期刊文献+
共找到9篇文章
< 1 >
每页显示 20 50 100
含铬的磷酸盐 被引量:1
1
作者 纪柱 《铬盐工业》 2005年第2期46-53,共8页
含铬磷酸盐包括磷酸铬、磷酸铝铬、磷酸铬铝镁、磷酸铬钙、磷酸铬铝钙、磷氯酸铬、磷铬酸钙等。
关键词 含铬酸盐 酸铬 酸铝铬 酸铬铝镁 酸铬钙 酸铬铝钙 氯酸铬 磷铬酸
下载PDF
硝酸预浸在阳极氧化膜封孔质量检测中的应用 被引量:3
2
作者 纪红 李永丰 《表面技术》 EI CAS CSCD 北大核心 2012年第6期125-127,共3页
阳极氧化膜封孔质量的好坏,会直接影响阳极氧化膜的使用寿命。硝酸预浸是欧洲标准中规定的外部建筑用铝合金阳极氧化膜封孔质量检测的仲裁方法,文中考察了硝酸预浸在封孔质量检测中的作用,结果表明:硝酸预浸有溶解氧化膜和扩孔的作用,... 阳极氧化膜封孔质量的好坏,会直接影响阳极氧化膜的使用寿命。硝酸预浸是欧洲标准中规定的外部建筑用铝合金阳极氧化膜封孔质量检测的仲裁方法,文中考察了硝酸预浸在封孔质量检测中的作用,结果表明:硝酸预浸有溶解氧化膜和扩孔的作用,在封孔质量检测中引入硝酸预浸,不仅严格了对封孔质量的要求,而且使得封孔质量的判别更为灵敏。 展开更多
关键词 硝酸预浸 封孔质量 阳极氧化膜 磷铬酸
下载PDF
铝阳极氧化膜不同封孔方法的耐腐蚀性能研究 被引量:7
3
作者 余祖孝 郝世雄 +2 位作者 王莹 左由兵 易伟 《轻合金加工技术》 CAS 北大核心 2007年第4期35-37,共3页
用电化学法、磷-铬酸质量检测法和金相电子显微镜,研究了6种封孔方法对铝阳极氧化膜耐腐蚀性能的影响。结果表明,都在最佳工艺条件下,硬脂酸封孔后的氧化膜是最耐腐蚀的,依次是硫酸镍封孔后的,重铬酸钾封孔后的,沸水封孔后的,醋酸镍封... 用电化学法、磷-铬酸质量检测法和金相电子显微镜,研究了6种封孔方法对铝阳极氧化膜耐腐蚀性能的影响。结果表明,都在最佳工艺条件下,硬脂酸封孔后的氧化膜是最耐腐蚀的,依次是硫酸镍封孔后的,重铬酸钾封孔后的,沸水封孔后的,醋酸镍封孔后的,耐蚀性能最差的是氟化镍常温冷封孔后的。 展开更多
关键词 铝阳极氧化膜 封孔方法 耐腐蚀性能 电化学方法 -铬酸
下载PDF
Phosphate film free of chromate, fluoride and nitrite on AZ31 magnesium alloy and its corrosion resistance 被引量:4
4
作者 崔学军 刘春海 +3 位作者 杨瑞嵩 李明田 林修洲 龚敏 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2012年第11期2713-2718,共6页
A phosphate solution free of chromate, fluoride and nitrite was prepared and an environment-friendly film was obtained on AZ31 magnesium alloy surface via the chemical deposition method. The morphology, composition, p... A phosphate solution free of chromate, fluoride and nitrite was prepared and an environment-friendly film was obtained on AZ31 magnesium alloy surface via the chemical deposition method. The morphology, composition, phase structure and its corrosion resistance were studied. The effects of film-forming temperature and free acid on corrosion resistance, microstructure and electrochemical behavior of the film were discussed. The results indicate that the corrosion resistance of AZ31 with the phosphate film was better than blank AZ31 substrate, which was most attributed to the great inhibitive action on the anodic dissolution and cathodic hydrogen evolution of the film. 展开更多
关键词 magnesium alloy AZ31 alloy phosphate conversion coating chromate-free film corrosion resistance anodicdissolution cathodic hydrogen evolution
下载PDF
铝合金阳极氧化膜封孔质量检验方法的对比研究 被引量:1
5
作者 尤媛 曲凤娇 +3 位作者 肖宝靓 曹阳 杨波 王复栋 《铝加工》 CAS 2019年第4期38-41,共4页
采用磷铬酸法、磷酸法和磷酸钼酸钠法对经过不同封孔工艺处理的6063-T6铝合金阳极氧化膜的封孔质量进行检测。结果表明,磷酸法和磷酸钼酸钠法与磷铬酸法的检测结果具有良好的对应关系。与磷铬酸法相比,磷酸法缺少了缓蚀剂,当裸露铝基体... 采用磷铬酸法、磷酸法和磷酸钼酸钠法对经过不同封孔工艺处理的6063-T6铝合金阳极氧化膜的封孔质量进行检测。结果表明,磷酸法和磷酸钼酸钠法与磷铬酸法的检测结果具有良好的对应关系。与磷铬酸法相比,磷酸法缺少了缓蚀剂,当裸露铝基体与阳极氧化膜面积比小于10%时,其失重质量比磷酸法偏高2mg/dm^2左右。由于磷酸对铝具有腐蚀性,因此,质量损失随着面积比的增大而变大。所以采用磷酸法进行检测时,应对裸露的铝基体进行密封后再进行试验。磷酸钼酸钠法与磷铬酸法之间的试验误差较小,基本都在±1mg/dm^2范围内,并且钼酸钠具有缓蚀剂的作用,与裸露铝基体面积的大小无关。用磷酸钼酸钠法替代磷铬酸法对铝合金阳极氧化膜封孔质量的评价具有很好的效果,而且更安全环保。 展开更多
关键词 6063-T6铝合金 阳极氧化膜 封孔质量 磷铬酸 酸法
下载PDF
Chromic-P32 phosphate treatment of implanted pancreatic carcinoma: Mechanism involved 被引量:8
6
作者 LuLiu Guo-ShengFeng +5 位作者 HongGao Guan-ShengTong YuWang WenGao YingHuang ChengLi 《World Journal of Gastroenterology》 SCIE CAS CSCD 2005年第14期2101-2108,共8页
AIM: To study the effects of chromic-P32 phosphate (32p colloids) interstitial administration in Pc-3 implanted pancreatic carcinoma, and investigate its anticancer mechanism.METHODS: Ninety-eight tumor bearing nude m... AIM: To study the effects of chromic-P32 phosphate (32p colloids) interstitial administration in Pc-3 implanted pancreatic carcinoma, and investigate its anticancer mechanism.METHODS: Ninety-eight tumor bearing nude mice werekilled at different time points after the injection of 32Pcolloids to the tumor core with observed radioactivity. The light microscopy, transmission electron microscopy (TEM) and immuno-histochemistry and flow cytometry were used to study the rates of tumor cell necrosis, proliferating cell nuclear antigen index, the micro vessel density (MVD). The changes of the biological response to the lymphatic transported 32p colloids in the inguinal lymph node (ILN) were dynamically observed, and the percentage of tumor cell apoptosis, and Apo2.7, caspase-3, Bcl-2, Baxrelated gene expression were observed too.RESULTS: The half-life of effective medication is 13 dafter injection of 32P colloids to the tumor stroma, in 1-6groups, the tumor cell necrosis rates were 20%, 45%,65%, 70%, 95% and 4%, respectively (F= 4.14-105.36, P<0.01). MVD were 38.5±4.0, 28.0±2.9, 17.0±2.9, 8.8±1.5,5.7±2.3 and 65.0±5.2 (t= 11.9-26.1, P<0.01), respectively.Under TEM fairly differentiated Pc-3 cells were found. Thirty days after medication, tumors were shrunk and dried with scabs detached, and those in control group increased in size prominently with plenty of hypodermic blood vessels. In all animals the ILN were enlarged but in medicated animals they appeared later and smaller than those in control group. The extent of irradiative injury in ILN was positively correlated to the dosage of medication. Typical tumor cell apoptosis could be found under TEM inanimals with intra-tumoral injection of low dosed 32P colloids. The peak of apoptosis occurred in 2.96 MBq group and 24 h after irradiation. In the course of irradiationinduced apoptosis, the value of Bcl-2/Bax was down regulated; Apo2.7 and caspase-3 protein expression were prominently increased dose dependently. CONCLUSION: 32p colloids intra-tumor injection having prominent anticancer effectiveness may reveal the ability of promoting cell differentiation. The low dose 32P colloids may induce human pancreatic carcinoma Pc-3 implanted tumor cell apoptosis; Apo2.7, caspase-3, Bcl-2 and Bax protein participated in regulating the process of irradiation induced cell apoptosis. 展开更多
关键词 Chromic-P32 phosphate Pancreatic carcinoma
下载PDF
Modelling and Fixed Bed Column Adsorption of Cr(Ⅵ) onto Orthophosphoric Acid-activated Lignin 被引量:3
7
作者 Ahmad B.Albadarin Chirangano Mangwandi +3 位作者 Ala'a H.Al-Muhtaseb Gavin M.Walker Stephen J.Allen Mohammad N.M.Ahmad 《Chinese Journal of Chemical Engineering》 SCIE EI CAS CSCD 2012年第3期469-477,共9页
The advantage of using an available and abundant residual biomass, such as lignin, as a raw material for activated carbons is that it provides additional economical interest to the technical studies. In the current in... The advantage of using an available and abundant residual biomass, such as lignin, as a raw material for activated carbons is that it provides additional economical interest to the technical studies. In the current investigation, a more complete understanding of adsorption of Cr(VI) from aqueous systems onto HaPO4-acid activated lignin has been achieved via microcolumns, which were operated under various process conditions. The practice of using microcolumn is appropriate for defining the adsorption parameters and for screening a large number of poten- tial adsorbents. The effects of solution pH (2-8), initial metal ion concentration (0.483-1.981 mmol.L-1), flow rate (1.0-3.1 cm3-min-1), ionic strength (0.01-0.30 mmol-L-1) and adsorbent mass (0.11 0.465 g) on Cr(VI) adsorption were studied by assessing the microcolmnn breakthrough curve. The microcolumn data were fitted by the Thomas model, the modified Dose model and the BDST model. As expected, the adsorption capacity increased with initial Cr(VI) concentration. High linear flow rates, pH values and ionic strength led to early breakthrough of Cr(VI). The model constants obtained in this study can be used for the design of pilot scale adsorption process. 展开更多
关键词 activated carbon LIGNIN hexavalent chromium ADSORPTION fixed bed column
下载PDF
简单蚀刻法制备具有可控高度的金属纳米线阵列 被引量:2
8
作者 陈东 宋国君 +3 位作者 彭智 佘希林 李建江 韩萍 《功能材料与器件学报》 EI CAS CSCD 北大核心 2007年第4期306-310,共5页
采用多孔阳极氧化铝(AAO)作为模板,运用电化学沉积法在模板的微孔中组装金属N i纳米线,然后用磷铬酸蚀刻表层AAO模板,暴露出规整有序、具有可控长度的N i纳米线阵列。分别用SEM、TEM与SAED对N i纳米线阵列进行了表征。研究了蚀刻时间与... 采用多孔阳极氧化铝(AAO)作为模板,运用电化学沉积法在模板的微孔中组装金属N i纳米线,然后用磷铬酸蚀刻表层AAO模板,暴露出规整有序、具有可控长度的N i纳米线阵列。分别用SEM、TEM与SAED对N i纳米线阵列进行了表征。研究了蚀刻时间与AAO模板质量的减少及暴露出来的N i纳米线阵列长度之间的关系。结果表明,磷铬酸是较NaOH溶液更为温和有效的AAO模板蚀刻剂,通过控制模板溶解时间,可以实现对裸露于AAO模板外纳米线长度的精细有效控制。该蚀刻方法普遍适用于以AAO为模板所制得的准一维纳米阵列结构。 展开更多
关键词 纳米线阵列 电沉积 AAO 蚀刻 磷铬酸
原文传递
阳极氧化膜封孔质量评定方法探讨 被引量:1
9
作者 周鹏 李扬 +1 位作者 陈颖欣 陈文 《物理测试》 CAS 2019年第3期11-13,共3页
目前中国评价阳极氧化膜封孔质量的仲裁方法是硝酸预浸磷铬酸法。从环保的角度出发,为了实现无铬化,采用磷酸法和磷铬酸法进行对比试验,并研究硝酸预浸在封孔质量检测中的作用。结果表明,采用磷酸法代替磷铬酸法具有局限性,只有在封孔... 目前中国评价阳极氧化膜封孔质量的仲裁方法是硝酸预浸磷铬酸法。从环保的角度出发,为了实现无铬化,采用磷酸法和磷铬酸法进行对比试验,并研究硝酸预浸在封孔质量检测中的作用。结果表明,采用磷酸法代替磷铬酸法具有局限性,只有在封孔质量良好时,两种方法的检测结果才具有较好的相关性。在封孔质量检测中引入硝酸预浸,会加速阳极氧化膜的腐蚀,使得失重值增大。 展开更多
关键词 封孔质量 磷铬酸 酸法 硝酸预浸
原文传递
上一页 1 下一页 到第
使用帮助 返回顶部