This paper describes the principles of operation and the physical model of an advanced AC-DC converter generator （with the electronic converter acting as an AC-DC rectifier with reverse-conducting MOSFETs （metal-oxi...This paper describes the principles of operation and the physical model of an advanced AC-DC converter generator （with the electronic converter acting as an AC-DC rectifier with reverse-conducting MOSFETs （metal-oxide semiconductor field-effect transistors） as fast-electronic switches with a relatively low ON-state voltage drop） for HSVs. An AC-DC converter, when seen as an AC-DC rectifier, can be used in many fields, e.g., for multi-functional AC-DC/DC-AC convener generator^starter and conventional DC-AC convener motors and AC-DC converter generators or generator sets, welding machines, etc. The paper also describes a novel AC-DC convener, with reverse-conducting transistors and without the use of optoelectronic separation （which does not require a separate power supply）, which may be easily realized in IC （integrated-circuit） technology. Computer simulation allows for waveform evaluation for timing analysis of all components of the AC-DC-converter＇s physical model, both during normal operation as well as in some states of emergency. The paper also presents the results of bench experimental studies where the MOSFETs were used as fast-electronic switches with a relatively low ON-state voltage drop. For experimental studies, a novel AC-DC converter has been put together on the Mitsubishi FM600TU-3A module. The AC-DC converter with reverse-conducting transistors in a double-way connection has a lot of advantages compared to the conventional AC-DC convener acting as a diode rectifier, such as higher energy efficiency and greater reliability resulting from the lower temperature of electronic switches.展开更多
A direct conversion receiver with optimized tolerance to local carrier interference is designed and implemented in a 0.18μm 1P6M mixed-signal CMOS process for a 900MHz RFID reader transceiver. A baseband amplifier wi...A direct conversion receiver with optimized tolerance to local carrier interference is designed and implemented in a 0.18μm 1P6M mixed-signal CMOS process for a 900MHz RFID reader transceiver. A baseband amplifier with series feedback topology is proposed to achieve passive mixer buffering,baseband DC cancellation,and signal amplification simultaneously. The receiver has a measured input ldB compression point of - 4dBm and a sensitivity of - 70dBm when 10dB SNR for digital demodulation is required. The receiver is integrated in a reader transceiver chip and consumes 90mA from a 1.8V supply.展开更多
With the use of this novel average model for Single Stage Flyback PFC+Flyback DC/DC converter, voltage control mode, peak current control mode and average current control mode can be simulated easily by changing the m...With the use of this novel average model for Single Stage Flyback PFC+Flyback DC/DC converter, voltage control mode, peak current control mode and average current control mode can be simulated easily by changing the model's parameters. It can be used to do various analysis not only for small signal and static behavior but also for large signal and dynamic behavior of the converter. By using this average model the simulation speed can be improved by 2 orders of magnitude above that obtained by using the conventional switched model. It can be applied to optimize the trade\|off between high power factor, voltage stress, current stress and good output performance while designing this kind of single stage PFC converter. A 60W single stage power factor corrector was built to verify the proposed model. The modeling principle can be applied to other Single Stage PFC topologies.展开更多
This paper presents and investigates planar and coaxial high frequency power transformers used for DC/DC converters in a three phase photo voltaic （PV） power systems. The winding structure including a Faraday shield...This paper presents and investigates planar and coaxial high frequency power transformers used for DC/DC converters in a three phase photo voltaic （PV） power systems. The winding structure including a Faraday shield between the primary and secondary windings is designed to minimize eddy current losses, skin and proximity effects, and to reduce the leakage inductance, and the inter winding coupling capacitance. Finite Element Method is employed to analyze the magnetic flux and eddy current distributions. The two different kinds of prototype high frequency transformers are designed and tested. The simulation and experiment results are demonstrated and compared with non-shielded transformers. The shielded transformers have achieved the expected results with a relatively small coupling capacitance, compared with the conventional high frequency transformer. This shield decreases the inter-winding coupling capacitance Cps. The topology of this shield has to be such that it acts as a Faraday screen while avoiding eddy current generation.展开更多
文摘This paper describes the principles of operation and the physical model of an advanced AC-DC converter generator （with the electronic converter acting as an AC-DC rectifier with reverse-conducting MOSFETs （metal-oxide semiconductor field-effect transistors） as fast-electronic switches with a relatively low ON-state voltage drop） for HSVs. An AC-DC converter, when seen as an AC-DC rectifier, can be used in many fields, e.g., for multi-functional AC-DC/DC-AC convener generator^starter and conventional DC-AC convener motors and AC-DC converter generators or generator sets, welding machines, etc. The paper also describes a novel AC-DC convener, with reverse-conducting transistors and without the use of optoelectronic separation （which does not require a separate power supply）, which may be easily realized in IC （integrated-circuit） technology. Computer simulation allows for waveform evaluation for timing analysis of all components of the AC-DC-converter＇s physical model, both during normal operation as well as in some states of emergency. The paper also presents the results of bench experimental studies where the MOSFETs were used as fast-electronic switches with a relatively low ON-state voltage drop. For experimental studies, a novel AC-DC converter has been put together on the Mitsubishi FM600TU-3A module. The AC-DC converter with reverse-conducting transistors in a double-way connection has a lot of advantages compared to the conventional AC-DC convener acting as a diode rectifier, such as higher energy efficiency and greater reliability resulting from the lower temperature of electronic switches.
基金the Science and Technology Commission of Shanghai Municipality(No.057062010)the EU BRIDGE Project(No.033546)~~
文摘A direct conversion receiver with optimized tolerance to local carrier interference is designed and implemented in a 0.18μm 1P6M mixed-signal CMOS process for a 900MHz RFID reader transceiver. A baseband amplifier with series feedback topology is proposed to achieve passive mixer buffering,baseband DC cancellation,and signal amplification simultaneously. The receiver has a measured input ldB compression point of - 4dBm and a sensitivity of - 70dBm when 10dB SNR for digital demodulation is required. The receiver is integrated in a reader transceiver chip and consumes 90mA from a 1.8V supply.
文摘With the use of this novel average model for Single Stage Flyback PFC+Flyback DC/DC converter, voltage control mode, peak current control mode and average current control mode can be simulated easily by changing the model's parameters. It can be used to do various analysis not only for small signal and static behavior but also for large signal and dynamic behavior of the converter. By using this average model the simulation speed can be improved by 2 orders of magnitude above that obtained by using the conventional switched model. It can be applied to optimize the trade\|off between high power factor, voltage stress, current stress and good output performance while designing this kind of single stage PFC converter. A 60W single stage power factor corrector was built to verify the proposed model. The modeling principle can be applied to other Single Stage PFC topologies.
文摘This paper presents and investigates planar and coaxial high frequency power transformers used for DC/DC converters in a three phase photo voltaic （PV） power systems. The winding structure including a Faraday shield between the primary and secondary windings is designed to minimize eddy current losses, skin and proximity effects, and to reduce the leakage inductance, and the inter winding coupling capacitance. Finite Element Method is employed to analyze the magnetic flux and eddy current distributions. The two different kinds of prototype high frequency transformers are designed and tested. The simulation and experiment results are demonstrated and compared with non-shielded transformers. The shielded transformers have achieved the expected results with a relatively small coupling capacitance, compared with the conventional high frequency transformer. This shield decreases the inter-winding coupling capacitance Cps. The topology of this shield has to be such that it acts as a Faraday screen while avoiding eddy current generation.
