Static corrections using the conventional method are basically conducted in two steps, the weathering correction followed by the correction from the top of the sub-weathering to the unified datum. However, the convent...Static corrections using the conventional method are basically conducted in two steps, the weathering correction followed by the correction from the top of the sub-weathering to the unified datum. However, the conventional method fails to well deal with statics problems in case the top of the sub-weathering is sharply undulated and the lateral velocity of the sub-weathering varies significantly. This brings us to the introduction of a smooth intermediate reference datum （IRD） located under the top of the sub-weathering, which helps to further increase the accuracy of statics based on the weathering corrections, and ensures the imaging quality. Good results based on the IRD technique have been achieved in the complex areas in western China. This paper discusses the IRD functions, its application requirements, and selection of related parameters. Some typical sections for comparison are also given in this paper.展开更多
In deep underground mining, the surrounding rocks are very soft with high stress. Their deformation and destruction are serious, and frequent failures occur on the bolt support. The failure mechanism of bolt support i...In deep underground mining, the surrounding rocks are very soft with high stress. Their deformation and destruction are serious, and frequent failures occur on the bolt support. The failure mechanism of bolt support is proposed to solve these problems. A calculation theory is established on the bond strength of the interface between the anchoring agent and surrounding rocks. An analysis is made on the influence law of different mechanical parameters of surrounding rocks on the interfacial bond strength. Based on the research, a new high-strength bolt-grouting technology is developed and applied on site. Besides, some helpful engineering suggestions and measures are proposed. The research shows that the serious deformation and failure, and the lower bond strength are the major factors causing frequent failures of bolt support. So, the bolt could not give full play to its supporting potential. It is also shown that as the integrity, strength, interface dilatancy and stress of surrounding rocks are improved, the bond strength will increase. So, the anchoring force on surrounding rocks can be effectively improved by employing an anchoring agent with high sand content, mechanical anchoring means, or grouting reinforcement. The new technology has advantages in a high strength, imposing pre-tightening force, and giving full play to the bolt supporting potential. Hence, it can improve the control effect on surrounding rocks. All these could be helpful references for the design of bolt support in deep underground mines.展开更多
It is still challenging to develop suitable cathode structures for high-rate and stable aqueous Zn-ion batteries.Herein,a phosphating-assisted interfacial engineering strategy is designed for the controllable conversi...It is still challenging to develop suitable cathode structures for high-rate and stable aqueous Zn-ion batteries.Herein,a phosphating-assisted interfacial engineering strategy is designed for the controllable conversion of NiCo_(2)S_(4) nanosheets into heterostructured NiCoP/NiCo_(2)S_(4) as the cathodes in aqueous Zn-ion batteries.The multicomponent heterostructures with rich interfaces can not only improve the electrical conductivity but also enhance the diffusion pathways for Zn-ion storage.As expected,the NiCoP/NiCo_(2)S_(4) electrode has high performance with a large specific capacity of 251.1 mA h g^(−1) at a high current density of 10 A g^(−1) and excellent rate capability(retaining about 76%even at 50 A g^(−1)).Accordingly,the Zn-ion battery using NiCoP/NiCo_(2)S_(4) as the cathode delivers a high specific capacity(265.1 mA h g^(−1) at 5 A g^(−1)),a long-term cycling stability(96.9%retention after 5000 cycles),and a competitive energy density(444.7W h kg^(−1) at the power density of 8.4 kW kg^(−1)).This work therefore provides a simple phosphating-assisted interfacial engineering strategy to construct heterostructured electrode materials with rich interfaces for the development of high-performance energy storage devices in the future.展开更多
We detected a severe haze process in Guangzhou area with lidar and microwave radiometer, performed an inversion to get boundary layer height by wavelet covariance transform, and analyzed the correlation between meteor...We detected a severe haze process in Guangzhou area with lidar and microwave radiometer, performed an inversion to get boundary layer height by wavelet covariance transform, and analyzed the correlation between meteorological factors of boundary layer and visibility from the perspective of dynamical and thermodynamic structures. Our results indicate that the boundary layer height shows significant daily changes, consistent with ground visibility variation. During the cleaning process, the boundary layer height exceeded 1 km; during severe haze, the height was only 500 m. Temperature gradient of 50–100 m, which was 30 h lag, was remarkably correlated with visibility, with the correlation coefficient of 0.77. High layer visibility(255 m) and low layer stability were significantly anticorrelation, and the maximum anticorrelation coefficient was up to-0.76 in cleaning days and-0.49 in haze days. In the related boundary layer meteorological factors, surface ventilation coefficient was linearly correlated with ground visibility, with the greatest correlation coefficient of 0.88. The correlation coefficients of boundary layer height, ground wind velocity, relative humidity and ground visibility were 0.76, 0.67, and-0.77, respectively. There was a strong correlation between different meteorological factors. The dominant meteorological factor during this haze process was surface ventilation coefficient. In the area without boundary layer height sounding, ground visibility and wind velocity could be used to estimate boundary layer height.展开更多
文摘Static corrections using the conventional method are basically conducted in two steps, the weathering correction followed by the correction from the top of the sub-weathering to the unified datum. However, the conventional method fails to well deal with statics problems in case the top of the sub-weathering is sharply undulated and the lateral velocity of the sub-weathering varies significantly. This brings us to the introduction of a smooth intermediate reference datum （IRD） located under the top of the sub-weathering, which helps to further increase the accuracy of statics based on the weathering corrections, and ensures the imaging quality. Good results based on the IRD technique have been achieved in the complex areas in western China. This paper discusses the IRD functions, its application requirements, and selection of related parameters. Some typical sections for comparison are also given in this paper.
基金Projects(51304125,51379114)supported by the National Natural Science Foundation of ChinaProject(BS2013NJ004)supported by Award Fund for Outstanding Young and Middle-Aged Scientist of Shangdong Province,ChinaProject(201301004)supported by the Innovation Fund for Postdoctor of Shandong Province,China
文摘In deep underground mining, the surrounding rocks are very soft with high stress. Their deformation and destruction are serious, and frequent failures occur on the bolt support. The failure mechanism of bolt support is proposed to solve these problems. A calculation theory is established on the bond strength of the interface between the anchoring agent and surrounding rocks. An analysis is made on the influence law of different mechanical parameters of surrounding rocks on the interfacial bond strength. Based on the research, a new high-strength bolt-grouting technology is developed and applied on site. Besides, some helpful engineering suggestions and measures are proposed. The research shows that the serious deformation and failure, and the lower bond strength are the major factors causing frequent failures of bolt support. So, the bolt could not give full play to its supporting potential. It is also shown that as the integrity, strength, interface dilatancy and stress of surrounding rocks are improved, the bond strength will increase. So, the anchoring force on surrounding rocks can be effectively improved by employing an anchoring agent with high sand content, mechanical anchoring means, or grouting reinforcement. The new technology has advantages in a high strength, imposing pre-tightening force, and giving full play to the bolt supporting potential. Hence, it can improve the control effect on surrounding rocks. All these could be helpful references for the design of bolt support in deep underground mines.
基金supported by the National Natural Science Foundation of China(51602049 and 51708504)China Postdoctoral Science Foundation(2017M610217 and 2018T110322)。
文摘It is still challenging to develop suitable cathode structures for high-rate and stable aqueous Zn-ion batteries.Herein,a phosphating-assisted interfacial engineering strategy is designed for the controllable conversion of NiCo_(2)S_(4) nanosheets into heterostructured NiCoP/NiCo_(2)S_(4) as the cathodes in aqueous Zn-ion batteries.The multicomponent heterostructures with rich interfaces can not only improve the electrical conductivity but also enhance the diffusion pathways for Zn-ion storage.As expected,the NiCoP/NiCo_(2)S_(4) electrode has high performance with a large specific capacity of 251.1 mA h g^(−1) at a high current density of 10 A g^(−1) and excellent rate capability(retaining about 76%even at 50 A g^(−1)).Accordingly,the Zn-ion battery using NiCoP/NiCo_(2)S_(4) as the cathode delivers a high specific capacity(265.1 mA h g^(−1) at 5 A g^(−1)),a long-term cycling stability(96.9%retention after 5000 cycles),and a competitive energy density(444.7W h kg^(−1) at the power density of 8.4 kW kg^(−1)).This work therefore provides a simple phosphating-assisted interfacial engineering strategy to construct heterostructured electrode materials with rich interfaces for the development of high-performance energy storage devices in the future.
基金supported by the National Basic Research Program of China(Grant No.2011CB403403)the National Natural Science Foundation of China(Grant Nos.41205123,41375156,1175117)Guangdong Provincial Natural Science Foundation(Grant No.10151008019000004)
文摘We detected a severe haze process in Guangzhou area with lidar and microwave radiometer, performed an inversion to get boundary layer height by wavelet covariance transform, and analyzed the correlation between meteorological factors of boundary layer and visibility from the perspective of dynamical and thermodynamic structures. Our results indicate that the boundary layer height shows significant daily changes, consistent with ground visibility variation. During the cleaning process, the boundary layer height exceeded 1 km; during severe haze, the height was only 500 m. Temperature gradient of 50–100 m, which was 30 h lag, was remarkably correlated with visibility, with the correlation coefficient of 0.77. High layer visibility(255 m) and low layer stability were significantly anticorrelation, and the maximum anticorrelation coefficient was up to-0.76 in cleaning days and-0.49 in haze days. In the related boundary layer meteorological factors, surface ventilation coefficient was linearly correlated with ground visibility, with the greatest correlation coefficient of 0.88. The correlation coefficients of boundary layer height, ground wind velocity, relative humidity and ground visibility were 0.76, 0.67, and-0.77, respectively. There was a strong correlation between different meteorological factors. The dominant meteorological factor during this haze process was surface ventilation coefficient. In the area without boundary layer height sounding, ground visibility and wind velocity could be used to estimate boundary layer height.
