多晶TiNi和CuZnAl形状记忆合金中的织构转变

用 X射线织构仪测定了 Ti Ni和 Cu Zn Al合金的母相奥氏体、产品相马氏体的极图 ,计算了测定极图各自的位向分布函数 .分析结果表明 ,Ti Ni合金奥氏体具有一个弱的织构组元 {4 ,0 ,3}〈0 ,1 ,0〉和一个α纤维织构 ,Ti Ni Cu合金马氏体有 6个主要的织构组元 ;Cu Zn Al合金奥氏体织构是一个纤维织构 ,其纤维轴为〈1 ,1 ,0〉平行于轧向 ,位向密度沿纤维轴从 {0 0 1 }〈1 - 1 0〉到 {1 1 1 }〈1 - 1 0〉扩展 ,在位向 {0 0 1 }〈1 - 1 0〉附近 ,获得最大位向密度为 2 6.9.Cu Zn Al合金马氏体有 1 0个主要的织构组元 .从奥氏体与马氏体的织构分析发现 ,两者织构是相互关联的 ,一个奥氏体的织构组元对应多个马氏体的织构组元 ,此结果符合马氏体形成自相适应形貌的要求 .

Formation of mesophase microbeads from bulk mesophase pitch induced by fullerene

A transformation of naphthalene-based coalescenced mesophase pitch(NMP)to mesophase microbeads was achieved by heating a mixture of NMP and fullerene(C_(60)).This is different from the conventional process of the liquid-phase carbonization of isotropic pitch to the emergence of carbon microbeads in the matrix and finally their growth to form a 100%anisotropic bulk meso-phase,but rather a reverse transformation.The effects of C_(60) loading and reaction temperature on the morphological transformation of mesophase were investigated by polarizing optical and scanning electron microscopies.The physical changes in the NMP induced by C_(60) were characterized by thermogravimetric analysis,Fourier transform infrared spectroscopy,X-ray diffractometry and Raman spectroscopy.The results show that the coalesced NMP can be converted to a spherical type at 300-320℃ with the addition of 5%C_(60),and the size of the mesophase microbeads increases with increasing temperature.Furthermore,a model is established to ex-plain the unique induction effect of C_(60) in the transformation process.This work makes the morphological transformation of MP con-trollable,and provides a new idea for the understanding and research of mesophase pitch.

纳米双相钕铁硼永磁合金的织构及磁畴

为开发纳米复合永磁材料高磁能积的潜力,用熔体快淬法制备各向异性的纳米双相快淬带。X光衍射结果表明,Nd9Fe85-xNbxB6(x=0,0.5,1.0)快淬带中存在垂直于带面的Nd2Fe14B[00L]织构,其自由面上的织构强于贴辊面。x=1.0时,在15m.s-1的快淬速度下的择优取向度为94%。磁力显微镜观察表明晶粒间存在强烈的交换耦合作用。x=0.5时的快淬带具有较强交换耦合作用及高织构度,因此具有最佳磁性能。其剩余磁极化强度为1.130T,内禀矫顽力为519.8kA.m-1,最大磁能积为121.2kJ.m-3。

Effect of forging on the microstructure and texture of a high Nb containing γ-TiAl alloy

The effect of forging on the microstructure and texture evolution of a high Nb containing Ti-45Al-7Nb-0.3W(at.%)alloy was investigated by X-ray diffractometer(XRD),scanning electron microscopy(SEM),and transmission electron microscopy(TEM).The results show that the as-cast alloy is mainly composed of α_(2)/γ lamellar colonies with a mean size of 70μm,but the hot-forged pancake displays a near duplex microstructure(DP).Kinking and bending of lamellar colonies,deformation twinning and dynamic recrystallization(DRX)occur during hot forging.Meanwhile,dense dislocations in theβphase after forging suggest that the high-temperature β phase with a disordered structure is favorable for improving the hot-workability of the alloy.Unlike the common TiAl casting texture,the solidification process of the investigated as-cast alloy with high Nb content is completely via the β phase region,resulting in the formation of a<110>γ fiber texture where the<110>γ aligns parallel to the heat-flow direction.In comparison,the relatively strong<001>and weak<302>texture components in the as-forged alloy are attributed to the deformation twinning.After annealing,static recrystallization occurs at the twin boundary and intersections,which weakens the deformation texture.

一种组合型液晶聚酰亚胺性能的研究

以 3 ,5 二氨基苯甲酸 4′ 联苯酯和 4,4′ 二氨基联苯等为共聚单体 ,制备了一种主、侧链均含联苯液晶基元的组合型液晶聚酰亚胺 (PI)。DSC、WAXD和热台偏光显微镜分析表明该组合型液晶聚酰亚胺呈现层状近晶相织构。主、侧链液晶基元间的原位复合自增强作用使PI 3薄膜的力学强度提高了10 7% ,模量提高了 12 9% ,尺寸稳定性提高了 40 .6%。共聚和侧链液晶基元的引入改善了PI的成膜加工性能 ,所形成的组合型液晶PI能溶解于常用极性有机溶剂如NMP、DMAc和DMSO中。

Microstructure and texture evolution during high-strain-rate superplastic deformation of coarse-grained Mg-Gd-Y-Zr rolled sheet

Microstructure and texture evolution during high-strain-rate superplastic deformation of the rolled Mg-Gd-Y-Zr sheet were investigated.The tensile tests at the strain rate of 0.01 s-1 achieved the elongations of 180%-266% in the deformation temperature range of 400-500 ℃.Post-deforming microstructures were characterized by optical microscopy,scanning electron microscopy and transmission electron microscopy,while crystallographic orientation information was obtained from macro-texture analysis.The results show that the high strain-rate superplasticity was attributed to class-I dislocation creep accommodated by dynamic recrystallization （DRX）.During preheating at 435 ℃ for 600 s,twinning-induced recrystallization occurred.The initial strain of 80% made original grains fragmented and produced homogenous DRX grains.The interaction between dynamic recrystallization and dynamic precipitation yielded out such a phenomenon that finer DRX grains were often accompanied by denser particles.The macro-texture evolution exhibited some characteristics of the crystal rotation arising from basal slip and prismatic slip despite the occurrence of DRX.

Interaction among deformation, recrystallization and phase transformation of TA2 pure titanium during hot compression

TA2 pure titanium was chosen to research the interaction among deformation, recrystallization and phase transformation during hot compression. The samples were hot compressed by thermal simulation method with different processing parameters. Variant selection induced by stress during cooling after compression was found. The prismatical texture component which featured that the [0001] direction perpendicular to the compressing direction produced preferentially under the compressing stress. As a result, the transformedα phase possesses strong prismatical texture which is different with the basal texture of compressed αphase. The minimum elastic strain energy is demonstrated to be the main reason that causes the variant selection. Dynamic recrystallization behavior and microstructure evolution during hot compression were also studied.

Compressive anisotropy of extruded Mg-Dy-Zn alloy sheet

Compressive anisotropy of extruded Mg-2Dy-0.5Zn （mole fraction, %） alloy sheet was investigated. The alloy sheet was mainly composed ofα-Mg, （Mg, Zn）xDy phase and a large number of long period stacking ordered （LPSO） phases distributed along the extrusion direction. The compressive experimental results show that the alloy sheet exhibits an obvious compressive anisotropy. The compressive strength of the specimen in the extrusion direction （ED） is higher than those of the specimens in the transverse direction （TD） and 45° inclined to the extrusion direction. The compressive yield strength （CYS）, ultimate compressive strength （UCS） and compressive strain of the specimen in the ED are 274.65 MPa, 518.94 MPa and 12.93%, respectively. The compressive anisotropy is mainly attributed to the distribution of LPSO phase and formation of〈10 10〉//ED fiber texture in the deformed grains.

环己烷类聚硅氧烷侧链液晶的合成与液晶行为研究

选用环己烷类液晶基元反式-4-乙烯基-反式-4’-丙基双环己烷（MA）和反式-4-丁烯基-反式-4’-丙基双环己烷（MB）,通过硅氢加成反应将其接枝到柔性的聚硅氧烷主链上,合成了含有2种环己烷结构的聚硅氧烷侧链液晶P_（AB）,产率为80.3%。采用傅立叶变换红外光谱法（FTIR）和氢核磁共振谱法（~1H-NMR）对其分子结构进行表征,说明其分子结构符合预期;采用热台偏光显微镜法（POM）和X射线衍射法（XRD）对其液晶相类型和液晶行为进行观察和分析,发现在升降温过程中所呈现出胆甾相油状条纹织构和小板块织构,揭示出因有序度不同所导致的不同织构特征;采用差示扫描量热法（DSC）和综合热分析法（TGA）对其热性能进行分析,确定其液晶区间为28.68K,T_（d（5wt%））为405.25℃,均高于液晶基元的液晶区间和热稳定性。

Microstructure and mechanical properties of Mg-Gd-Y-Zr alloy processed by equal channel angular pressing

Microstructure evolution and texture development and their effects on mechanical properties of a Mg-Gd-Y-Zr alloy during equal channel angular pressing（ECAP） were investigated.It is found that the microstructure is still inhomogeneous after four passes,and two zones,namely the fine grain zone（FGZ） and the coarse grain zone（CGZ） are formed.The grain refinement occurs mainly by particle-stimulated nucleation（PSN） mechanism,which led to a more random texture after four passes of ECAP.In the ECAP-processed alloy,the strength did not increase while the ductility was enhanced dramatically compared with the as-received condition.The change of ductility of this alloy was discussed in terms of texture and second phase particles.

Preparation and mechanical properties of carbon/carbon composites with high textured pyrolytic carbon matrix

Short carbon fiber felts with an initial porosity of 89.5% were deposited by isobaric, isothermal chemical vapor infiltration using natural gas as carbon source. The bulk density of the deposited carbon/carbon （C/C） composites was 1.89 g/cm3 after depositing for 150 h. The microstructure and mechanical properties of the C/C composites were studied by polarized light microscopy, X-ray diffraction, scanning electron microscopy and three-point bending test. The results reveal that high textured pyrolytic carbon is deposited as the matrix of the composites, whose crystalline thickness and graphitization degree highly increase after heat treatment. A distinct decrease of the flexural strength and modulus accompanied by the increase of the toughness of the C/C composites is found to be correlated with the structural changes in the composites during the heat treatment process.

Morphology and chemical composition of γ/γ' phases in Re-containing Ni-based single crystal superalloy during two-step aging

The γ/γ＇ microstructure of a Re-containing Ni-based single crystal super alloy after a two-step aging was studied using scanning electron microscopy （SEM）,transmission electron microscopy （TEM） and scanning transmission electron microscopy （STEM）.The crystals were grown by the floating zone （FZ） method.Both cuboidal and spherical γ＇ precipitates were formed after a two-step aging.The size of the cuboidal γ＇ phases first increased and then decreased with the extension of the second-step aging time.Re,Co and Cr strongly concentrated in the γ phase whereas Ni and Al enriched in the γ＇ phase.Thermodynamic calculation by JMatPro was performed to explain the experimental observations.

Magnetostriction and microstructure of melt-spun Fe_(77)Ga_(23) ribbons prepared with different wheel velocities

A set of stacked ribbons with the composition of Fe77Ga23 were prepared with different wheel velocities of 7 m/s, 12.5 m/s and 25 m/s（named as S7, S12.5 and S25, respectively）. High resolution X-ray diffraction patterns of these ribbons show that all the ribbons present the disordered A2 structure, whereas an additional modified-DO3 phase is detected in S12.5 and S25. S25 has stronger（100） texture than other two samples. Ga K-edge extended X-ray absorption fine structure results indicate that both bond distance and the number of Ga atoms in the second neighbor shell around Ga decrease with increasing wheel velocity. No Ga cluster is detected in the studied ribbons. A short-range ordering Ga-rich phase and large local strain have no obvious influence on magnetostriction of S7. It is believed that both the（100） texture and the additional modified-DO3 phase play a positive role in magnetostrictive properties of Fe77Ga23 ribbons.

Effects of microstructure on tensile properties of AA2050-T84 Al−Li alloy

The effect of microstructure evolution on the tensile properties of 2050 Al-Li alloy thick plate aged at 150 ℃ with 80 mm in thickness(t) was studied from a microstructural perspective. Scanning electron microscope, optical microscope, transmission electron microscope and X-ray diffractometer were used to explore the surface(t/6), interlayer(t/3) and center(t/2) thickness layer of this alloy. Results show that the secondary phases on grain boundaries, precipitates and textures vary depending on the thickness location. The precipitation strengthening has a stronger influence on the alloy along the rolling direction than the transverse direction from the under-aged to the peak-aging condition;however, its effect on the anisotropy is insignificant. The higher Taylor factor(M) value caused by stronger β fiber rolling textures and the intergranular phases is the main reason that leads to the highest strength at the t/2 position along the rolling direction. The M-value has a limited change at different thickness layers along the transverse direction, which causes the same tensile strength.

Stress-induced martensite phase transformation of FeMnSiCrNi shape memory alloy subjected to mechanical vibrating polishing

Fe66Mn15Si5Cr9Ni5(wt.%)shape memory alloy(SMA)withγaustenite andεmartensite was subjected to mechanical vibrating polishing and consequently its surface suffered from plastic deformation in the case of compressive stress.Almost completeεmartensite transformation is found to occur in FeMnSiCrNi sample subjected to mechanical vibrating polishing,where stress-induced martensite transformation plays a predominant role.Stressinduced martensite transformation of FeMnSiCrNi SMA is closely related to the orientation of external stress.The complicated compressive stress which results from the mechanical vibrating polishing contributes toεmartensite transformation fromγaustenite of FeMnSiCrNi SMA.Mechanical vibrating polishing has a certain influence on the surface texture ofεmartensite of FeMnSiCrNi SMA,where■<0001>texture appears in the polished FeMnSiCrNi SMA.

Strength and structure variation of 2195 Al-Li alloy caused by different deformation processes of hot extrusion and cold-rolling

2195 Al-Li alloy was deformed through extrusion followed by cold-rolling.The textures of the extruded plate and cold-rolled sheet after solutionization were investigated.The longitudinal strength and precipitates after T8 aging were measured and observed,respectively.Compared to those in the sheet,T1(Al2 Cu Li)precipitates in the extruded plate after T8 aging are non-uniform,and their incubation time is shorter.The extruded plate after solutionization is not recrystallized and contains 55.28%deformation textures of Brass and S.In the cold-rolled sheet after solutionization,massive recrystallization occurs and S component disappears.Due to the higher fraction of Brass and S textures with higher Schmid factor and lower equivalent sliding system number,the extruded plate possesses an yield strength not higher or even lower,but a tensile strength higher,than the cold-rolled sheet after solutionization.In addition,during the aging after pre-stretch,these textures promote T1 precipitation on preferred sliding planes of cold-rolled sheet and cause its higher yield strength and tensile strength after T8 aging.

Isothermal annealing of cold-rolled Al-Mn-Fe-Si alloy with different microchemistry states

Microstructural evolution of a cold-rolled Al-Mn-Fe-Si alloy during annealing was studied. Except the as-cast variant, two other different homogenizations were considered, one gave a high density of fine dispersiods providing a considerable Zener drag influencing the softening behavior while the other gave a lower density of coarser dispersoid structure providing a much smaller drag effect. The gradual microstructural evolutions during annealing for the three variants were captured by interrupting annealing at different time. Effects of microchemistry state on recrystallization kinetics, recrystallized grain structure and texture were characterized by EBSD. It is demonstrated that the actual softening kinetics, final microstructure and texture are a result of delicate balance between processing condition and microchemistry state. Strong concurrent precipitation takes place in the case with high concentration of Mn in solid solution, which suppresses nucleation and retards recrystallization and finally leads to grain structure of coarse elongated grains dominated by a P texture component together with a ND-rotated cube component. On the contrary, when solute content of Mn is low and pre-existing dispersoids are relatively coarser, faster recrystallization kinetics is exhibited together with an equiaxed grain structure with mainly cube texture.

Microstructure and photocatalytic activity of Ni-doped ZnS nanorods prepared by hydrothermal method

Pure ZnS and Ni^2+-doped ZnS nanorods (Zn1-xNixS, x=0, 0.01, 0.03, 0.05 and 0.07, mole fraction,%) were synthesized by hydrothermal method. The effects of Ni2+ doping on the phase-structure, morphology, elemental composition and optical properties of the samples were investigated by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), X-ray energy dispersive spectrometry (EDS) and ultraviolet–visible spectroscopy (UV-Vis), respectively. The photocatalytic activity of Zn1-xNixS nanorods was evaluated by the photodegradation of organic dyes Rhodamine B (RhB) in aqueous solution under UV light irradiation. The results show that all samples exhibit wurtzite structure with good crystallization. The morphologies are one-dimensional nanorods with good dispersion, and the distortion of the lattice constant occurs. The band gap of Zn1-xNixS samples is smaller than that of pure ZnS, thus red shift occurs. Ni^2+-doped ZnS nanocrystals can enhance photocatalytic activities for the photodegradation of RhB. Especially, Zn0.97Ni0.03S sample exhibits better photocatalytic performance and photocatalytic stability for the decomposition of RhB.

Sol-gel auto-combustion synthesis of K_xNa_(1-x)NbO_3 nanopowders and ceramics: Dielectric and piezoelectric properties

The KxNa1-xNbO3 nanopowders with cubic-like morphology and an average size of about 50 nm were synthesized by sol-gel auto-combustion method.And then,the ceramics were prepared and the phase transition,microstructure and electrical properties of the KxNa1-xNbO3 ceramics were investigated.Pure perovskite phases of the KxNa1-xNbO3 ceramics were confirmed by XRD patterns and the K0.50Na0.50NbO3 ceramics show the coexistence of orthorhombic and monoclinic structures.SEM micrographs show that all samples have bimodal grain size distributions and the number of the small grains decrease with increasing K+content in the bimodal grain size distribution system.The K0.50Na0.50NbO3 ceramics with the uniform grain size and the maximum density show excellent electrical properties withεr=467.40,tanδ=0.020,d33=128 pC/N and kp=0.32 at the room temperature,demonstrating that the properties of the K0.50Na0.50NbO3 powers prepared by sol-gel auto-combustion are excellent and the ceramics are promising lead-free piezoelectric materials.

The Role of Storytelling in Personal Knowledge Convey

The relative difficulty of capturing and conveying knowledge is determined on the diversity of knowledge types. It is necessary to interpret the consciously capturing process of the knowledge that is formed unconsciously. Storytelling is important in the capturing and conveying of tacit knowledge. Culture, structure, system, and the knowledge holders within the organization also affect the transfer of personal knowledge. The company M, has successfully created knowledge based on transfer of personal knowledge by leveraging the organization mechanism ＂The board of advisors＂. In order to elucidate the process, the author analyzed the recordings of the passing on contents using the protocol analysis.