电热双金属复合管热传导的数值分析

导出变物性下电热复合管热传导的离散近似方程式，源项采用切线方案予以局部线性化．结合一个典型实例计算，指出此类实验件的固有热特点，以及外壁温、总电流、内径测量偏差与内壁温、电功率计算值之间的数值联系．对比解析解和传热实验数据，表明数值分析是可靠有效的．本文为这一构思新颖的电传热实验件工作参数和结构尺寸的设定提供了方法和依据．

Heat transfer model for microwave hot in-place recycling of asphalt pavements

In order to solve for temperature fields in microwave heating for recycling asphalt mixtures, a two-dimensional heat transfer model for the asphalt mixtures within the heating range is built based on the theory of unsteady heat conduction. Four onedimensional heat transfer models are established for the asphalt mixtures outside the heating range, which are simplified into four half-infinite solids. The intensity of the radiation electric field is calculated through experiment by using heating water loads. It is suggested that the mathematical model of boundary conditions can be established in two ways, which are theoretical deduction and experimental reverse. The actual temperature field is achieved by fitting temperatures of different positions collected in the heating experiment. The simulant temperature field, which is solved with the Matlab PDE toolbox, is in good agreement with the actual temperature field. The results indicate that the proposed models have high precision and can be directly used to calculate the temperature distribution of asphalt pavements.

让学生唱主角

自然教学的目的是:指导学生获得自然科学的基础知识和基本技能,培养和发展学生的能力。为实现这一目的,近几年在自然教学工作中我们做了初步尝试,并取得了良好效果。我们的做法是:让学生唱主角,从动手动脑中获得知识发展能力。

Experimental study on heat generation and dissipation performance of PEV Lithium-ion battery

Based on the lithium-ion battery pure electric vehicle （PEV） application, two capacity types of batteries are applied in thermal characteristic experiments. With the experimental comparison method, battery thermal characteristics and heat generation mechanism are studied. Experiments of batteries in cases of different dimensions, batteries with different air cooling velocity and two capacity types of batteries in free convection environment are put forward. Battery heat generation performance, heat dissipation performance and comparison of different capacity types＇ batteries are researched and summarized. Conclusions of battery heat generation and dissipation in PEV applications, important battery thermal management factors and suggestions are put forward.

Experimental study on thermal characteristics of LiFePO_4 power batteries

As an important high-energy chemical power source, lithium-ion power batteries come up to application problems of thermal performance, such as extended temperature range and high power charge ＆ discharge. LiFeP04 battery is applied and developed well recently, its charge and discharge experiment at different temperatures and hybrid pulse power characterization （HPPC） test are analyzed, and the optimal temperature range of LiFeP04 battery is put forward. In order to provide experimental suggestion of power battery application and its thermal management, internal resistance, influencing factor of electromotive force and entropy change state of charge （SOC）, battery thermal characteristic of different charge ＆ discharge rates are summarized.

Excess Heat Power Registration in High Voltage Electrolysis Cell Experiments

Experimental research of the heat and high-energy processes occurring in the cathode solid medium in the high voltage electric discharge system （electrolysis cell and glow discharge device） is presented. The experiments were carried out： Electrolysis in heavy water with a Pd cathode, electrolysis in light water with Ni and Pd cathodes, the glow discharge in deuterium with a Pd cathode. Excess heat was observed in experiments with high-voltage electrolysis （1,000 V or more）. The experiments showed that the maximum excess heat power values of 5-8 W for glow discharge and 180-280 W for high-voltage electrolysis and heat efficiency up to 170% for glow discharge, and 800% for high-voltage electrolysis. The production of impurity nuclide yield showing a shift of up to a few per cent from natural isotopic abundances was detected by spark mass spectrometry and by secondary ionic mass spectrometry. The authors propose based on these experimental results a phenomenological model for low energy nuclear reaction.

Microstructure evolution of 7050 aluminum alloy during hot deformation

Hot compression of 7050 aluminum alloy was performed on Gleeble 1500D thermo-mechanical simulator at 350 ℃ and 450 ℃ with a constant strain rate of 0.1 s-1 to different nominal strains of 0.1, 0.3 and 0.7. Microstructures of 7050 alloy under various compression conditions were observed by TEM to investigate the microstructure evolution process of the alloy deformed at various temperatures. The microstructure evolves from dislocation tangles to cell structure and subgrain structure when being deformed at 350 ℃, of which dynamic recovery is the softening mechanism. However, continuous dynamic recrystallization (DRX) occurs during hot deformation at 450 ℃, in which the main nucleation mechanisms of DRX are subgrain growth and subgrain coalescence rather than particle-simulated nucleation (PSN).

Effects of precipitation strengthening heat treatment for Al-Mg alloy

The corrosions resulting from defects in painting layers frequently occur in Al alloys, so the application of corrosion preventing systems is also very important. Optimum conditions in terms of electrochemistry in relation to solution treatment, quenching and artificial aging treatment were established in order to optimize precipitation strengthening conditions intended to enhance the strength of Al alloys. Slow strain rate tests （SSRT） at various applied potentials were conducted in potential range from -1.8 to 0.5 V. The results show that the maximum tensile strengths, elongations and time-to-fracture are shown to be high values. After precipitation strengthening heat treatment, a tendency appear that time-to-fracture increases as elongation increases. In the potential range from -1.3 V to -0.7 V, the specimens show excellent mechanical properties, and thus this range is considered to be a corrosion prevention range.

Excess Heat Power Registration in Experiments with High Voltage Electric Discharge Systems

The author review results on LENR （low-energy nuclear reaction） processes in the cathodes of a high current glow discharge and a HVEC （high-voltage electrolysis cell）. The cathodes used in the experiments were made of Ni foil, Pd foil, Pd coated Re and solid-state nanostructured Pd. Up to 300 W of excess heat power, with a power gain up to 340%, was observed in experiments using a high-voltage electrolysis cell. Based on these experimental results, we propose a phenomenological model for LENR.

Ammonia corrosion analysis of copper tubes and experimental research on non-copper improvement for heat exchanger in power plant

Ammonia corrosion in copper tube will affect the safety of boiler running in power plant. Therefore, no copper in heating system has become a technical orientation in heat exchanger reconstruction, This paper analyzes the condition and mechanism of ammonia corrosion occurring in copper tube used in coal-fired power plants. Using a general steam condensation testing equipment only for horizontal single tube, with water vapor and water as working fluid, on two types of steel tube with 2-side enhancement heat transfer, namely, a spirally fluted tube and a ratchet tube with internal spiral groove （RISG tube） which was developed recently, a set of experimental tests are conducted to investigate the characteristics of heat transfer and hydromeehanics. In order to compare easily, both one copper smooth tube and one steel smooth tube are also used in the experiment. The experimental results, which get from single horizontal tube, show that the overall heat transfer coefficient of steel spirally fluted tube are improved by 10%o to 17%, and that of the steel RISG tube（22%-28%） is better than steel spirally fluted tube, its flow resistance coefficient is only increased by 22% to 66% when compared with smooth tube. Based on a lot of experimental data, the steel spirally fluted tube and the steel RISG tube were applied in a low pressure preheater and an oil-cooler of some or other power plant respectively. The field testing results showed that their heat transfer coefficient with each types of enhancement heat transfer tubes were improved by 2.5% and 21%-45% comparing with copper smooth tube heat exchangers. Both basic and field experiment indicates that the steel tube with 2-side enhancement heat transfer is an ideal choice for heat exchanger reconstruction in no copper issue in power plants.

Hydrogen Concentration of Co-Deposited Carbon Films Produced in the Vicinity of Local Island Divertor in LHD

In international thermonuclear experimental reactor （ITER）, one of major concerns is an in-vessel tritium inventory from a point of safety. It is believed that the carbon-tritium co-deposited film produced by the erosion of carbon diverter walls has a high tritium concentration. However, no systematic evaluation for the tritium concentration has been conducted yet. In the present study, the carbon-hydrogen co-deposited films were prepared at the wall of pumping duct in Local Island Divertor experiments of LHD, in order to evaluate the tritium concentration of the co-deposited films produced in ITER. The hydrogen concentration was obtained by measuring the amount of retained hydrogen in the film and the mass density of the film. The hydrogen concentration of the co-deposited carbon film at the wall not facing to the plasma with a low temperature was extremely high, 1.3 in the atomic ratio of H/C. This value is triple times higher than the previous value obtained so far. The crystal structure of the co-deposited carbon film observed by Raman spectroscopy showed very unique structure （polymeric aC：H）, which is well consistent with the high hydrogen concentration. The present study suggests that the tritium concentration of the co-deposited film in ITER depends on the wall position and becomes quite high as high as T/C-0.65. The results obtained contribute to evaluate the in-vessel tritium inventory owing to the co-deposited carbon films.

The Effects of Voltage and Suction Line Heat Exchanger on a Domestic Refrigerator＇s Performance

This experimental analysis shows the measured reduction in energy consumption as well as the effects of voltage on cycle temperatures, pressures, flow rates and also compressor speed （revolutions per minute）. The domestic refrigerator used R134a as refrigerant. Two energy consumption procedures were adapted from the JIS and ISO standards. The biggest difference between two standards is that the fridge is not opened in the ISO test while it is opened a number of times in the JIS test. The tests were carried out between 190 V and 250 V in steps of 10 V. The reduction in energy consumption was of 49.78 W-h per day or 6.27% of the total consumption. The experiments also showed that the voltage drop resulted in only a small rpm drop which in turn did not result in a noticeable refrigerant flow-rate change. Consequently the temperatures and pressures were not affected.

Modeling, Experimental Study on the Heat Transfer Characteristics of Thermoelectric Generator

This paper investigates the heat transfer characteristics of a thermoelectric generator. The influence of heat dissipation intensity to the sub-thermal resistances distribution is experimentally studied. Based on the thermal network analysis and finite time thermodynamics, an analytical model including all thermal resistances (in both thermocouples and external heat exchangers) is developed to predict the performance of the generator. The results show that the computed values of output power agree well with the experimental values. The heat transfer enhancement on the generator cold side greatly reduces the cold side temperature and thermal resistance, and obviously improves the output power. Compare with air natural convection cooling, the main thermal resistance changes from the resistance between the fins and the ambient to the thermal contact resistances between the generator and the heat sink at the conditions of forced convection and water cooling. This study may be guide the optimization of generator structure.

Numerical simulation and experimental study on electrothermal properties of carbon/glass fiber hybrid textile reinforced concrete

Carbon/glass fiber hybrid textile reinforced concrete is a relatively new composite material with good mechanical capacity and excellent electrical conductivity.Both small-scale slab heating experiments and numerical simulation are presented in this paper.Temperature variation curves obtained during heating indicate the effects of environmental temperature,heat-conducting layer thickness and electric heating power.Comparison of temperature rising between the situations with and without thermal isolation layer is given as well.The results indicate that the textile can form a good conductive heating network and generate enough heat to raise the temperature in the concrete when connected to a power supply,while the resistance of the slab remains stable during the heating.Numerical results are in good accordance with the experiments.Real time snow-melting experiment was conducted to verify the feasibility of deicing.The electrothermal properties of textile can be utilized for deicing and snow melting in a safe,environmentally friendly and efficient way.

Experimental Study on the Condensation of a Thermosyphon by Electrical Capacitance Tomography

The study on the condensation and the two-phase flow pattern in the condensation section is important to understand the operating mechanisms in a thermosyphon. In this paper, a new electric capacitance tomography(ECT) sensor was designed for the visualization measurement in a liquid by removing the shielding case and sealing with insulating hydrophobic material. It was successfully used to measure the condensation process in a thermosyphon under different operating temperatures. The thermosyphon was made of silica glass, and alcohol was used as a working fluid. The alcohol vapor was cooled to condense through the heat convection with the cooling water. The operating temperature was controlled by a heater with different power outputs. The experimental results show that the alcohol vapor condensed in stripes and unevenly on the wall surface at a low operating temperature. The liquid bridge will be formed periodically at the operating temperature of 90?C, and the time interval between two liquid bridges will be shorter with the increase of the operating temperature. At 117?C or even higher operating temperatures, the complete liquid bridge cannot be formed sometimes due to the difference of the growth rate of the surface wave around the circumference.

A preliminary experimental validation of superposition strategy in thermal management of integrated circuit with multiple hot-spots

Thermal management is a key issue in the integrated circuit(IC)design.In this paper,the superposition strategy was experimentally validated using a modeling IC device,which was fabricated by laboratory-level microfabrication technique.Metal thin film resistors on the top of dielectric layer were used to analogize the multiple hot-spots in the modeling IC device.The measured temperature rise with multiple hot-spots agrees well with the predictions given by the superposition calculations.With the help of the superposition strategy,thermal management of IC device can be significantly simplified by decomposing the system into sub-systems and optimizing each part individually.The influence coefficients in the superposition strategy extracted from the experimental measurement offer the IC designers a useful engineering tool to facility the thermal optimization and evaluate the thermal performance of IC devices.

Measurement of high-dynamic temperature field using high-speed quadriwave lateral shearing interferometer

An approach to measure a high-dynamic two-dimensional(2 D) temperature field using a high-speed quadriwave lateral shearing interferometer(QWLSI) is proposed. The detailed theoretical derivation to express the wavefront reconstruct principle of the proposed method is presented. The comparison experiment with thermocouples shows that the temperature field measurement using QWLSI has a precision of ±0.5 °C. An experiment for measuring the highdynamic temperature field generated by an electrical heater is carried out. A 200 frame rate temperature field video with 512 × 512 resolution is obtained finally. Experimental results show that the temperature field measurement system using a QWLSI has the advantage of high sensitivity and high resolution.