新型碳基渗滤膜在易燃液体残留物提取检验中的应用

用自制的碳基渗滤膜,以自制的红外提取装置测定了该膜对苯的回收率为68%,考察了温度、压力、提取时间等对碳基渗滤膜应用的影响,主要介绍了将该碳基渗滤膜应用于现场易燃液体残留物的提取,通过水泥地面添加易燃液体的提取检验,棉布、化纤布上易燃液体残留物的提取检验测试了碳基渗透膜的提取回收能力。该碳基渗滤膜可以应用于纵火现场易燃液体残留物的提取检验。

Li_2O_MgO-Al_2O_3-SiO_2系高温低膨胀釉的制备及性能研究

以焦炉炉门堇青石衬砖的使用情况为依据,得出适合堇青石衬砖高温低膨胀釉的体系为Li_2O-MgO-Al_2O_3-SiO_2系。釉料在合理的化学组成范围内生成董青石与β-锂辉石固溶体晶体。试验成功的研制出适用于堇青石衬砖的高温低膨胀釉,釉料在1350℃与堇青石砖共同烧成,釉层能均匀光滑的铺展在堇青石衬砖表面,它能在1200℃下使用而不融化,它的热膨胀系数为2.85×10^(-6),在20℃～1000℃并且还有待于进一步降低。釉与堇青石村砖热膨胀相匹配,因此釉层经五次热震(1100℃,水冷)后的没有裂纹出现。XRD物相分析得出釉有堇青石与β-锂辉石固溶体晶体相生成。釉能填充堇青石衬砖表面的气孔并以自身的高致密性防止了有害物质向砖内部渗透,起保护层作用。

砷铅锌烧渣中金的氰化浸出研究

砷铅锌烧渣与渗透剂一起磨至100％通过-200目后置于搅拌槽中，在选择条件下，用碳浆工艺氰化浸出，可使烧渣中金的含量从7．3g／t下降到0．5～1g／t，具有较好的经济效益。

Permeability and Selectivity of Sulfur Dioxide and Carbon Dioxide in Supported Ionic Liquid Membranes

Permeabilities and selectivities of gases such as carbon dioxide （CO2）, sulfur dioxide （SO2）, nitrogen （N2） and methane （CH4） in six imidazolium-based ionic liquids （[emim][BF4], [bmim][BF4], [bmim][PF6], [banim][BF4], [bmim][Tf2N] and [emim][CF3SO3]） supported on polyethersulfone microfiltration membranes are investigated in a single gas feed system using nitrogen as the environment and reference component at temperature from 25 to 45℃ and pressure of N2 from 100 to 400 kPa. It is found that SO2 has the highest permeability in the tested supported ionic liquid membranes, being an order of magnitude higher than that of CO2, and about 2 to 3 orders of magnitude larger than those of N2 and CH4. The observed selectivity of SO2 over the two ordinary gas components is also striking. It is shown experimentally that the dissolution and transport of gas components in the supported ionic liquid membranes, as well as the nature of ionic liquids play important roles in the gas permeation. A nonlinear increase of permeation rate with temperature and operation pressure is also observed for all sample gases. By considering the factors that influence the permeabilities and selectivities of CO2 and SO2, it is expected to develop an optimal supported ionic liquid membrane technology for the isolation of acidic gases in the near future.

Ceramic Supported PDMS and PEGDA Composite Membranes for CO2 Separation

Composite membranes have attracted increasing attentions owing to their potential applications for CO2 separation. In this work, ceramic supported polydimethylsiloxane （PDMS） and poly （ethylene glycol） diacrylate （PEGDA） composite membranes were prepared. The microstructure and physicochemical properties of the compos- ite membranes were characterized. Preparation conditions were systematically optimized. The gas separation performance of the as-prepared membranes was studied by pure gas and binary gas permeation measurement of CO〉 N2 and H〉 Experiments showed that PDMS, as silicone rubber, exhibited larger permeance and lower separation factors. Conversely, PEGDA composite membrane presented smaller gas permeance but higher ideal selectivity for CO2/N2. Compared to the performance of those membranes using polymeric supports or freestanding membranes, the two kinds of ceramic supported composite membranes exhibited higher gas permeance and acceptable selectivity. Therefore, the ceramic supported composite membrane can be expected as a candidate for CO2 separation from light gases.

Carbon liberated from CO-releasing molecules attenuates leukocyte infiltration in the small intestine of thermally injured mice

AIM： To determine whether Carbon （CO） liberated from CO-releasing molecules attenuates leukocyte infiltration in the small intestine of thermally injured mice. METHODS： Thirty-six mice were assigned to four groups. Mice in the sham group （n = 9） were underwent to sham thermal injury; mice in the burn group （n = 9） received 15% total body surface area full-thickness thermal injury; mice in the burn ＋ CORM-2 group （n = 9） were underwent to the same thermal injury with immediate administration of tricarbonyldichlororut henium （11） dimer CORM-2 （8 mg/kg, i.v.）; and mice in the burn＋DMSO group （n = 9） were underwent to the same thermal injury with immediate administration of 160 IJL bolus injection of 0.5% DMSO/saline. Histological alterations and granulocyte infiltration of the small intestine were assessed. Polymorphonuclear neutrophil （PMN） accumulation （myeloperoxidase assay） was assessed in mice mid-ileum. Activation of nuclear factor （NF）-KB, expression levels of intercellular adhesion molecule-1 （ICAM-1） and inducible heme oxygenase in mid-ileum were assessed. RESULTS： Treatment of thermally injured mice with CORM-2 attenuated PMN accumulation and prevented activation of NF-kB in the small intestine. This was accompanied by a decrease in the expression of ICAM-1. In parallel, burn-induced granulocyte infiltration in mid- ileum was markedly decreased in the burn mice treated with CORM-2. CONCLUSION： CORM-released CO attenuates leukocyteinfiltration in the small intestine of thermally injured mice by interfering with NF-KB activation and protein expression of ICAM-1, and therefore suppressing the pro-adhesive phenotype of endothelial cells.

Permeability variation characteristics of coal after injecting carbon dioxide into a coal seam

A theoretical basis for the optimization of carbon dioxide injection parameters and the development of the drainage system can be provided by identifying the permeability change characteristic of coal and rock after injection of carbon dioxide into the coal seam. Sihe, Yuwu, and Changcun mines were used as research sites. Scanning electron microscopy and permeability instruments were used to measure coal properties such as permeability and surface structure of the coal samples at different pH values of carbon dioxide solution and over different timescales. The results show that the reaction between minerals in coal and carbonate solution exhibit positive and negative aspects of permeability-the dissolution reaction between carbonate minerals in coal and acid solution improves the conductivity of coal whilst, on the other hand, the clay minerals in the coal （mainly including montmorillonite, illite and kaolinite） exhibit expansion as a result of ion exchange with the H~ in acid solution, which has a negative effect on the per- meability of the coal. The permeability of coal samples increased at first and then decreased with immer- sion time, and when the soaking time is 2-3 months the permeability of the coal reached a maximum. In general, for coals with permeabilities less than 0.2 mD or greater than 2 roD, the effect on the permeabil- ity is low： when the permeability of the coal is in the range 0.2-2 mD, the effect on the permeability is highest. Research into permeability change characteristics can provide a theoretical basis for carbon diox- ide injection under different reservoir permeability conditions and subsequent drainage.

Mechanism of CO_2 enhanced CBM recovery in China: a review

Permeability of coal reservoirs in China is in general low. Injection of CO2 into coal seams is one of the potential ap-proaches for enhancing coalbed methane (CBM) production. The feasibility of this technology has been investigated in China since the 1990s. Advances in mechanism of CO2 enhanced CBM recovery (CO2-ECBM) in China are reviewed in light of certain aspects, such as the competitive multi-component gas adsorption, sorption-induced coal swelling/shrinkage and its potential effect on CBM production and numerical simulation for CO2-ECBM recovery. Newer investigations for improving the technology are discussed. It is suggested that a comprehensive feasibility demonstration in terms of geology, technology, economics and environment-carrying capacity is necessary for a successful application of the technology for CBM recovery in China. The demonstration should be car-ried out after more investigations into such facets as the control of coal components and structure to a competitive multi-component-gas adsorption, the behavior and essence of super-critical adsorption by coal of gas, environmental and safe feasi-bility of coal mining after CO2 injection and more extensive pilot tests for CO2-ECBM recovery.

Effect of Working Temperature on the Resistance Characteristic of a Pleated Stainless Steel Woven Filter

Effect of working temperature on the resistance characteristic including the permeability coefficient and the pressure drop evolution of a pleated stainless steel woven filter with a nominal pore size of 0.5 μm has been studied. The permeability coefficient was obtained based on the pressure drop data and the Darcy＇s law. In three filtration experiments, pure carbon dioxide at 283 K, nitrogen at 85 K and liquid helium at 18 K are adopted, respectively. It is found that the permeability coefficient decreases at the working temperature due to the cold shrink of the filter element at cryogenic temperature. Then, two kinds of feed slurries, mixture of liquid nitrogen and solid carbon dioxide at 85 K, and mixture of liquid helium and solid nitrogen at 18 K, flow into the filter cell. The solid particles are deposited on the filter surface to form a filter cake and the purified liquid flows through the filter. It is found that the pressure drop evolution shows the same trend on these two temperatures, which can be divided into three stages with high filtration efficiency, indicating the feasibility of the filter for cryogenic application. However, variant cake resistances are obtained, which is resulted from the different interactions between solid particles in the feed slurry at lower working temperature.

Influence of Temperature on the Performance of Forward Osmosis Using Ammonium Bicarbonate as Draw Solute

This study investigated the influence of temperature on the performance of forward osmosis(FO) under the condition that the feed solution(FS) temperature was diff erent from draw solution(DS) temperature. An FO model considering the mass and heat transfer between FS and DS was developed, and the FO experiment with ammonium bicarbonate solution as DS and sodium chloride solution as FS was carried out. The predicted water flux and reverse draw solute flux using the developed model coincided with the experimental fluxes. Increases in the temperature of FS or DS yield corresponding increases in the water flux, reverse draw solute flux, and forward rejection of feed solute. Compared with increasing the FS temperature, increasing the DS temperature has a more significant impact on enhancing FO performance. When the temperature of DS increased from 20 to 40 ℃, the specific reverse solute flux decreased from 0.231 to 0.190 mol/L.

Laboratory determination of fracture aperture, permeability and stress repationships

It is well known that the formation permeability is not a constant but a function of the in situ stress environment. This study has been primarily carried out numerically, and to a certain extent, in the field. However, since the rock properties are generally tested in the laboratory, this last situation needs to be modeled to maintain consistent scales in the analysis. In this paper, concepts and techniques of laboratory experiments are presented to determine relationships between fracture aperture and external loading in simulated rocks (concrete).

In-situ preparation, modulation and mechanism of refractory metal carbide gradient coating

TiC, ZrC and TaC modified layers were in-situ prepared on graphite matrix by chemical vapor infiltration method with metal salts as the activator. Taking the TiC modified layer as an example, through thermodynamic calculation and experiment, the thermal decomposition process of raw materials(Ti/K_(2)TiF_(6)) was analyzed, the formation mechanism of TiC was determined, and the distribution of TiC modified layer was modulated. The results show that activator K_(2)TiF_(6)has higher decomposition temperature than NH4Cl, which is conducive to improving the utilization rate of raw materials in the gas infiltration process. Increasing the content of Ti powder can increase the concentration of reaction gas and contribute to the formation of TiC modified layer. When the molar ratio of Ti to K_(2)TiF_(6)is 3:1, the surface thickness and infiltration depth of Ti C are 5.42 and 136.24 μm, respectively. Increasing the reaction temperature can improve the rate of in-situ reaction and the thickness of TiC surface layer. When the experimental temperature rises to 1600 °C, the TiC surface layer thickness increases to 20.27 μm.

小学科学教学中渗透低碳意识之浅见

小学科学是一门很重要的实践性学科知识,它主要是为了培养小学生的科学素养和实践动手能力,也因此受到了社会各界的高度重视。但是对于很多中小学校而言,小学科学教学等各方面的资源都相对比较缺乏,因此使得相关学科知识的教学活动都难以开展。尤其随着社会经济的发展和变化,低碳意识开始成为小学科学教学中的重要内容,不过研究调查发现,小学科学教学课程活动的开展实际上并没有想象中的那么顺利,尤其是很多教师在教学方法上还依旧存在诸多的问题,而这样则无法有效促使低碳意识在小学科学课堂进行渗透的。本文主要就小学科学教学中渗透低碳意识进行浅析。

Processing and properties of 2D SiC/SiC composites by precursor infiltration and pyrolysis

Two-dimensional plain-weave silicon carbide fiber fabric reinforced silicon carbide(2D-SiC/SiC)composites were molded by stacking method and densified through precursor infiltration and pyrolysis(PIP)process.SiC coating was deposited as the fiber/matrix interphase layer by chemical vapor deposition(CVD)technique.Fiber/matrix debonding and relatively long fiber pullouts were observed on the fracture surfaces.Additionally,the flexural strength and elastic modulus of the composites with and without fiber/matrix interphase layer were investigated using three-point bending test and single-edge notched beam test.The results show that the fiber fraction and the porosity of 2D-SiC/SiC composites with and without coating are 27.2%(volume fraction)and 11.1%,and 40.7%(volume fraction)and 7.5%,respectively.And the flexural strength and elastic modulus of 2D-SiC/SiC composites with and without coating are 363.3 MPa and 127.8 GPa,and 180.2 MPa and 97.2 GPa,respectively.With a proper thickness,the coating can effectively adjust the fiber/matrix interface,thus causing a dramatic increase in the mechanical properties of the composites.

Effect of nanofibers at surface of carbon fibers on microstructure of carbon/carbon composites during chemical vapor infiltration

Before densification by chemical vapor infiltration,carbon or SiC nanofibers were grown on the surface of carbon fibers by catalytic chemical vapor deposition using electroplated Ni as catalyst.The modification and mechanism of nanofibers on the pyrocarbon deposition during chemical vapor infiltration were investigated.The results show that the nanofibers improve the surface activity of the carbon fibers and become active nucleation centers during chemical vapor infiltration.They can induce the ordered deposition of pyrocarbon and adjust the interface bonding between pyrocarbon and carbon fibers during the infiltration.

Rock Cutting Analysis Employing Finite and Discrete Element Methods

The petroleum industry has shown great interest in the study of drilling optimization on pre-salt formations given the low rates of penetration observed so far. Rate of penetration is the key to economically drill the pre-salt carbonate rock. This work presents the results of numerical modeling through finite element method and discrete element method for single cutter drilling in carbonate samples. The work is relevant to understand the mechanics of drill bit-rock interaction while drilling deep wells and the results were validated with experimental data raised under simulated downhole conditions. The numerical models were carried out under different geometrical configurations, varying the cutter chamfer size and back-rake angles. The forces generated on the cutter are translated into mechanical specific energy as this parameter is often used to measure drilling efficiency. Results indicate that the chamfer size does not change significantly the mechanical specific energy values, characteristic. Results also show there is a significant increase although the cutter aggressiveness is influenced by this geometrical in drilling resistance for larger values of back-rake angle.

Complex Permittivity and Microwave Absorbing Property of Si_3N_4-SiC Composite Ceramic

Si3N4-SiC composite ceramics were fabricated by chemical vapor infiltration using porous Si3Na ceramic as preform. The average grain size of SiC was 30 nm. Relationship between SiC content and relative complex permittivity of Si3Na-SiC within the frequency range of 8.2-12.4 GHz （X-band） was investigated. The average real part of relative complex permittivity ε′ of Si3N4-SiC increased from 3.7 to 14.9 and the relative imaginary part ε″ increased from 0.017 to 13.4 when the content of SiC increased from 0 to 10 vol.%. The Si3N4-SiC ceramic with 3 vol.% SiC achieved a reflection loss below -10 dB （90% absorption） at 8.0-11.4 GHz, and the minimum value was -27.1 dB at 9.8 GHz when the sample thickness was 2.5 mm. The excellent microwave absorbing abilities of Si3N4-SiC ceramic were attributed to the interfacial polarization at interface between Si3N4 and SiC and at grain boundary between SiC nanocrystals.