link between the graphical user interface and system hardware, to provide angle data processing for a dual axis accelerometer, to provide data processing for an electronic compass, and to provide pulse outputs for the step and direction inputs of three stepper motor drives. This paper will describe the design, implementation, and results of each of these objectives.
文摘Induction motor is used in many applications to drive an electromechanical system. Transients of the motor torque and speed are outlined by the inertia of rotating rotor. The paper deals with influence of rotor inertia to transients of motor speed. The method of speed control measurement and experimental equipment is discussed. Simulation and experimental results are compared.
文摘This paper presents a sliding mode observer for sensorless operation of SRM （switched reluctance motor） drive. Design of such an observer depends mainly on the nonlinear model of SRM. In this technique, neither extra hardware nor huge memory space are not required but it only requires active phase measurements. Furthermore, PI （proportional integral） and adaptive FLPI （fuzzy logic PI） controllers are suggested to operate individually along with the SMO （sliding mode observer） to cover a full speed range of sensorless controller. Both controller schemes operate in PWM （pulse width modulation） control mode. The proposed observer is implemented and tested using a digital signal processor. All results obtained with both simulation and experimental investigations corroborate the superior performance of the adaptive fuzzy logic controller （FLPI） when compared with those of PI controller.
