CFD-DEM simulation of fluid-solid flow of a tapered column separation bed

Research on recycling waste Printed Circuit Boards(PCB) is at the forefront of preventing environmental pollution and finding ways to recycle resources.The Tapered Column Separation Bed(TCSB) is invented aiming at disposing the problem that fine particles of waste printed circuit boards cannot be separated efficiently so as to obtain further insight about the underlying mechanisms and demonstrate the separation feasibility in the tapered column separation bed.In this work,a Computational Fluid Dynamics(CFD) coupled with Discrete Element Method(DEM) model for two-phase flow has been extended to simulate the fluid-solid flow in the tapered column separation bed.Its validity is demonstrated by its successful capturing the key features of particles' flow pattern,velocity,the pressure distribution,the axial position with time and axial force for particles with different densities.Simulation results show that the plastic particles and resin particles become overflow,while copper particles,iron particles and aluminum particles successively become underflow,with a discharge water flow rate of 1 m^3/h,an obliquity of 30°.The simulated results agree reasonably well with the experimental observation.Using this equipment to separate waste PCBs is feasible,theoretically.

Waveforms analysis and optimization of new electro-hydraulic excitation technology

A new electro-hydraulic exciter that consists of rotary valve and micro-displacement double-functioned hydraulic cylinder was proposed to realize different kinds of waveforms.Calculated fluid dynamics(CFD) simulation of rotary valve orifice reveals that orifice exists the two-throttle phenomenon.According to the finding,the revised flow area model was established.Vibration waveforms analysis was carried out by means of mathematic model and the related experiments were validated.Furthermore,as a new analysis indicator,saturation percentage was introduced first.The experimental results indicate that the revised flow area model is more accurate compared to the original one,and vibration waveforms can be optimized through suitable spool parameters and the revised cylinder structure.

CFD simulation of high-temperature effect on EHD characteristics in a wire-plate electrostatic precipitator

A computational fluid dynamics （CFD） model is carried out to describe the wire-plate electrostatic precipitator （ESP） in high temperature conditions, aiming to study the effects of high temperature on the electro- hydrodynamic （EHD） characteristics. In the model, the complex interactions at high temperatures between the electric field, fluid dynamics and the particulate flow are taken into account. We apply different numerical methods for different fields, including an electric field model, Euler-Lagrange particle-laden flows model, and particle charging model. The effects of high temperature on ionic wind, EHD characteristics and collection effi- ciency are investigated. The numerical results show high temperature causes more significant effects of the ionic wind on the gas secondary flow. High viscosity of gas at high temperature makes particles follow the gas flow pattern more closely. High temperature reduces the surface electric strength, so that the mean electric strength weakens the space charging. On the contrary, there is an increase in the diffusion charging at high tem- perature compared with at low temperature. High temperature increases the ratio of mean drag force over mean electrostatic force actin~ on the ~atticles which mav contribute to a decline of collection efficiencv.

Corona-Support for the Entirety of High Energetic Disk

Based on results obtained from the study for MHD （magneto-hydrodynamics） of advective accretion disk, which are applied to real source showing typical values for CBS （close binary star-system）, it will investigate on self-structuring in the disk under the impact of the distribution of leading parameters （density, velocity ...）. The paper is considering the problem of development of the corona and will analyze the process of interaction of the plasma with the magnetic field in connection to support for the instabilities.

Two Independent Numerical Studies Demonstrating How to Efficiently Eliminate Electrolysis Side Reactions in Magneto-Hydro-Dynamic Pumping System

In this work, a numerical study for designing a new kind of MHD （Magneto-Hydrn-Dynamic） pumps is presented. This technique makes a compromise between electrolysis prevention and high flow rate performance. This technique should eliminate electrolytic bubble generation, electrodes wear and fluid propriety modification. All these side phenomena are prevented by considering isolated electrodes. The numerical presented results in this paper demonstrate that continuous MHD pumping is possible with isolated electrodes. The MHD excitation combines a high frequency altering current with a low frequency altering magnetic field. In order to validate our results, two independent theoretical methods for computing flow rate are followed. The two presented independent approaches show that high flow rate is possible even with isolated electrodes. To overcome the problem of dimensioning this kind of pumps, a generic numerical analysis is proposed. Hence, the pump performances as functions of the external parameter are studied and tools to calculate for a given fluid and the optimal high frequency regime are provided.

Enhanced single-nanoparticle collisions for the hydrogen evolution reaction in a confined microchannel

Single nanoparticle(NP)collisions technique has been widely employed in electrocatalysis.However,the short collision duration of single NPs hinders the further improvement in their electrocatalytic performance.Here,to increase the dynamic collision duration of single NPs in the electron tunneling region,enhanced near-wall hindered diffusion is introduced in the stochastic collision process by coupling a Au ultramicroelectrode(UME)with a confined microchannel.In the case of single palladium nanoparticle(Pd NP)collisions for the hydrogen evolution reaction(HER),the hydrodynamic trapping confined in the microchannel effectively permits the activation of the HER on the single Pd NPs.The microchannel-based Au UME is promising in the application of single-NP collisions to energy conversion.

Building Effects on a Horizontal-Axis Micro Wind Turbine： Experimental and Fluid-Dynamic Analysis

In this work, the efficiency ofa 1 kWp horizontal-axis wind turbine which is installed on the roof of the engineering building at the University of Salento has been evaluated, by means of CFD （computational fluid dynamic） and experimental data. Particularly, the influence of the building on the micro wind turbine performance has been studied and the numerical results （wind velocity fields and turbulence intensity above the building） have been compared with the experimental data collected over a period of three years. The results have shown that horizontal-axis wind turbines suffer from wake effect due to buildings, therefore, best sites in urban area have to be identified by a careful fluid dynamic analysis aimed at evaluating all causes that can reduce significantly the performance of the generator： in fact, building should allow to exploit increased wind intensity, but often this advantage is voided by turbulence phenomena, as in the case under investigation where the measured aerogenerator efficiency is lower than the nominal performance curve. Then, the best site can be found by crossing the contours of wind velocity with the turbulence intensity fields： in this way it is possible to localize an area （best location） where the aerogenerator can give maximum performance.

Improving the Performance of an Electro-Hydraulic Load-Sensing Proportional Control Valve

The paper deals with the simulation and the experimental verification of the hydraulic behavior of an electro-hydraulic load-sensing proportional control valve. An innovative CAE （computer aided engineering） methodology, developed combining CFD （computational fluid dynamics） simulations with lumped and distributed numerical modeling, is firstly introduced and tailored by comparing the numerical results with measurements coming from an experimental campaign performed for a wide range of pressure loads and metered flow rates. Then, both the reliability and the limits of the numerical approach are highlighted through a detailed numerical vs. experimental comparison, involving the pressure of the main hydraulic lines, the flow rate through the first section and the local compensator displacement. Finally, the CAE methodology has been applied for assessing the internal ducts hydraulic permeability and the local compensator spring pre-load influence on the control valve metering curves. At the end of this analysis, an optimized design configuration, featuring a maximum controlled volumetric flow rate increased of more than 25%, has been proposed.

Design of High-Speed PM Synchronous Motor Thermal and Mechanical Analyzes Study for Aerospace Retraction Wheel Motor Application

A 3-D modeling of FEA （finite element analysis） design provides for high-speed synchronous with PMs （permanent magnets） applied in aerospace application will be examined under design considerations ofn = 12,000 rpm, short-duty operation, and etc. for an ARWM （aerospace retraction wheel motor）. First, lumped-elements will be fine-tuned following numerical method results is reported steady-state and transient solutions. Besides, the equations of thermal modeling such as Re, N,,, G,. and Pr numbers in order to calculate heat-transfer coefficient of convection on the rotor and stator surfaces in the air-gap have calculated. This section illustrates the temperature distribution of each point in a clear view. By CFD （fluid dynamic analysis） analysis, the fluid dynamics were modeled, pressure and velocity streamlines of cooling-flow have analyzed. An optimization algorithm was derived in order to have optimized number of water-channels as well. Second, calculation of nodal and tangential forces which deal with mechanical stresses of the ARWM have represented. The paper discusses an accurate magnetic-field analysis that addresses equivalent stress distribution in the magnetic core through using the transient FEA to estimate motor characteristics. The whole model shear and normal mechanical stresses and total deformation oftbe ARWM has been investigated by transient FEA. The end-winding effects were included by the authors.

Numerical analysis of thermal fluid transport behavior during electron beam welding of 2219 aluminum alloy plate

A two-dimensional mathematical model based on volume-of-fluid method is proposed to investigate the heat transfer,fluidflow and keyhole dynamics during electron beam welding(EBW)on20mm-thick2219aluminum alloy plate.In the model,anadaptive heat source model tracking keyhole depth is employed to simulate the heating process of electron beam.Heat and masstransport of different vortexes induced by surface tension,thermo-capillary force,recoil pressure,hydrostatic pressure and thermalbuoyancy is coupled with keyhole evolution.A series of physical phenomena involving keyhole drilling,collapse,reopening,quasi-stability,backfilling and the coupled thermal field are analyzed systematically.The results indicate that the decreased heat fluxof beam in depth can decelerate the keyholing velocity of recoil pressure and promote the quasi-steady state.Before and close to thisstate,the keyhole collapses and complicates the fluid transport of vortexes.Finally,all simulation results are validated againstexperiments.

Riser VIV and its numerical simulation

This paper summarizes some of the typical riser vortex-induced vibration （VIV） problems in subsea oil and gas developments, and presents the corresponding computational fluid dynamics （CFD） time domain simula- tion results to address these problems. First, the CFD time domain simulation approach was applied to analyze the wake field behind a stationary cylinder and a vibrating cylinder. Then a vertical riser VIV response under uniform current was studied. The VIV response time histories revealed some valuable clues that could lead to explanation of the higher harmonics. After that, a vertical riser VIV response under shear current was investigated. A 3 000 ft （1 ft=-0.304 8 m） water depth top tensioned riser was sized, and its VIV responses under uniform and shear current were studied. Then this paper continues to discuss one catenary flexible riser VIV response during normal lay. Last, the time domain simulation approach was applied to a partially submerged flexible jumper, to study the jumper VIV behavior, and dynamic motion envelopes. It was demonstrated that the time domain simulation ap- proach is able to disclose details of the flow field, vortex shedding pattern, and riser dynamic behavior, and han- dle different tvoes of risers under different Woe of currents.

Numerical simulation of a direct internal reforming solid oxide fuel cell using computational fluid dynamics method

A detailed mathematical model of a direct internal reforming solid oxide fuel cell(DIR-SOFC) incorporating with simulation of chemical and physical processes in the fuel cell is presented. The model is developed based on the reforming and electrochemical reaction mechanisms,mass and energy conservation,and heat transfer. A computational fluid dynamics(CFD) method is used for solving the complicated multiple partial differential equations(PDEs) to obtain the numerical approximations. The resulting distributions of chemical species concentrations,temperature and current density in a cross-flow DIR-SOFC are given and analyzed in detail. Further,the influence between distributions of chemical species concentrations,temperature and current density during the simulation is illustrated and discussed. The heat and mass transfer,and the kinetics of reforming and electrochemical reactions have significant effects on the parameter distributions within the cell. The results show the particular characteristics of the DIR-SOFC among fuel cells,and can aid in stack design and control.

Calculation of Steady SF_6 Gas Flow through a 420 kV Circuit Breaker Nozzle and Electric Field Distribution

Special interest in current interruptions is dedicated to the processes close to the current zero instant, the so-called interaction region, which determines the circuit breakers＇ performance. The quantities of interest in this region are the distribution of temperature, density and pressure, velocity and gas mass flow along the electric arc axis, as well as the distribution of electric stress between contacts Calculation of steady SF_6 gas flow through the nozzle of a 420 kV circuit breaker at the current zero instant, for different arcing durations, was carried out using a commercial CFD （computational fluid dynamics） simulation tool. The calculation results were used to get insight into improvement possibilities of the SF_6 gas flow model used in the software for computer simulation of HV （high-voltage） circuit breakers. Electric field calculation results were performed for the same 420 kV circuit breaker, in order to estimate the breakdown voltage at the current zero instant.

Thermal Modeling and Cooling Analysis of High-power Lithium Ion Cells

The heat generation model and three-dimensional computational fluid dynamics model for lithium ion cells were established with boundary conditions defined.In order to provide a better insight about the behaviors of high-power lithium ion cells under realistic discharge conditions,the temperature difference of the cells and an active thermal management system with a pure air-cooling mode were analyzed and predicted with the factors affecting the unevenness of temperature field discussed.The results show a significant effect of the cooling flow rate on the temperature rise of the cells for all discharge rates.Average surface temperatures are relatively uniform at lower discharge rate that makes it easier to control the temperature of the pack.Cell temperatures are expected to rise significantly toward the end of discharge and they show non-uniformity at higher discharge rates.Adequate air flow rate of active cooling is required at high discharge rate and high ambient temperature for practical pack thermal management system.

Electrostatic Surface Waves on Semi-Bounded Quantum Electron-Hole Semiconductor Plasmas

The electrostatic surface waves on semi-bounded quantum electron-hole semiconductor plasmas are studied within the framework of the quantum hydrodynamic model, including the electrons and holes quantum recoil effects,quantum statistical pressures of the plasma species, as well as exchange and correlation effects. The dispersion characteristics of surface electrostatic oscillations are investigated by using the typical values of Ga As, Ga Sb and Ga N semiconductors. Numerical results show the existence of one low-frequency branch due to the mass difference between the electrons and holes in addition to one high-frequency branch due to charge-separation effects.

A Theoretical Model to Explain the Mechanism of Electromagnetic Wave Propagation Along Cylindrical Micelles

A theoretical model to explain the mechanism of the electromagnetic wave propagation in the quasi two-dimensional layer of counterions adjacent to the surface of a charged cylindrical membrane is presented. By using Maxwell and hydrodynamic equations with appropriate boundary conditions, general expression of dispersion relation is obtained for the electromagnetic wave with mixed TE and TM modes.