Titania-based composite catalysts were prepared through a sol-gel route employing multi-walled carbon nanotubes with different diameters. The materials were characterized using thermogravimetric analysis, nitrogen ads...Titania-based composite catalysts were prepared through a sol-gel route employing multi-walled carbon nanotubes with different diameters. The materials were characterized using thermogravimetric analysis, nitrogen adsorption-desorption isotherm, powder X-ray diffraction, scanning electron microscopy, and diffuse reflectance UV-Vis absorption spectra. The application of the catalysts to photocatalytic degradation of phenol was tested under UV-Vis irradiation. A synergetic effect on phenol removal was observed in case of composite catalysts, which was evaluated in terms of apparent rate constant, total organic carbon removal and photonic efficiency.展开更多
Titania coating of multi wall carbon nano tube(MWCNT) was carried out by sol-gel method in order to improve its photo catalytic properties.The effect of MWCNT/TiO_2 mass to volume ratio on adsorption ability,reaction ...Titania coating of multi wall carbon nano tube(MWCNT) was carried out by sol-gel method in order to improve its photo catalytic properties.The effect of MWCNT/TiO_2 mass to volume ratio on adsorption ability,reaction rate and photo-catalytic removal efficiency of dibenzothiophene(DBT) from n-hexane solution was investigated using a 9 W UV lamp.The results show that the addition of nanotubes improves the photo-catalytic properties of TiO_2 by two factors;however,the DBT removal rate versus MWCNT content is found to follow a bimodal pattern.Two factors are observed to affect the removal rate of DBT and produce two optimum values for MWCNT content.First,large quantities of MWCNTs prevent light absorption by the solution and decrease removal efficiency.By contrast,a low dosage of MWCNT causes recombination of the electron holes,which also decreases the DBT removal rate.The optimum MWCNT contents in the composite are found to be 0.25 g and 0.75 g MWCNT per 80 m L of sol.展开更多
In this work, the authors present a study of dye absorption in TiO2 doped with CNTs （carbon nanotubes）. Absorption decreases exponentially with the increase of CNTs in the film, while morphological characterization,...In this work, the authors present a study of dye absorption in TiO2 doped with CNTs （carbon nanotubes）. Absorption decreases exponentially with the increase of CNTs in the film, while morphological characterization, conducted by SEM （scanning electron microscope） and TEM （transmission electron microscope） microscopes, suggests that this behavior is strongly related to morphological structure of grown films. For CNTs amounts greater than 1%, the authors observe the formation of CNTs clusters randomly distribute on TiO2 bulk, which strongly reduces the film porosity quenching the dye absorption. Comparison with optical properties of CNT/TiO2 filmstudied in the previous work, suggest that the best level of doping is with 0.5% of CNTs. FTIR （Fourier transform infrared spectroscopy） measurements conducted on a series of pristine and doped samples clearly indicate the absence of change in allotropic species of TiO2, while AFM （atomic force microscope） analysis indicates that the sample roughness strongly changes with doping, preventing the dye adsorption. Finally, measurements of cell efficiency indicate an increase of 5% in cells with 0.5% of CNT doping and a decrease for greater values.展开更多
Controlled synthesis of hierarchically assembled titanium dioxide （TiO2） nano- structures is important for practical applications in environmental purification and solar energy conversion. We present here the fabric...Controlled synthesis of hierarchically assembled titanium dioxide （TiO2） nano- structures is important for practical applications in environmental purification and solar energy conversion. We present here the fabrication of interconnected TiO2 nanotubes as a macroscopic bulk material by using a porous carbon nanotube （CNT） sponge as a template. The basic idea is to uniformly coat an amorphous titania layer onto the CNT surface by the infiltration of a TiO2 precursor into the sponge followed by a subsequent hydrolysis process. After calcination, the CNTs are completely removed and the titania is simultaneously crystallized, which results in a porous macrostructure composed of interconnected anatase TiO2 nanotubes. The TiO2 nanotube macrostructures show comparable photocatalytic activities to commercial products （AEROXIDE TiO2 P25） for the degradation of rhodamine B （RhB）. Moreover, the TiO2 nanotube macrostructures can be settled and separated from water within 12 h after photocatalysis, whereas P25 remains suspended in solution after weeks. Thus the TiO2 nanotube macrostructures offer the advantage of easy catalyst separation and recycle and can be a promising candidate for wastewater treatment.展开更多
基金ACKNOWLEDGMENT This work was supported Science Foundation of China by the National Natural （No.20703042）.
文摘Titania-based composite catalysts were prepared through a sol-gel route employing multi-walled carbon nanotubes with different diameters. The materials were characterized using thermogravimetric analysis, nitrogen adsorption-desorption isotherm, powder X-ray diffraction, scanning electron microscopy, and diffuse reflectance UV-Vis absorption spectra. The application of the catalysts to photocatalytic degradation of phenol was tested under UV-Vis irradiation. A synergetic effect on phenol removal was observed in case of composite catalysts, which was evaluated in terms of apparent rate constant, total organic carbon removal and photonic efficiency.
文摘Titania coating of multi wall carbon nano tube(MWCNT) was carried out by sol-gel method in order to improve its photo catalytic properties.The effect of MWCNT/TiO_2 mass to volume ratio on adsorption ability,reaction rate and photo-catalytic removal efficiency of dibenzothiophene(DBT) from n-hexane solution was investigated using a 9 W UV lamp.The results show that the addition of nanotubes improves the photo-catalytic properties of TiO_2 by two factors;however,the DBT removal rate versus MWCNT content is found to follow a bimodal pattern.Two factors are observed to affect the removal rate of DBT and produce two optimum values for MWCNT content.First,large quantities of MWCNTs prevent light absorption by the solution and decrease removal efficiency.By contrast,a low dosage of MWCNT causes recombination of the electron holes,which also decreases the DBT removal rate.The optimum MWCNT contents in the composite are found to be 0.25 g and 0.75 g MWCNT per 80 m L of sol.
文摘In this work, the authors present a study of dye absorption in TiO2 doped with CNTs （carbon nanotubes）. Absorption decreases exponentially with the increase of CNTs in the film, while morphological characterization, conducted by SEM （scanning electron microscope） and TEM （transmission electron microscope） microscopes, suggests that this behavior is strongly related to morphological structure of grown films. For CNTs amounts greater than 1%, the authors observe the formation of CNTs clusters randomly distribute on TiO2 bulk, which strongly reduces the film porosity quenching the dye absorption. Comparison with optical properties of CNT/TiO2 filmstudied in the previous work, suggest that the best level of doping is with 0.5% of CNTs. FTIR （Fourier transform infrared spectroscopy） measurements conducted on a series of pristine and doped samples clearly indicate the absence of change in allotropic species of TiO2, while AFM （atomic force microscope） analysis indicates that the sample roughness strongly changes with doping, preventing the dye adsorption. Finally, measurements of cell efficiency indicate an increase of 5% in cells with 0.5% of CNT doping and a decrease for greater values.
文摘Controlled synthesis of hierarchically assembled titanium dioxide （TiO2） nano- structures is important for practical applications in environmental purification and solar energy conversion. We present here the fabrication of interconnected TiO2 nanotubes as a macroscopic bulk material by using a porous carbon nanotube （CNT） sponge as a template. The basic idea is to uniformly coat an amorphous titania layer onto the CNT surface by the infiltration of a TiO2 precursor into the sponge followed by a subsequent hydrolysis process. After calcination, the CNTs are completely removed and the titania is simultaneously crystallized, which results in a porous macrostructure composed of interconnected anatase TiO2 nanotubes. The TiO2 nanotube macrostructures show comparable photocatalytic activities to commercial products （AEROXIDE TiO2 P25） for the degradation of rhodamine B （RhB）. Moreover, the TiO2 nanotube macrostructures can be settled and separated from water within 12 h after photocatalysis, whereas P25 remains suspended in solution after weeks. Thus the TiO2 nanotube macrostructures offer the advantage of easy catalyst separation and recycle and can be a promising candidate for wastewater treatment.
