交错并联磁集成双向DC/DC变换器的工作相数控制

在采用四相交错并联双向DC/DC变换器(BDC)拓扑的基础上,将变换器的4个分立电感磁集成为两个反向耦合电感,以减小开关器件及电感器的电流幅值和纹波,从而减小有源和无源损耗,消除局部过热点;分析了变换器的开关损耗和耦合电感损耗,提出了变换器的工作相数控制方法。实验验证了交错并联磁集成BDC损耗计算公式的正确性及工作相数控制方法的有效性。

一种多相交错并联磁耦合双向直流变换器效率优化策略

双向DC/DC变换器普遍存在轻载效率偏低的问题,针对这一难题提出了变换器最优工作相数控制策略,即根据负载的减小程度,适当减少工作相数,以消除未工作相的所有损耗,提高变换器轻载效率。分析变换器轻载时损耗,推导出效率计算公式。针对轻载减少工作相数会引起总输出电流纹波恶化的问题,提出采用交错并联磁集成技术,将四个分立电感集成为两个耦合电感以减小电感开关器件的相电流纹波,降低损耗,并结合移相控制和滤波电容设计进一步消除轻载切相后输出纹波增大的影响,最大程度降低其轻载工作损耗,实现变换器全负载范围高效率运行。仿真和实验证明所提出的轻载效率优化策略的正确性及移相加磁集成最优工作相数控制策略的有效性。

Experimental and Numerical Investigations of Single Drop Mass Transfer in Solvent Extraction Systems with Resistance in Both Phases

Numerical simulation of transient mass transfer to a single dropcontrolled by the internal resistance or by the resistance in bothphases was mathematically formulated and simulated in aboundary-fitted orthogonal coordinate system. The simulated resultson the transient mass transfer dominated by the internal resistanceare in good agreement with the Newman and Kronig-Brink models fordrops with low Reynolds number. When the drop Reynolds number is upto 200, the mass transfer coefficient from numerical simulation isvery low as compared with The Handlos-Baron model.

THE DESIGN OF AN ALL-DIGITAL PHASE-LOCKED LOOP WITH LOW JITTER BASED ON ISF ANALYSIS

A low jitter All-Digital Phase-Locked Loop （ADPLL） used as a clock generator is designed. The Digital-Controlled Oscillator （DCO） for this ADPLL is a seven-stage ring oscillator with the delay of each stage changeable. Based on the Impulse Sensitivity Function （ISF） analysis, an effective way is proposed to reduce the ADPLL＇s jitter by the careful design of the sizes of the inverters used in the DCO with a simple architecture other than a complex one. The ADPLL is implemented in a 0.18μm CMOS process with 1.SV supply voltage, occupies 0.046mm^2 of on-chip area. According to the measured results, the ADPLL can operate from 108MHz to 304MHz, and the peak-to-peak jitter is 139ps when the DCO＇s output frequency is 188MHz.

Digital AGC Based on Coherent Adjustment Cycle for DSSS Receiver

In order to meet the requirements for zero value stability of direct sequence spread spectrum(DSSS) signal processing in high dynamic scenario,digital automatic gain control(AGC) is employed to regulate power.However,conventional AGC causes degradation in the synchronization performance of DSSS receiver.Based on the theoretical analysis of the influence of digital AGC on DSSS signal synchronization,this paper proposes a new AGC algorithm,which is applicable to multi-channel digital DSSS signal receiver.By making power adjustment cycle and synchronization cycle coherent with each other adaptively,the influence of digital AGC on subsequent synchronization processing has been eliminated.Theoretical analysis,simulation results and experimental data verify the validity of the proposed algorithm.By virtue of the proposed algorithm,the influence of digital AGC on DSSS signal synchronization is eliminated.This algorithm applies to an aerospace engineering project successfully.

Numerical Simulation and Control of Two-Phase Flow with Evaporation in a Vertical Tube Submitted to a Conjugate Heat Transfer

A better understanding of two-phase flows with evaporation allows leading to an optimal design of evaporators. For that purpose, numerical simulations are very useful. In this paper, a numerical study has been carried out in order to model and simulate the combination of a two-phase flow with evaporation in a vertical tube. The VOF （volume-of-fluid） multiphase flow method and a phase-change model for the mass transfer have been used. For an accurate modeling, the effect of axial conduction has been also taken into account using a conjugate heat transfer model. Since thermal oscillations are undesirable as they can lead to the failure of the tube, flow instabilities have also been analyzed, using FFT （fast Fourier transforms）, in order to comprehend their behavior and influence. A control study of the flow instabilities in the tube is also presented. For that purpose tube inlet temperature has been varied using a gain control parameter.

Sediment control function of river notches

The purpose of this study is to investigate the control function and mechanisms of natural river notches. Physical and numerical experiments are analyzed in this study for two representative types of sediment events： high intensity and short duration Type A sediment disaster events, and low intensity and long duration Type B moderate non-disaster events. Two dimensionless parameters, sediment trapping rate and reduction rate of peak sediment transport, are defined to evaluate the sediment control function of river notches. Study results indicate that the contraction ratio of the notch has a significant influence on sediment control function, with high contraction ratios resulting in both high sediment-trapping and high reduction rates. River notches provide better sediment control during Type A events than Type B events. The sediment control mechanism of river notches is the result of multiple interactions among river flow, sediment transport, and riverbed variation. Analysis of these interactions supports the significant protection role of river notches on sediment control for disaster events.

Stochastic H_2/H_∞ Control with Random Coefcients

Abstract This paper is concerned with the mixed H2/H∞ control for stochastic systems with random coefficients, which is actually a control combining the H2 optimization with the H∞ robust performance as the name of H2/H∞ reveals. Based on the classical theory of linear-quadratic （LQ, for short） optimal control, the sufficient and necessary conditions for the existence and uniqueness of the solution to the indefinite backward stochastic Riccati equation （BSRE, for short） associated with H∞ robustness are derived. Then the sufficient and necessary conditions for the existence of the H2/H∞ control are given utilizing a pair of coupled stochastic Pdccati equations.

Numerical Simulations and Analyses of Temperature Control Loop Heat Pipe for Space CCD Camera

As one of the key units of space CCD camera,the temperature range and stability of CCD components affect the image's indexes.Reasonable thermal design and robust thermal control devices are needed.One kind of temperature control loop heat pipe(TCLHP) is designed,which highly meets the thermal control requirements of CCD components.In order to study the dynamic behaviors of heat and mass transfer of TCLHP,particularly in the orbital flight case,a transient numerical model is developed by using the well-established empirical correlations for flow models within three dimensional thermal modeling.The temperature control principle and details of mathematical model are presented.The model is used to study operating state,flow and heat characteristics based upon the analyses of variations of temperature,pressure and quality under different operating modes and external heat flux variations.The results indicate that TCLHP can satisfy the thermal control requirements of CCD components well,and always ensure good temperature stability and uniformity.By comparison between flight data and simulated results,it is found that the model is to be accurate to within 1℃.The model can be better used for predicting and understanding the transient performance of TCLHP.

Effects of first-order chemical reactions on the dispersion coefficient associated with laminar flow through the lungs

This paper aims to look into the determination of effective area-average concentration and dispersion coefficient associated with unsteady flow through a small-diameter tube where a solute undergoes first-order chemical reaction both within the fluid and at the boundary. The reaction consists of a reversible component due to phase exchange between the flowing fluid and the wall layer, and an irreversible component due to absorption into the wall. To understand the dispersion, the governing equations along with the reactive boundary conditions are solved numerically using the Finite Difference Method. The resultant equation shows how the dispersion coefficient is influenced by the first-order chemical reaction. The effects of various dimensionless parameters e.g. Da （the Damkohler number）, a （phase partitioning number） and F （dimensionless absorption number） on dispersion are discussed. One of the results exposes that the dispersion coefficient may approach its steady-state limit in a short time at a high value of Damkohler number （say Da 〉 10） and a small but nonzero value of absorption rate （say P 〈0.5）.

Simplified Numerical Study of Evaporation Processes Inside Vertical Tubes

The paper presents a simplified numerical model of evaporation processes inside vertical tubes.In this model only the temperature fields in the fluid domain(the liquid or two-phase mixture) and solid domain(a tube wall) are determined.Therefore its performance and efficiency is high.The analytical formulas,which allow calculating the pressure drop and the distribution of heat transfer coefficient along the tube length,are used in this model.The energy equation for the fluid domain is solved with the Control Volume Method and for the solid domain with the Finite Element Method in order to determine the temperature field for the fluid and solid domains.