下地幔矿物研究及其进展

文中综述了20世纪90年代以来对下地幔矿物高温高压研究的进展,详细评论了下地幔温压下(Mg,Fe)SiO3钙钛矿的稳定性、(Mg, Fe)SiO3 钙钛矿和(Mg, Fe)O镁方铁矿的高压状态方程和热弹性及高压熔化、核幔边界温压下铁和硅酸盐的化学反应等几个热点问题;探讨了下地幔的矿物学组成,对下地幔的地震波速异常给出了可能的矿物学解释;介绍了国内同领域的研究工作;展望了下地幔矿物研究的发展方向。

Research on anisotropy of shale oil reservoir based on rock physics model

Rock physics modeling is implemented for shales in the Luojia area of the Zhanhua topographic depression. In the rock physics model, the clay lamination parameter is introduced into the Backus averaging theory for the description of anisotropy related to the preferred alignment of clay particles, and the Chapman multi-scale fracture theory is used to calculate anisotropy relating to the fracture system. In accordance with geological features of shales in the study area, horizontal fractures are regarded as the dominant factor in the prediction of fracture density and anisotropy parameters for the inversion scheme. Results indicate that the horizontal fracture density obtained has good agreement with horizontal permeability measured from cores, and thus confirms the applicability of the proposed rock physics model and inversion method. Fracture density can thus be regarded as an indicator of reservoir permeability. In addition, the anisotropy parameter of the P-wave is higher than that of the S-wave due to the presence of horizontal fractures. Fracture density has an obvious positive correlation with P-wave anisotropy, and the clay content shows a positive correlation with S-wave anisotropy, which fully shows that fracture density has a negative correlation with clay and quartz contents and a positive relation with carbonate contents.

Soil properties in reclaimed farmland by filling subsidence basin due to underground coal mining with mineral wastes in China

Reclaimed mining-induced subsidence area soils (RMSs) could restore soil quality and crop productivity in coal mining area. This study was conducted to evaluate the effects of mineral-processing wastes (fly ash vs coal gangue) as backfill substrates on soil chemical and microbial properties in mining-induced subsidence area. A general higher water holding capacity (WHC) and pH had been observed in fly ash than coal gangue reconstructed soil. Soil microbial biomass C (MBC) and N (MBN), MBC/TOC (total organic carbon) ratio (qmic) were higher under the influence of the fly ash, while contents of As, Cr, C/Nbio, the basal respiration per unit of microbial biomass (QCO2) were higher under the coal gangue reconstructed mode in 0-10, 10-20, 20-50 cm layers. The microbial basal respiration was higher in 0-10, 10-20, 0-50 cm layers, while was lower in 20-50 cm layer under fly ash than that of coal gangue reconstructed mode. The lower QCO2 of fly ash mine soil suggested the lower maintenance energy requirement of the microbial community. Moreover, the contents of metals may possibly have negative implications for soil microbial and enzyme activities in reconstructed soil.

Bioaccessibility of Vanadium from Soil and Mineral Measured by in vitro Model

[Objective] This study aimed to investigate the existing forms and bioaccessibility of vanadium（V） from soil and mineral of Panzhihua region.[Method] The representative Xigeda soil and vanadium-titanium magnetite were collected from Panzhihua region to determine the existing forms of vanadium from soil and mineral;in vitro bionic digestion model was established to measure the bioaccessibility of vanadium.[Result] The dissolved concentrations of vanadium from farmland,mining area and vanadium-titanium magnetite in gastric juice were respectively 5.02,9.50 and 3.88 mg/kg,and the bioaccessibility ranged from 0.09% to 3.00%;the dissolved concentrations of vanadium in intestinal juice were respectively 2.98,5.43 and 4.49 mg/kg,and the bioaccessibility ranged from 0.10% to 1.78%.The content of vanadium in various existing forms varied significantly,the contents of vanadium in non-specific adsorption state and specific adsorption state were low,but residual content was completely high,which accounted for 75.06%,95.32% and 86.27% of the total content of vanadium in samples.[Conclusion] Bioaccessibility of dissolved vanadium in gastric juice was higher than that in small intestinal juice.Vanadium from soil and mineral was difficult to generate morphological transformation and migration,which was the main reason for low bioaccessibility.

Sulfide mineral bioleaching:Understanding of microbe-chemistry assisted hydrometallurgy technology and acid mine drainage environment protection

Bioleaching is regarded as an essential technology to treat low grade minerals,with the distinctive superiorities of lower-cost and environment-friendly compared with traditional pyrometallurgy method.However,the bioleaching efficiency is unsatisfactory owing to the passivation film formed on the minerals surface.It is of particular interest to know the dissolution and passivation mechanism of sulfide minerals in the presence of microorganism.Although bioleaching can be useful in extracting metals,it is a double-edged sword.Metallurgical activities have caused serious environmental problems such as acid mine drainage(AMD).The understanding of some common sulfide minerals bioleaching processes and protection of AMD environment is reviewed in this article.

Sorption and Fractionation of a Peat Derived Humic Acid by Kaolinite, Montmorillonite, and Goethite

Sorption of humic acid （HA） on mineral surfaces has a profound interest regarding the fate of hydrophobic organic contaminants （HOCs） and carbon sequestration in soils. The objective of our study is to determine the fractionation behavior of HA upon sorption on mineral surfaces with varying surface properties. HA was coated sequentially on kaolinite （1：1 clay）, montmorillonite （2：1 clay）, and goethite （iron oxide） for four times. The unadsorbed HA fractions were characterized by elemental analysis, diffuse reflectance infrared Fourier transform spectroscopy （DRIFT）, and solid state 13C nuclear magnetic resonance spectroscopy （NMR）. The mineral-HA complexes were characterized by DRIFT. Polarity index [（N＋O）/C] revealed higher polarity of the unadsorbed HA fractions after coating on kaolinite, reflecting that relatively higher polarity fractions of HA remain unadsorbed. Sorption of aiiphatic alcohol fraction along with carbohydrate was prominent on kaolinite surface. DRIFT results of the unadsorbed HA fractions indicated more sorption of aiiphatic moieties on both kaolinite and montmorillonite. DRIFT results of the unadsorbed HA fractions after sorption on kaolinite and goethite showed the sorption of the proteinaceons fractions of HA. The HA fractions obtained after coating on goethite showed significant sorption of carboxylic moieties. The results mentioned above comply reasonably well with the DRIFT spectra of the minerai-HA complexes. ^13C NMR results showed higher sorption of anomeric C on kaolinite surface. Higher sorption of paraffinic fraction waS observed on montmorillonite. NMR data inferred the sorption of carboxylic moieties on goethite surface. Overall, this study showed that aliphatic moieties of HA preferentially sorbed on kaolinite and montmorillonite, while carboxylic functional groups play a significant role in sorption of HA on goethite. The sorbed fractions of HA may modify the mineral surface properties, and thus, the interaction with organic contaminants.

DFT calculation on relaxation and electronic structure of sulfide minerals surfaces in presence of H_2O molecule

First-principles calculations are performed to investigate the relaxation and electronic properties of sulfide minerals surfaces(MoS2, Sb2S3, Cu2 S, ZnS, PbS and FeS2) in presence of H2 O molecule. The calculated results show that the structure and electronic properties of sulfide minerals surfaces have been influenced in presence of H2 O molecule. The adsorption of the flotation reagent at the interface of mineral-water would be different from that of mineral surface due to the changes of surface structures and electronic properties caused by H2 O molecule. Hence, the influence of H2 O molecule on the reaction of flotation reagent with sulfide mineral surface will attract more attention.

Physical properties of solid fuel briquettes from bituminous coal waste and biomass

Biomass and bituminous coal fines from four different coalfields were used to produce fuel briquettes. Two physical properties of briquettes, water resistance index and compressive strength were analyzed. The influence of type and quantity of biomass on physical properties was also studied. The results reveal that depending on the mineral content of the coal, the physical properties of the briquettes differ noticeably. The comparison of briquettes with and without biomass showed that the presence of the beet pulp increased CS in all types of coal samples. Samples containing beet pulp had better physical properties than sawdust. Mezino II coal briquettes had highest CS and WRI than the other ones. Calorific value of biomass/Mezino lI coal briquettes was lessened in comparison with raw coal, but it remained in an acceptable range.

Negative effect of dissolved organic compounds on settling behavior of synthetic monominerals in red mud

Hydration grossular and hematite monominerals were synthesized. The effects of dissolved organic compounds(including sodium formate, sodium acetate, sodium oxalate, sodium salicylate or disodium phthalate) on the settling performance of hydration grossular or hematite slurries were studied. The settling of the slurries was also investigated with the addition of sodium polyacrylate(PAAS) or hydroxamated polyacrylamide flocculant(HCPAM). The adsorption mechanism of organic compounds on monominerals surfaces was studied by FT-IR and XPS, respectively. A deterioration in settling is observed in order of disodium phthalate>sodium salicylate>sodium oxalate>sodium formate(or sodium acetate). Moreover, PAAS can efficiently eliminate the negative effects of organic compounds on the settling performance of the hydration grossular slurry. HCPAM can efficiently eliminate the negative effects of sodium formate, sodium acetate and sodium oxalate on the settling performance of the hematite slurry, but it only partially improves the settling performance of hematite slurry containing sodium salicylate or disodium phthalate. FT-IR and XPS results show that organic compounds are physically adsorbed on hydration grossular surface, and chemisorptions of organic compounds occur on hematite surface with a bidentate chelating complex.

Study and application of Toxicity Test Method Using Neomysis awatschensis in Toxicity Evaluation of Drilling Fluid

Neomysis awatschensis was collected on the west coast of Jiaozhou Bay, Qingdao in 1992 and acclimated in the laboratory conditions. The acute toxicity method using 4~ 6 day juvenile mysid of this species is studied. The species is compared with M. bahia in taxonomy, geographic distribution, morphology, as well as the sensitivity to reference toxins. Based on the results, we recommend N. awatschensis to be a standard marine organism for toxicity test in China and the method to be applied in toxicity evaluation of drilling fluids. In this paper, we report the results of the above studies and the application of the method in the evaluation of several drilling fluid products.

Study the Physical, Chemical, Mineralogical, and Geo-technical Properties of Soils Used in Pottery Industries, Kurdistan-lraq

The study area is located in Duhok and Sulaimania province in Kurdistan region, lraq. Study soils developed from parent material that has derived from limestone. Randomize, composed and disturbed surface soil samples were collected. The bulk soils were air dried, crushed and passed through 2 mm sieve. Standard methods were used for chemical, physical, geotechnical and mineralogical analyses of soil samples. The results indicated that the study soils texture were clay to loam clay, this texture was considered as suitable for ceramic and pottery industries as a result of increasing clay contents that ranged between 301 g/kg and 676 g/kg. Soil consistence depending on geotechnical properties increased the ability of study soils for resistance rapture and deformation. Existence the high amount of cementing agents in study soils such as organic matter, iron oxides and particularly total carbonate （247.2-308.8 g/kg） act to reduce the bad effect of the smectite minerals group （high shrinkage） in soils of study locations through increasing the resistance of these soils for rupture and deformation. The existing of Kaolinite, palygorskite and chlorite allows clay to be dried in ceramic and pottery industries without cracking from shrinkage. Study soils were different in their colors as a result of existence, different pigmentation materials that led to coloring soils with different colors in turn caused coloring of pottery and ceramic materials. Since, there are no available academic studies or researches about this subject in Kurdistan region in addition the clay pottery and ceramic sector still has a good market at the same time using this type of soils for arts, therefore, this study was conducted.

Reservoir space of the Es_3~3–Es_4~1shale in Dongying sag

The Es3/3-Es1/4 shales in Dongying sag are source rocks with large reserves of shale oil and gas. For the iden- tification of development characteristics and geological significance of the reservoir space, FM1 logging, core observation, thin section analysis, X-ray diffraction, fluorescence microscopy, scanning electron microscopy, mercury porosimetry, low-temperature nitrogen adsorption, atomic force microscopy, and conventional physical property testing were used to study the petrology and reservoir space of the Es3/3-Es1/4 shale in Dongying sag. The results suggest that the shale is rich in carbonate minerals. Phanero- crystalline stratiform and lamellar argillaceous limestone and calcareous claystone are the oil- and gas-bearing lithofacies. The oil in the micropores is mainly present as membranes and clots. The shale reservoir space has a network structure with veins, carbonate and clay minerals, and micropores among pyrite and the matrix. The results provide the geological framework for future shale oil and gas explora- tion in Dongying sag.

Physicochemical properties and heavy metals leachability of fly ash from coal-fired power plant

The physicochemical properties of fly ash from two kinds of coal-fired power plants were studied. Three aspects were examined： the micro-morphology, the mineral composition and the content of heavy metals. The results show that the fly ash from plants using a circulating fluidized bed are more irregular par- ticles, while the particles from the plants using a pulverized coal-fired boiler are mainly spherical in shape. Quartz and mullite are the main crystalline phases in the ash. Clearly, both the technology and the coal used by a power plant can influence the mineral composition of the ash. The mineral composition of fly ash from a circulating fiuidized bed is more complex than that from a pulverized coal-fired boiler. The quantity of elements found in the fly ash is greater than that found in the bottom ash for the same plant. Heavy metals are likely to be enriched in the fly ash. Heavy metal leachability was studied using two leaching methods. The results indicate that most of the heavy metals that leached during either batch leaching or column leaching experiments did not exceed the related maximum concentration standards. But Ni concentrations in the leachates from both batch and column tests exceed the standard. The highest excess rates in both tests were 572~ and 497~, which levels might threaten the environment.

Ash-and-Slag Wastes of Energy Sector as Raw Material for Production of Rare-Earth Metals and Alumina

The results to develop a complex technology of co-extraction of germanium and gallium from the ash-and-slag wastes of coal combustion in Ukraine were presented. Based on the study of phase changes occurring in initial raw materials as a result of its processing, it was proposed to carry out a preliminary enrichment of the raw materials in order to produce secondary sublimates. Their further processing involves a combination of leaching soluble material with distillation of germanium in the form of tetrachloride. The resulting acidic solutions are trended to the gallium extraction. Optimum conditions of carrying out of processes are recommended.The chemical and phase composition of the resulting dump products and solutions have been defined. On the basis of it ways of their processing for the purpose of reception of alumina and building materials are recommended.

ADSORPTION CAPACITY OF ACTIVATED CARBON FIBER FABRIC IN CYANIDE LEACHING LIQUOR OF GOLD ORES

Adsorption capacity of ACFF in cyanide leaching liquor of gold ores was studied with cyanide leaching liquor of gold ores, containing various kinds of ions. The adsorbed leaching liquor was analyzed by atomic emission spectroscopy and colorimetric method. The contents of various kinds of ions in ACFF were determined with X-ray photoctron spectroscopy. ACFF not only adsorbed gold but also adsorbed arsenic, nickel, zinc, calcium, sulphur, bismuth, copper, iron, silver and cyanide anion. Atomic percentage of C and those of O, N, Zn, Fe increase and decrease respectively with the increase of the layer depth, while those of Ca, Au, Ag keep constant.

Electrokinetic and Flotation Investigations of Surface Properties Modification of Magnesite and Serpentinite Using Biosurfactants and Surfactants

This paper presents some results of zeta potential measurements performed into biosurfactant adsorption onto magnesite and serpentinite surface. Zeta potential and isoelectric point measurement of magnesite and serpentinite particles before and after interaction with biosurfactant broth solution and activator （nickel（II） ion solution） were carried out. The zeta potential results show that presence of biosurfactants changes both magnesite and serpentinite surface potential by physical adsorption which increases the hydrophobicity of mineral particles. Measurements of particles zeta potential in the presence of biosurfactant broth are relevant to the minerals flotation. Hallimod flotation response of magnesite and serpentinite as a function of collector concentration was investigated. Bioflotation test results show that at the presence of broth, the flotation separation of magnesite from serpentinite is possible.

Characterization of semi-coke generated by coal-based direct reduction process of siderite

Solid wastes derived from metallurgical industries pose a significant threat to environment. The utilization and disposal of these solid wastes are the major concern in the world. Semi-coke generated in coal-based direct reduction process of iron ore is a by-product and its suitable utilization is not available so far. In order to handle it properly, the characteristics of this by-product were comprehensively investigated. A series of analysis methods were used to demonstrate its mineral compositions, petrography and physico-chemical properties. The results reveal that the semi-coke has poor washability. The fixed carbon content of semi-coke reaches 76.11% and the gross calorific value is 28.10 MJ/kg, both of which are similar to those of traditional sinter coke breeze. Also, semi-coke ash possesses lower content of SiO2, Al2O3, S and higher content of CaO and MgO, which could improve the strength of sinter ore when partially substituting for coke breeze in sintering. Semi-coke features well-development porous structure and higher reaction activity, which predicts that the sintering speed could be elevated to some extent when employing it as a partial replacement of coke breeze, so the studies further suggest that the potential adverse effect of the high reactivity on sintering process could be weakened by adequately coarsening the semi-coke's particle size.

Practice and design of the self-purification system for heavy metals-bearing contaminants

Many minerals in nature have self-purification capacity to hold and stabilize deleterious contaminants into their lattice structures,which can be used for treatment of heavy metals-bearing contaminants. Hydrotalcite Layer Double Hydroxide (LDH),tobermorite Calcium Silicate Hydrate (CSH) and apatite are ubiquitous minerals in nature,having higher geochemical stability and potential for binding and stabilizing heavy metals. Based on the elucidation of crystal structure property and self-purification principles of the three minerals above,this article discussed how to design the self-purification system of heavy metal-bearing contaminants.

Influence of Mineral Admixtures on Essential Properties of Ternary Cement Blends

Two CaCO3-based materials （limestone and clamshells） and steel slag were used as mineral admixtures in cement to produce ternary blends and their influences on hydration and portlandite formation were analyzed. Additionally, mechanical properties were determined. These properties were determined using X-ray diffraction and scanning electron microscopic/energy dispersive X-ray analytical techniques as well as applying methods specified by EN （European Standards） and ASTM （American Standards for Testing and Materials）. The portlandite （Ca（OH）E） content was considerably reduced from 36.9% of reference cement to between 13.79% and 15.5%. With the water demand and setting times of the cements containing up to 10%, admixtures did not change significantly. The mechanical tests results showed that ternary blends produced 2-day strengths higher than that specified by EN 197-1 and that blends containing up to 20% admixtures can be used to produce both Class 32.5N and 42.5N cements.

Long-Term Effect of Organic and Mineral Fertilization on Soil Physical Properties Under Greenhouse and Outdoor Management Practices

To evaluate the use of organic amendments as an alternative to conventional fertilization,a 10-year experiment on a loam soil was conducted under a crop rotation system in both greenhouse and outdoor plots applied with chemical fertilizers (NPK) and vegetal compost (organic fertilizer) in the Guadalquivir River Valley,Spain.The effect of these two different fertilization regimes on the soil physical properties was evaluated.Soil organic carbon (OC),soil bulk density (BD),soil water retention (WR),available water content (AWC),aggregate stability (AS),and soil physical quality (Dexter's index,S) were determined.The use of organic fertilizer increased OC and resulted in a significant increase in AS and a decrease in BD compared to the mineral fertilizer application in both greenhouse and outdoor plots.The outdoor plots showed the lowest BD values whereas the greenhouse plots showed the highest AS values.In the last years of the 10-year experiment the S parameter was significantly higher in organic fertilizer plots,especially for greenhouse plots.At the end of the study period,there were no significant differences in WR at field capacity (FC) between treatments in both systems;the AWC was also similar in the greenhouse plots but higher in the mineral outdoor plots.In mineral fertilizer treatments,a small improvement in the physical properties was also observed due to the utilization of less aggressive tillage compared with the previous intensive cropping system.Physical soil properties were correlated with soil OC.The sustainable management techniques such as the use of organic amendments and low or no tillage improved soil physical properties,despite the differences in management that logically significantly affected the results.