本文给出了使生灭过程{X(t),t≥0}有真分布的充分条件与必要条件,所谓真分布即 sum i=0 to ∞ p_1(t)=1,其中 p_1(t)=P(X(t)=i),所获得的结果与[1]、[5]的主要区别在于所有条件都是加在生灭系数之和之上的,且特别强调了生灭微分方程解...本文给出了使生灭过程{X(t),t≥0}有真分布的充分条件与必要条件,所谓真分布即 sum i=0 to ∞ p_1(t)=1,其中 p_1(t)=P(X(t)=i),所获得的结果与[1]、[5]的主要区别在于所有条件都是加在生灭系数之和之上的,且特别强调了生灭微分方程解的唯一性的至关重要性,此外在较宽松的条件下彻底推广了Feller-Lundberg 定理。展开更多
In order to study the thermoelectric efficiency of microwave heating and reproduction of asphalt pavements and the uniformity of reproduction temperature distribution, a waveguide excitation cavity is designed and app...In order to study the thermoelectric efficiency of microwave heating and reproduction of asphalt pavements and the uniformity of reproduction temperature distribution, a waveguide excitation cavity is designed and applied to the structural design of a microwave heater. The structural sizes of the incentive cavities are determined based on the waveguide transmission line theory. Using IE3D software, electromagnetic simulations are respectively carried out in four different situations, including the distances between the magnetron probes （antennas） and a short-circuit board, different horn electric lengths and aperture sizes, different dielectric properties of the asphalt mixture, and the distances between the asphalt surface and the mouth cavity. The results show that, when the distance between the magnetron probe and the short-circuit board is 32.5 ram, it is the best installation site; reduction of aerial length is the main factor in improving the heating uniformity. When the aggregate is limestone, the best heating effect can be produced. Maximum radiation efficiency can be realized by adjusting the space between the heater radiation port and the asphalt pavement. The experimental results of asphalt mixture heating in four different situations have a substantial agreement with the simulation results, which confirms that the developed microwave heater can achieve better impedance matching, thus improving the quality and efficiency of heating regeneration.展开更多
An attempt has been made to develop a distributed software infrastructure model for onboard data fusion system simulation, which is also applied to netted radar systems, onboard distributed detection systems and advan...An attempt has been made to develop a distributed software infrastructure model for onboard data fusion system simulation, which is also applied to netted radar systems, onboard distributed detection systems and advanced C3I systems. Two architectures are provided and verified: one is based on pure TCP/IP protocol and C/S model, and implemented with Winsock, the other is based on CORBA (common object request broker architecture). The performance of data fusion simulation system, i.e. reliability, flexibility and scalability, is improved and enhanced by two models. The study of them makes valuable explore on incorporating the distributed computation concepts into radar system simulation techniques.展开更多
Based on the character of the modular self-reconfigurable （MSR） robot, a novel homogeneous and lattice MSR robot, M-Cubes, was designed. Each module unit of the robot has 12 freedoms and is composed of six rotary jo...Based on the character of the modular self-reconfigurable （MSR） robot, a novel homogeneous and lattice MSR robot, M-Cubes, was designed. Each module unit of the robot has 12 freedoms and is composed of six rotary joints and one cubic link. An attached/detached mechanism was designed on the rotary joints. A novel space transmitting system was placed on the inner portion of the cubic link. A motor separately transmitted torque to the six joints which were distributed equally on six surfaces of the cubic link. The example of a basic motion for the module was demonstrated. The result shows that the robot is concise and compact in structure, highly efficient in transmission, credible in connecting, and simple in controlling. At the same time, a simulator is developed to graphically design the system configuration, the reconfiguration process and the motion of cluster modules. The character of local action for the cellular automata （CA） is utilized. Each module is simplified as a cell. The transition rules of the CA are developed to combine with the genetic algorithm （GA） and applied to each module to accomplish distributed control. Simulation proves that the method is effective and feasible.展开更多
Based on MATRIXx, a universal real-time visual distributed simulation system is developed. The system can receive different input data from network or local terminal. Application models in the simulation modules can a...Based on MATRIXx, a universal real-time visual distributed simulation system is developed. The system can receive different input data from network or local terminal. Application models in the simulation modules can automatically get such data to be analyzed and calculated, and then produce real-time simulation control information. Meanwhile, this paper designs relevant simulation components to implement the input and output data, which can guarantee the real-time and universal of the data transmission. Result of the experimental system shows that the real-time performance of the simulation is perfect.展开更多
The development process as well as the core theory of distributed interactive simulation and high level architecture are discussed, and combined with graphics features, a system of real time distributed visual simula...The development process as well as the core theory of distributed interactive simulation and high level architecture are discussed, and combined with graphics features, a system of real time distributed visual simulation is established. Based on computer network, simulation platform is built by installing related software and modeling object, and the interactive functions are extended by programming. A set of solutions for building a distributed visual simulation system that include both hardware and software are put forward, and a practical instance is also provided. The whole building process can be summarized into two steps that are scheme consideration and system realization.展开更多
A unified model which is used to study the launching and travelling dynamic properties of a rlcket/launcher system is established. In this model, the rocket, the launcher,and the launching vehicle are considered as a...A unified model which is used to study the launching and travelling dynamic properties of a rlcket/launcher system is established. In this model, the rocket, the launcher,and the launching vehicle are considered as an interacting dynamic system in order to study the dynamic interaction between the various parts of the system and the optimal parameter matching among the above mentioned parts. The following random factors are taken into account in this paper. road surface excitation. rocket mass center misalignment, thrust misalignment, dynamic of the rocket, and the cross wind. Based on this unified model, a computer simulation software is developed, some simulation work has been carried out, and certain beneficial results have been achieved.展开更多
A new seabed sediment fidelity sampler was developed and its thermal insulation performance was studied and analyzed. The temperature distribution simulation indicated that the sample quality could be insured by using...A new seabed sediment fidelity sampler was developed and its thermal insulation performance was studied and analyzed. The temperature distribution simulation indicated that the sample quality could be insured by using this new sampler. Based on ANSYS10, the temperature finite element model of the sample cylinder was established. According to the law of conservation of energy, the unsteady heat transmit equation of the sampler under solid-liquid coupling condition was derived, then the mathematical model calculation was carried out by using a mixed finite-element finite-difference method, and two thermal insulation methods were used. The simulation was carried out by using the thickness of the thermal insulation layer and heat conductivity as the variable parameters and the temperature distribution of the sampler and related influencing factors were obtained. Optimization analysis was conducted using the simulation data and related parameters and the magnitude ranges of the parameters were obtained that could meet the design temperature requirements. The experimental data and simulation results indicated that the results were in good agreement with the realities, and this sampler might be of value for seabed sediment sampler design and manufacture.展开更多
The effects of vacuum assistance on the microstructure and mechanical properties of high pressure die cast A390alloy at different slow shot speeds were evaluated.Plate-shaped specimens of hypereutectic A390aluminum al...The effects of vacuum assistance on the microstructure and mechanical properties of high pressure die cast A390alloy at different slow shot speeds were evaluated.Plate-shaped specimens of hypereutectic A390aluminum alloy were produced on a TOYO BD?350V5cold chamber die casting machine incorporated with a self-improved TOYO vacuum system.According to the results,the vacuum pressure inside the die cavity increased linearly with the increasing slow shot speed at the beginning of mold filling.Meanwhile,tensile properties of vacuum die castings were deteriorated by the porosity content.In addition,the average primary silicon size decreased from23to14μm when the slow shot speed increased from0.05to0.2m/s,which has a binary functional relationship with the slow shot speed.After heat treatment,microstructural morphologies revealed that needle-shaped and thin-flaked eutectic silicon particles became rounded while Al2Cu dissolved intoα(Al)matrix.Furthermore,the fractography revealed that the fracture mechanism has evolved from brittle transgranular fracture to a fracture mode with many dimples after heat treatment.展开更多
文摘本文给出了使生灭过程{X(t),t≥0}有真分布的充分条件与必要条件,所谓真分布即 sum i=0 to ∞ p_1(t)=1,其中 p_1(t)=P(X(t)=i),所获得的结果与[1]、[5]的主要区别在于所有条件都是加在生灭系数之和之上的,且特别强调了生灭微分方程解的唯一性的至关重要性,此外在较宽松的条件下彻底推广了Feller-Lundberg 定理。
基金The Sci-Tech Achievements Transformation Program of Colleges and Universities in Jiangsu Province(No.JH09-13)the Research Fund of Nanjing Institute of Technology(No.YKJ201005)
文摘In order to study the thermoelectric efficiency of microwave heating and reproduction of asphalt pavements and the uniformity of reproduction temperature distribution, a waveguide excitation cavity is designed and applied to the structural design of a microwave heater. The structural sizes of the incentive cavities are determined based on the waveguide transmission line theory. Using IE3D software, electromagnetic simulations are respectively carried out in four different situations, including the distances between the magnetron probes （antennas） and a short-circuit board, different horn electric lengths and aperture sizes, different dielectric properties of the asphalt mixture, and the distances between the asphalt surface and the mouth cavity. The results show that, when the distance between the magnetron probe and the short-circuit board is 32.5 ram, it is the best installation site; reduction of aerial length is the main factor in improving the heating uniformity. When the aggregate is limestone, the best heating effect can be produced. Maximum radiation efficiency can be realized by adjusting the space between the heater radiation port and the asphalt pavement. The experimental results of asphalt mixture heating in four different situations have a substantial agreement with the simulation results, which confirms that the developed microwave heater can achieve better impedance matching, thus improving the quality and efficiency of heating regeneration.
文摘An attempt has been made to develop a distributed software infrastructure model for onboard data fusion system simulation, which is also applied to netted radar systems, onboard distributed detection systems and advanced C3I systems. Two architectures are provided and verified: one is based on pure TCP/IP protocol and C/S model, and implemented with Winsock, the other is based on CORBA (common object request broker architecture). The performance of data fusion simulation system, i.e. reliability, flexibility and scalability, is improved and enhanced by two models. The study of them makes valuable explore on incorporating the distributed computation concepts into radar system simulation techniques.
文摘Based on the character of the modular self-reconfigurable （MSR） robot, a novel homogeneous and lattice MSR robot, M-Cubes, was designed. Each module unit of the robot has 12 freedoms and is composed of six rotary joints and one cubic link. An attached/detached mechanism was designed on the rotary joints. A novel space transmitting system was placed on the inner portion of the cubic link. A motor separately transmitted torque to the six joints which were distributed equally on six surfaces of the cubic link. The example of a basic motion for the module was demonstrated. The result shows that the robot is concise and compact in structure, highly efficient in transmission, credible in connecting, and simple in controlling. At the same time, a simulator is developed to graphically design the system configuration, the reconfiguration process and the motion of cluster modules. The character of local action for the cellular automata （CA） is utilized. Each module is simplified as a cell. The transition rules of the CA are developed to combine with the genetic algorithm （GA） and applied to each module to accomplish distributed control. Simulation proves that the method is effective and feasible.
文摘Based on MATRIXx, a universal real-time visual distributed simulation system is developed. The system can receive different input data from network or local terminal. Application models in the simulation modules can automatically get such data to be analyzed and calculated, and then produce real-time simulation control information. Meanwhile, this paper designs relevant simulation components to implement the input and output data, which can guarantee the real-time and universal of the data transmission. Result of the experimental system shows that the real-time performance of the simulation is perfect.
文摘The development process as well as the core theory of distributed interactive simulation and high level architecture are discussed, and combined with graphics features, a system of real time distributed visual simulation is established. Based on computer network, simulation platform is built by installing related software and modeling object, and the interactive functions are extended by programming. A set of solutions for building a distributed visual simulation system that include both hardware and software are put forward, and a practical instance is also provided. The whole building process can be summarized into two steps that are scheme consideration and system realization.
文摘A unified model which is used to study the launching and travelling dynamic properties of a rlcket/launcher system is established. In this model, the rocket, the launcher,and the launching vehicle are considered as an interacting dynamic system in order to study the dynamic interaction between the various parts of the system and the optimal parameter matching among the above mentioned parts. The following random factors are taken into account in this paper. road surface excitation. rocket mass center misalignment, thrust misalignment, dynamic of the rocket, and the cross wind. Based on this unified model, a computer simulation software is developed, some simulation work has been carried out, and certain beneficial results have been achieved.
基金supported by The Key Technologies Research and Development Program of Shandong Province (Grant No.2006GG2206013)Foundation Sciences Funds of Qingdao (2007-2-3-15-jch)State Key Laboratory of Ocean Engineering at Shanghai Jiao Tong University (Grant No. XXXX0701)
文摘A new seabed sediment fidelity sampler was developed and its thermal insulation performance was studied and analyzed. The temperature distribution simulation indicated that the sample quality could be insured by using this new sampler. Based on ANSYS10, the temperature finite element model of the sample cylinder was established. According to the law of conservation of energy, the unsteady heat transmit equation of the sampler under solid-liquid coupling condition was derived, then the mathematical model calculation was carried out by using a mixed finite-element finite-difference method, and two thermal insulation methods were used. The simulation was carried out by using the thickness of the thermal insulation layer and heat conductivity as the variable parameters and the temperature distribution of the sampler and related influencing factors were obtained. Optimization analysis was conducted using the simulation data and related parameters and the magnitude ranges of the parameters were obtained that could meet the design temperature requirements. The experimental data and simulation results indicated that the results were in good agreement with the realities, and this sampler might be of value for seabed sediment sampler design and manufacture.
基金Project(51775297)supported by the National Natural Science Foundation of ChinaProject(2015M580093)supported by the China Postdoctoral Science Foundation
文摘The effects of vacuum assistance on the microstructure and mechanical properties of high pressure die cast A390alloy at different slow shot speeds were evaluated.Plate-shaped specimens of hypereutectic A390aluminum alloy were produced on a TOYO BD?350V5cold chamber die casting machine incorporated with a self-improved TOYO vacuum system.According to the results,the vacuum pressure inside the die cavity increased linearly with the increasing slow shot speed at the beginning of mold filling.Meanwhile,tensile properties of vacuum die castings were deteriorated by the porosity content.In addition,the average primary silicon size decreased from23to14μm when the slow shot speed increased from0.05to0.2m/s,which has a binary functional relationship with the slow shot speed.After heat treatment,microstructural morphologies revealed that needle-shaped and thin-flaked eutectic silicon particles became rounded while Al2Cu dissolved intoα(Al)matrix.Furthermore,the fractography revealed that the fracture mechanism has evolved from brittle transgranular fracture to a fracture mode with many dimples after heat treatment.
