The stir casting technique was used to fabricate aluminum2024matrix hybrid composites reinforced with SiC(5%,mass fraction)and red mud(5%-20%,mass fraction)particles.The developed composites were characterized by usin...The stir casting technique was used to fabricate aluminum2024matrix hybrid composites reinforced with SiC(5%,mass fraction)and red mud(5%-20%,mass fraction)particles.The developed composites were characterized by using scanning electron microscopy(SEM)and electron dispersive spectrum(EDS)techniques.Further,Taguchi’s approach of experimental design was used to examine the tensile strength of the hybrid composites(with minimum number of experiments).It was found that the reinforcing particles were well dispersed and adequately bonded in the hybrid composites.The density and porosity of the hybrid composites were reduced with the increase in reinforcement content.The tensile strength of the composites increased with the increase in the red mud content and the ageing time.The developed model indicated that the red mud content had the highest influence on the tensile strength response followed by the ageing time.Overall,it was found that Al2024/SiC/red mud composites exhibited superior tensile strength(about34%higher)in comparison to the Al2024alloy under optimized conditions.展开更多
The LiMn2O4/grapbite battery was fabricated and its 3 C/10 V overcharge performance was studied. Spinel LiMn2O4 was synthesized by solid-state method and 325680-type size full battery was fabricated. The structure and...The LiMn2O4/grapbite battery was fabricated and its 3 C/10 V overcharge performance was studied. Spinel LiMn2O4 was synthesized by solid-state method and 325680-type size full battery was fabricated. The structure and morphology of the powders were characterized by XRD and SEM technique, respectively. The battery explodes after 3 C/10 V overcharged test, and surface temperature of the battery case arrives at 290 ℃ in 12 s after exploding. Black air is given out with blast. Carbon, MnO, and Li2CO3 are observed in the exploded powders. The cathode electrode remains spinel structure with 5.0 V charged. Cracks in the cathode electrode particles are detected with the increase of voltage by SEM technique. The 5.0 V charged electrode can decompose into Mn3O4 at 400 ℃. It is demonstrated that the decomposition of 5.0 V charged electrode can be promoted and Mn^4＋ can be deoxidized to Mn^2＋ by carbon and electrolyte through the simulation of blast process.展开更多
Effect of titanium dioxide （TiO2） and carbon additives in the respective positive and negative material properties and the influence on the performance of the battery were investigated. The electrode samples were ch...Effect of titanium dioxide （TiO2） and carbon additives in the respective positive and negative material properties and the influence on the performance of the battery were investigated. The electrode samples were characterized by BET （Brunauer Emmett Teller）, XRD （X-ray diffractometer）, SEM （scanning electron microscopy） and EIS （electrochemical impedance spectroscopy） to understand the surface area, phase, structure, morphology and electrical conductivity of the respective electrode material. The surface area was obtained as 2.312 m2＂g＂l and 0.892 m2＂g＂1, respectively for 12% of activated carbon in the expander of negative and 0.70% of TiO2 （Titanium dioxide） in the PAM （positive active material）. The structural analysis reveals an increase in the tetrabasic lead sulfate and also evidenced by well grown crystals in the PAM with the TiO2, respectively obtained by XRD and SEM techniques. The impedance spectra analysis shows an increase of electrical conductivity of negative active mass with temperature. The battery results showing two fold enhancements in the charge acceptance were attributed to the high surface area activated carbon in the NAM （negative active material）. The materials properties of electrodes and their influence on the battery performance were discussed.展开更多
文摘The stir casting technique was used to fabricate aluminum2024matrix hybrid composites reinforced with SiC(5%,mass fraction)and red mud(5%-20%,mass fraction)particles.The developed composites were characterized by using scanning electron microscopy(SEM)and electron dispersive spectrum(EDS)techniques.Further,Taguchi’s approach of experimental design was used to examine the tensile strength of the hybrid composites(with minimum number of experiments).It was found that the reinforcing particles were well dispersed and adequately bonded in the hybrid composites.The density and porosity of the hybrid composites were reduced with the increase in reinforcement content.The tensile strength of the composites increased with the increase in the red mud content and the ageing time.The developed model indicated that the red mud content had the highest influence on the tensile strength response followed by the ageing time.Overall,it was found that Al2024/SiC/red mud composites exhibited superior tensile strength(about34%higher)in comparison to the Al2024alloy under optimized conditions.
基金Project(2007CB613607) supported by the National Basic Research Program of China
文摘The LiMn2O4/grapbite battery was fabricated and its 3 C/10 V overcharge performance was studied. Spinel LiMn2O4 was synthesized by solid-state method and 325680-type size full battery was fabricated. The structure and morphology of the powders were characterized by XRD and SEM technique, respectively. The battery explodes after 3 C/10 V overcharged test, and surface temperature of the battery case arrives at 290 ℃ in 12 s after exploding. Black air is given out with blast. Carbon, MnO, and Li2CO3 are observed in the exploded powders. The cathode electrode remains spinel structure with 5.0 V charged. Cracks in the cathode electrode particles are detected with the increase of voltage by SEM technique. The 5.0 V charged electrode can decompose into Mn3O4 at 400 ℃. It is demonstrated that the decomposition of 5.0 V charged electrode can be promoted and Mn^4＋ can be deoxidized to Mn^2＋ by carbon and electrolyte through the simulation of blast process.
文摘Effect of titanium dioxide （TiO2） and carbon additives in the respective positive and negative material properties and the influence on the performance of the battery were investigated. The electrode samples were characterized by BET （Brunauer Emmett Teller）, XRD （X-ray diffractometer）, SEM （scanning electron microscopy） and EIS （electrochemical impedance spectroscopy） to understand the surface area, phase, structure, morphology and electrical conductivity of the respective electrode material. The surface area was obtained as 2.312 m2＂g＂l and 0.892 m2＂g＂1, respectively for 12% of activated carbon in the expander of negative and 0.70% of TiO2 （Titanium dioxide） in the PAM （positive active material）. The structural analysis reveals an increase in the tetrabasic lead sulfate and also evidenced by well grown crystals in the PAM with the TiO2, respectively obtained by XRD and SEM techniques. The impedance spectra analysis shows an increase of electrical conductivity of negative active mass with temperature. The battery results showing two fold enhancements in the charge acceptance were attributed to the high surface area activated carbon in the NAM （negative active material）. The materials properties of electrodes and their influence on the battery performance were discussed.
