相间力对微孔通道内两相驱替渗流影响规律的LBM研究

为研究了相间力对微孔通道内水-气两相渗流规律的影响,利用格子-Boltzmann方法建立了孔隙尺度下微孔通道内的水-气两相渗流驱替的数学模型。采用C++语言编制的程序对微孔通道内水-气两相渗流驱替过程进行了数值模拟。通过对模拟结果的分析发现:两相驱替的总体效果与相间力有较大关系,流固作用力越大,多孔骨架的亲水性越强,两相渗流的总体驱替效果就越好,驱替速度越大,反之亦然。

基于竖直圆管空气-水两相流实验的相间曳力模型研究

研究两相流相间阻力特性对系统程序关键本构模型封闭具有重要意义。本文基于竖直圆管开展了空气-水两相流实验,采用四探头电导探针对空泡份额、气泡弦长和界面面积浓度等气泡参数的径向分布进行了测量。结果表明空泡份额和气泡弦长呈现“核峰型”分布,而界面面积浓度并没有表现出随流速的单调关系。进一步开发了泡状流和弹状流的相间曳力模型,考虑了液相表观流速与管径对气泡尺寸分布的影响,建立了临界韦伯数与不同液相流速的关系。计算得到的空泡份额和界面面积浓度与实验数据整体符合较好,验证了模型的可靠性,为两相流相间阻力特性研究提供参考意义。

推导悬浮体二相流基本方程的一种新方法

本文提出了一种从基本守恒原理出发,经过数学推导,得到悬浮体二相流基本方程的新方法。由于这组方程形式简单,而且其中各量都有简明的物理意义,因此易于被人们理解和接受,也更接近实用。

基于欧拉-欧拉方法的气液两相流数值模型发展综述

深海油气多相混输系统内部油气混输本质上是一种高压高含气率的气液两相流问题。现如今多采用欧拉-欧拉方法对该问题进行数值研究,然而该方法的准确性依赖于相间力模型与群体平衡子模型的构建与选择。因此,本文对现有的相间力模型进行了总结,主要包括曳力、升力、壁面润滑力、湍流扩散力、虚拟质量力,并对相关模型的理论与发展进行了阐述,总结了压力以及高含气率下泡群对相间力模型的修正方法。此外,考虑到高含气率工况下气泡与气泡之间的相互作用,针对气泡群体平衡模型进行介绍,对气泡的破碎与聚并模型进行了梳理,总结了高压情况下群体平衡模型的修正思路。以期对深海高压高含气率环境下的气液混输模拟计算提供借鉴。

鼓泡流化床内颗粒分离行为模拟研究

颗粒-颗粒相间曳力是影响鼓泡流化床流体动力行为的重要因素之一。本文基于欧拉-欧拉双流体气固两相流模型,采用考虑了颗粒分离斜度系数的颗粒-颗粒相间曳力模型,对床内具有两种不同颗粒尺寸、底部均匀布风的鼓泡流化床进行了数值模拟研究,并将模拟结果与Owoyemi等的实验及数值模拟结果进行了比较。研究结果表明考虑颗粒分离斜度系数的颗粒-颗粒相间曳力模型合理地预测和分析了床内颗粒分离等特性。

Flow equation and similarity criterion during centrifugal casting in micro-channel

Liquid metal filling flow process in the microscale during the centrifugal casting process was studied by means of similar physical simulation. The research was focused on derived similarity criterion. Based on the traditional flow equations, the flow equation and the Bernoulli＇s equation for liquid metal flows in micro-scale space were derived, which provides a mathematical model for numerical simulation of micro-scale flow. In the meanwhile, according to the micro-flow equation and the similarity theory, the similarity criterion for the physical simulation of the mold filling behaviors was presented under centrifugal force field, so as to achieve the visual observation and quantitative analysis of micro-flow process.

WC-Ni_3Al-B composites prepared through Ni+Al elemental powder route

In order to develop the liquid phase sintering process of WC-Ni3Al-B composites,the preparation process of WC＋Ni3Al prealloyed powder by reaction synthesis of carbonyl Ni,analytical purity Al and coarse WC powders was investigated.DSC and XRD were adopted to study the procedure of phase transformation for the 3Ni＋Al and 70%WC＋（3Ni＋Al） mixed powders in temperature ranges of 550-1200 °C and 25-1400 °C,respectively.The results demonstrate that the formation mechanism of Ni3Al depends on the reaction temperature.Besides WC phase,there exist Ni2Al3,NiAl and Ni3Al intermetallics in the powder mixture after heat treatment at 200-660 °C,while only NiAl and Ni3Al exist at 660-1100 °C.Homogeneous WC＋Ni3Al powder mixture can be obtained in the temperature range of 1100-1200 °C.The WC-30%（Ni3Al-B） composites prepared from the mixed powders by conventional powder metallurgy technology show nearly full density and the shape of WC is round.WC-30%（Ni3Al-B） composites exhibit higher hardness of 9.7 GPa,inferior bending strength of 1800 MPa and similar fracture toughness of 18 MPa-m1/2 compared with commercial cemented carbides YGR45（WC-30%（Co-Ni-Cr））.

Microstructure and mechanical properties of high strength Al-Zn-Mg-Cu alloys used for oil drill pipes

Three Al?Zn?Mg?Cu alloys used for oil drill pipes (Alloy A: Al?6.9Zn?2.3Mg?1.7Cu?0.3Mn?0.17Cr; Alloy B: Al?8.0Zn?2.3Mg?2.6Cu?0.2Zr, Alloy C: Al?8.0Zn?2.3Mg?1.8Cu?0.18Zr) were studied by hardness tests, tensile tests and transmission electron microscopy (TEM). The results show that the ultimate tensile strength, yield strength and elongation for Alloys A, B and C are 736 MPa, 695.5 MPa and 7%; 711 MPa, 674 MPa and 12.5%; 740.5 MPa, 707.5 MPa and 13%, respectively after solid solution treatment ((450 °C, 2 h)+(470 °C, 1 h)) followed by aging at 120 °C for 12 h. The dominant strengthening phases in Alloy A are GPII zone andη′ phase, the main precipitate in Alloy B isη′ phase, and the main precipitates in Alloy C are GPI zone, GPII zone andη′ phase, which are the reason for better comprehensive properties of Alloy C. The increase of zinc content leads to the improvement of the strength. The increase of copper content improves the elongation but slightly decreases the strength. Large second-phase particles formed by the increase in the manganese content induce a decrease in the elongation of alloys.

Icon memory research under different time pressures and icon quantities based on event-related potential

In order to obtain related brain electrical components and neural bases of physiology assessment of icon elements in a digital human-computer interface the modified sample-delay matching task experimental paradigm is used under different time pressures 4 000 and 2 000 ms and different icon quantities three five and ten icons on icon memory based on event-related potential ERP technology.Experimental results demonstrate that P300 has significant volatility changes and the maximum amplitude around the middle line of the parietal area PZ and P200 has obvious volatility changes around the middle line of the frontal and central area FCZ during icon cognition.P300 and P200 amplitudes increase as tasks become more difficult.Thus P300 latency is positively correlated with task difficulty. ERP research on the characteristics of icon memory will be an important reference standard in guiding user neurocognitive behavior and physiology assessment on interface usability.

基于颗粒相间曳力模型的鼓泡流化床流动特性数值模拟

基于欧拉-欧拉双流体气固两相流模型,数值模拟研究了床内具有两种不同颗粒尺寸、底部均匀布风的鼓泡流化床气固两相流体动力特性。采用颗粒-颗粒相间曳力模型,考察了大颗粒及小颗粒的分离情况。研究结果表明考虑颗粒-颗粒相间曳力模型,气体能够充分地与固体颗粒发生相互作用,表明在数值模拟中考虑颗粒-颗粒相间曳力模型可以更合理地预测床内气固两相流动特性。

EFFECT OF DUMP GAP ON TOTAL PRESSURE LOSS IN DUMP DIFFUSER

The dump diffuser is an important component in advanced annular combustor, and its performance affects greatly the fluid field and pressure loss of the combustor. This paper presents the characteristics of the total pressure loss. Experiments and numerical simulations, keeping the inlet March number of prediffuser constant ( Ma =0 20), are carried out to obtain the regularity of the total pressure loss. It varies with the relative dump gap ( δ =1 2～3 0)by changing the position of prediffuser and combustor liner, respectively. Research shows that there exists the minimum total pressure loss ( σ *=1 6%～1 75%) when relative dump gap δ is about 1 8.

Effect of Sr content on microstructure and mechanical properties of Mg-Li-Al-Mn alloy

The as-cast Mg-8Li-3Al-0.5Mn-xSr（LAM830-xSr, x=0-1.0） alloys were designed and prepared in a vacuum induction furnace under controlled argon atmosphere. The alloys were then processed by hot extrusion, and their microstructural evolution and mechanical properties were analyzed. Results indicate that the LAM830 alloy mainly consists of α-Mg, β-Li, Al2Mn3, and LiMgAl2 phases. Sr addition results in the precipitation of Al-Sr. Moreover, Sr addition results in a fact that the secondary dendrite arm spacing（DAS） of the primary α-Mg phase is obvious refined. Microstructure of the investigated alloys is further refined as a result of the hot extrusion treatment. The content and morphology of the secondary phases have important effects on the mechanical properties of the alloys. The as-extruded LAM830-0.5Sr alloy exhibits an optimal elongation of 22.43% and as-extruded LAM830-0.75 Sr alloy shows an optimal tensile strength of 265.46 MPa.

基于TPTF的高压水平分层流实验数据对Relap5/Mod3.2的改进

基于Relap5/Mod3.2程序计算结果与日本的两相流试验装置(TPTF)实验数据进行比较,显示出Relap5程序在计算水平管道分层流的空泡份额分布方面,与实验数据有一定偏差。分析认为,Relap5程序在水平分层流的过渡区域及过渡区域相间曳力公式的设置上存在问题,导致程序错误地将部分水平分层流工况预测为其他流型。在修改过渡流型判定准则及过渡流型平均公式后,新的计算结果表明:采用本文修改后的计算结果能更好地与实验结果相符合。

pH-dependent leaching mechanism of carbonatitic chalcopyrite in ferric sulfate solution

The dissolution of a carbonatitic chalcopyrite(CuFeS2)was studied in H_(2)SO_(4)−Fe_(2)(SO_(4))_(3)−FeSO_(4)−H_(2)O at varying pH values(0.5−2.5)and 25℃ for 12 h.Experiments were conducted with a size fraction of 53−75μm.Low Cu recoveries,below 15%,were observed in all pH regimes.The results from the XRD,SEM−EDS,and optical microscopic(OM)analyses of the residues indicated that the dissolution proceeded through the formation of transient phases.Cu_(3.39)Fe_(0.61)S_(4) and Cu_(2)S were the intermediate phases at pH 0.5 and 1.0,respectively,whereas Cu_(5)FeS_(4) was the major mineral at pH 1.5 and 1.8.The thermodynamic modelling predicted the sequential formation of CuFeS_(2)→Cu_(5)FeS_(4)→Cu_(2)S→CuS.The soluble intermediates were Cu_(5)FeS_(4) and Cu2S,whilst,CuS and Cu_(3.39)Fe_(0.61)S_(4) were the refractory phases,supporting their cumulating behaviour throughout the dissolution.The obtained results suggest that the formation of CuS and Cu_(3.39)Fe_(0.61)S_(4) could contribute to the passive film formed during CuFeS_(2) leaching.

Pressure from surrounding rock of three shallow tunnels with large section and small spacing

With the increasing traffic demand, the closely built three or more tunnels with large section play a significant role in the tunnel construction. However, the interaction among tunnels has important influences on the security and economy of tunnel engineering, and the calculation of pressure from the surrounding rock during the excavation is one of the problems that need to be solved urgently. Based on the practical engineering of three tunnels, the load model of three tunnels was proposed in consideration of the interaction and excavation sequence between tunnels. In comparison with the load model of single tunnel, the construction mechanical characteristics of the three tunnels were analyzed. The results show that the rock pressure of three tunnels calculated by the current tunnel design code is not reliable, and the interaction force increases with the spacing between tunnels.

Intermolecular Interactions in Self-Assembly Process of Sodium Dodecyl Sulfate by Vertically Polarized Raman Spectra

Molecular self-assembly is extremely important in many fields, but the characterization of their corresponding intermolecular interactions is still lacking. The C-H stretching Raman band can reflect the hydrophobic interactions during the self-assembly process of sodium dodecyl sulfate （SDS） in aqueous solutions. However, the Raman spectra in this region are seriously overlapped by the OH stretching band of water. In this work, vertically polarized Raman spectra were used to improve the detection sensitivity of spectra of C-H region for the first time. The spectral results showed that the first critical micelle concentration and the second critical micelle concentration of SDS in water were 8.5 and 69 mmol/L, respectively, which were consistent with the results given by surface tension measurements. Because of the high sensitivity of vertically polarized Raman spectra, the critical micelle concentration of SDS in a relatively high concentration of salt solution could be obtained in our experiment. The two critical concentrations of SDS in 100 mmol/L NaCl solution were recorded to be 1.8 and 16.5 mmol/L, respectively. Through comparing the spectra and surface tension of SDS in water and in NaCl solution, the self-assembly process in bulk phase and at interface were discussed. The interactions among salt ions, SDS and water molecules were also analyzed. These results demonstrated the vertically polarized Raman spectra could be employed to study the self-assembly process of SDS in water.

Understanding visual-auditory correlation from heterogeneous features for cross-media retrieval

Cross-media retrieval is an interesting research topic,which seeks to remove the barriers among different modalities.To enable cross-media retrieval,it is needed to find the correlation measures between heterogeneous low-level features and to judge the semantic similarity.This paper presents a novel approach to learn cross-media correlation between visual features and auditory features for image-audio retrieval.A semi-supervised correlation preserving mapping(SSCPM)method is described to construct the isomorphic SSCPM subspace where canonical correlations between the original visual and auditory features are further preserved.Subspace optimization algorithm is proposed to improve the local image cluster and audio cluster quality in an interactive way.A unique relevance feedback strategy is developed to update the knowledge of cross-media correlation by learning from user behaviors,so retrieval performance is enhanced in a progressive manner.Experimental results show that the performance of our approach is effective.

Ruppeiner Geometry of (2+l)-Dimensional Spinning Dilaton Black Hole

In this paper, we study the geometrothermodynamics of （2 ＋ 1）-dimensional spinning dilaton black hole. We show that the Ruppeiner curvature vanishes, which implies that there exist no phase transitions and thermodynamic interactions. However when the thermodynamics fluctuation is included, the geometry structure is reconsidered. The non-vanishing Ruppeiner curvature is obtained, which means the phase space is non-flat. We also study the phase transitions and show that it can indeed take D/ace at some points.

Black Hole Complementary Principle and Noncommutative Membrane

In the spirit of black hole complementary principle, we have found the noncommutative membrane of Scharzchild black holes. In this paper we extend our results to Kerr black hole and see the same story. Also we make a conjecture that spacetimes are noncommutative on the stretched membrane of the more general Kerr-Newman black hole.

Perturbation to Noether-Lie Symmetry and Adiabatic Invariants for Mechanical Systems in Phase Space

Based on the concept of adiabatic invariant,the perturbation to Noether-Lie symmetry and adiabatic invariants for mechanical systems in phase space are studied.The criterion of the Noether-Lie symmetry for the perturbed system is given,and the definition of the perturbation to Noether-Lie symmetry for the system under the action of small disturbance is presented.Meanwhile,the Noether adiabatic invariants and the generalized Hojman adiabatic invariants of the perturbed system are obtained.