The magamp (magnetic amplifier) is widely used in power supplies due to its low cost, simplicity and other advan-tages. This paper discusses a novel application of the magamp in switching power supplies, where the mag...The magamp (magnetic amplifier) is widely used in power supplies due to its low cost, simplicity and other advan-tages. This paper discusses a novel application of the magamp in switching power supplies, where the magamp is used to regulate pulse width modulation (PWM) instead of power signal in the main circuit. This method extends the application of the magamp in power supplies, and makes it possible to further regulate control signal when PWMs have been generated. Based on this applica-tion, a new current-sharing (CS) scheme using the magamp is proposed, which uses a modified inner loop CS structure. In this scheme PWMs are generated by one main controller, and CS is achieved by regulating PWMs using a magamp in each module. Compared with traditional application of the magamp, the new CS scheme can be used in most topologies and only requires magamps of low power capacity. Then a test circuit of parallel power supply is developed, in which CS is achieved by a PWM regulator with the magamp. The proposed scheme is also used to upgrade an electroplate power to make it capable of paralleling supplies. Experimental results show that the proposed scheme has good CS performance.展开更多
In view of the low resolution and accuracy of traditional magnetometer,a method of microwave frequency modulation technology based on nitrogen-vacancy(NV)center in diamond for magnetic detection was proposed.The magne...In view of the low resolution and accuracy of traditional magnetometer,a method of microwave frequency modulation technology based on nitrogen-vacancy(NV)center in diamond for magnetic detection was proposed.The magnetometer studied can reduce the frequency noise of system and improve the magnetic sensitivity by microwave frequency modulation.Firstly,ESR spectra by sweeping the microwave frequency was obtained.Further,the microwave frequency modulated was gained through the mixed high-frequency sinusoidal modulation signal generated by signal generator.In addition,the frequency through the lock-in amplifier was locked,and the signal which was proportional to the first derivative of the spectrum was obtained.The experimental results show that the sensitivity of magnetic field detection can reach 17.628 nT/Hz based on microwave frequency modulation technology.The method realizes high resolution and sensitivity for magnetic field detection.展开更多
We have presented here a simple model of magnetic tunnel junction(MTJ)device and the proposed MTJ model is utilizedfor validation purpose and also to study its tunnel magneto-resistance(TMR)effect by both simulation a...We have presented here a simple model of magnetic tunnel junction(MTJ)device and the proposed MTJ model is utilizedfor validation purpose and also to study its tunnel magneto-resistance(TMR)effect by both simulation and experimentalmethod using an operational amplifier(OPAMP)based inverting amplifier.Experimental results substantiates both the simulatedand theoretical outcomes.展开更多
ELF （extremely low frequency） magnetic fields from power-line current influence the yield of CMOS foundry. The poor yield happens because of ELF magnetic fields inducing directly the measurement or process equipment...ELF （extremely low frequency） magnetic fields from power-line current influence the yield of CMOS foundry. The poor yield happens because of ELF magnetic fields inducing directly the measurement or process equipment for cutting-edge chips below 28 nm process. The equipments of electron microscopes, including SEM （scanning electron microscope）, TEM （transmission electron microscopy）, STEM （scanning transmission electron microscopy） and EBLS （electron beam lithography system） are very susceptible to ELF magnetic fields emanating from various electrical power sources outside of the building and within next generation CMOS foundry recommends a maximum of 0.3 mG. The active canceling method uses active coils with current sensing field via sensor and inducing man-made electromagnetic field to reduce the stray magnetic field. Unfortunately, the conventional system takes more time to products field because of parasitical capacitance and resistance in long coil. The longer canceling coil the system construct, the more time it takes. Besides, canceling system should spend more time on calibrating non-linear current amplifier through software design. This research designs simpler anti-electro-magnetic system instead of typical frame and develops one turn canceling coil structure to reduce delaying time. Several parallel cells generate field up to 23.81 mG controlled by MPU （micro processor unit）. This system decreases the power-line inducing filed below 0.3 mG.展开更多
基金Project (No. 50677063) supported by the National Natural Science Foundation of China
文摘The magamp (magnetic amplifier) is widely used in power supplies due to its low cost, simplicity and other advan-tages. This paper discusses a novel application of the magamp in switching power supplies, where the magamp is used to regulate pulse width modulation (PWM) instead of power signal in the main circuit. This method extends the application of the magamp in power supplies, and makes it possible to further regulate control signal when PWMs have been generated. Based on this applica-tion, a new current-sharing (CS) scheme using the magamp is proposed, which uses a modified inner loop CS structure. In this scheme PWMs are generated by one main controller, and CS is achieved by regulating PWMs using a magamp in each module. Compared with traditional application of the magamp, the new CS scheme can be used in most topologies and only requires magamps of low power capacity. Then a test circuit of parallel power supply is developed, in which CS is achieved by a PWM regulator with the magamp. The proposed scheme is also used to upgrade an electroplate power to make it capable of paralleling supplies. Experimental results show that the proposed scheme has good CS performance.
基金National Natural Science Foundation of China(Nos.51635011,61503346,51727808)National Science Foundation of Shanxi Province(No.201701D121080)
文摘In view of the low resolution and accuracy of traditional magnetometer,a method of microwave frequency modulation technology based on nitrogen-vacancy(NV)center in diamond for magnetic detection was proposed.The magnetometer studied can reduce the frequency noise of system and improve the magnetic sensitivity by microwave frequency modulation.Firstly,ESR spectra by sweeping the microwave frequency was obtained.Further,the microwave frequency modulated was gained through the mixed high-frequency sinusoidal modulation signal generated by signal generator.In addition,the frequency through the lock-in amplifier was locked,and the signal which was proportional to the first derivative of the spectrum was obtained.The experimental results show that the sensitivity of magnetic field detection can reach 17.628 nT/Hz based on microwave frequency modulation technology.The method realizes high resolution and sensitivity for magnetic field detection.
文摘We have presented here a simple model of magnetic tunnel junction(MTJ)device and the proposed MTJ model is utilizedfor validation purpose and also to study its tunnel magneto-resistance(TMR)effect by both simulation and experimentalmethod using an operational amplifier(OPAMP)based inverting amplifier.Experimental results substantiates both the simulatedand theoretical outcomes.
文摘ELF （extremely low frequency） magnetic fields from power-line current influence the yield of CMOS foundry. The poor yield happens because of ELF magnetic fields inducing directly the measurement or process equipment for cutting-edge chips below 28 nm process. The equipments of electron microscopes, including SEM （scanning electron microscope）, TEM （transmission electron microscopy）, STEM （scanning transmission electron microscopy） and EBLS （electron beam lithography system） are very susceptible to ELF magnetic fields emanating from various electrical power sources outside of the building and within next generation CMOS foundry recommends a maximum of 0.3 mG. The active canceling method uses active coils with current sensing field via sensor and inducing man-made electromagnetic field to reduce the stray magnetic field. Unfortunately, the conventional system takes more time to products field because of parasitical capacitance and resistance in long coil. The longer canceling coil the system construct, the more time it takes. Besides, canceling system should spend more time on calibrating non-linear current amplifier through software design. This research designs simpler anti-electro-magnetic system instead of typical frame and develops one turn canceling coil structure to reduce delaying time. Several parallel cells generate field up to 23.81 mG controlled by MPU （micro processor unit）. This system decreases the power-line inducing filed below 0.3 mG.
