用离子镀法镀超硬质膜的提示

在模具和刀具的表面镀上超硬质膜,以提高其硬度、耐蚀性和耐磨损性。目前已有多种镀膜方式,如PVD法(真空蒸发法、溅射法、离子镀法)、CVD法,湿式镀法等,其中用离子镀法镀超硬质膜最引人注目(参见图1)。 1964年由美国的MATTOX开发的这项技术,在70年代又作了各种改进,进入80年代后才逐渐确立为生产技术。

A method for calculation of ion distribution in reaction system forming hydroxide

A formula was proposed to calculate the distribution of metal ions quantitatively in chemical reaction system forming hydroxide where precipitation and complex are formed together. The effects of some factors on formation of precipitation and complex were investigated, and the corresponding precipitation rates of zinc, iron （III）, aluminum, copper and magnesium were calculated. As a result, it shows that the proposed formula is reliable. By the proposed formula, the existence state of metal ions in hydroxides reaction system with any metal ions can be well described and the effects of some factors on the distribution of metal ions were determined.

Chemical looping partial oxidation over FeWOx/SiO2 catalysts

This paper describes the design of a FeWOx-based oxygen carrier for the chemical partial oxidation of methane(CLPOM).Thermodynamic screening and kinetic analyses both forecast the FeWOx-based oxygen carrier as a promising candidate for the production of syngas.The total methane conversion and syngas yield can be dramatically increased with this catalyst compared to the case with the unmodified WO3/SiO2,thereby enabling CLPOM with 62%methane conversion,93%CO gas-phase selectivity,94%H2 selectivity,and a 2.4 H2/CO ratio.The catalyst has the advantages of high availability of lattice oxygen to oxidize carbonaceous intermediates in time,together with the formation of an Fe-W alloy to promote the surface reaction.Consequently,it demonstrates excellent catalytic performance with no catalyst deactivation at 900°C and 1 atm.The excellent structural stability plays an essential role in CLPOM.As revealed via XPS and ICP,the phase segregation has not been observed due to the strong interaction between Fe and W,which resulted in the formation of the Fe-W alloy during the reduction processes and the match between the ion oxidation rates of the Fe and W ions in the oxidation stage.The results provide fundamental information on the reaction mechanism of FeWOx/SiO2,and present it as a promising candidate for CLPOM.

Acid Release from an Acid Sulfate Soil Sample Under Successive Extractions with Different Extractants

An acid sulfate soil sample was successively extracted with deionized water, 1 mol L-1 KCl and 0.000 5 mol L-l Ca(OH)2 solutions. The results showed that only very small amounts of acidity were extracted by deionized water, possibly through slow jarosite hydrolysis. Acid release through jarosite hydrolysis was greatly enhanced by Ca(OH)2 extraction at the expense of the added OH- being neutralized by the acid released. Successive extraction of the sample with KCl removed the largest amounts of acidity from the sample. However, it is likely that the major form of acidity released by KCl extraction was exchangeable acidity. The results also show the occurrence of low or non charged Al and Fe species in water and Ca(OH)2 extracts after first a few extractions. It appears that such a phenomenon was related to a decreasing EC value with increasing number of extractions.

Effects of electrical parameters and their interactions on plasma electrolytic oxidation coatings on aluminum substrates

Based on orthogonal experiments,the effects of voltage,frequency,duty ratio and their interactions on the thickness and corrosion resistance of coatings prepared by plasma electrolytic oxidation(PEO)on aluminum in an alkaline silicate-containing electrolyte were investigated.The thicknesses of these coatings were obtained by measuring their cross-section using Image J software.Their corrosion resistances were evaluated in HCl and NaCl media through spot test and electrochemical test.The results show that the experimental design of this study is the key to investigate the interactions among these electrical parameters.Additionally,not only each independent factor,but also their interactions exhibit a remarkable influence on the coatings.The combination of high voltage,low frequency and large duty ratio significantly increases the coating thickness and content of the corrosion resistance phase,and thus improves the corrosion resistance of the coating in HNO3 medium.Conversely,the coating possessing the densest microstructure and best corrosion resistance in NaCl medium is obtained when low voltage and high frequency match with a small duty ratio.

Optimization on cationic liposome-mediated cell transfection of plasmid DNA

Objective:The development of gene carriers for efficient gene delivery into cells has attracted growing attention in recent years.The aim of this study was to achieve a better outcome of AAV-293 cells transfection by plasmid DNA.Methods:We studied the optimal condition for higher efficiency of cationic lipid-mediated cell transfection.Four experimental groups were set.Plasmid DNA and liposome were mixed in each groups at different ratios(μg:μL),1:2.5,1:3.5,1:4.0 and 1:5.0,respectively.LacZ gene functioned as reporter gene,measuring the transfection efficiency of the four groups using the method of X-gal staining.Results:When the ratio was 1:3.5,the cell transfection rate was the highest.While the ratio of 1:2.5 recommended by product manual achieve the lowest transfection rate.Their difference had statistical significance.Conclusion:In order to obtain a higher transfection efficiency,optimization on conditions of the ratio of plasmid DNA to liposome is necessary in cell transfection.

Degradation of aniline by Fe^(2+)-activated persulfate oxidation at ambient temperature

The aniline degradation by persulfate activated with ferrous ion (Fe2+ ) was investigated in batch reactor at ambient temperature. The experimental factors in aqueous solutions including persulfate concentration, Fe2+ concentration, pH and ionic strength level were discussed. It is demonstrated that, aniline degradation rate increases with increasing persulfate concentration, but much more ferrous ion inhibits the aniline degradation. When the aniline concentration is 0.10 mmol/L, the maximum aniline degradation occurs at the S2O82- to Fe2+ molar ratio of 250/5 at pH 7.0. In the pH range of 5.0-8.5, increasing pH causes higher aniline degradation. What's more, the increase of ionic strength in solution causes inhibiting in the reaction. Produced intermediates during the oxidation process were identified using gas chromatography-mass spectrometry (GC-MS) technology. And degradation pathways of aniline were also tentatively proposed.

Influence of silicate anions structure on desilication in silicate-bearing sodium aluminate solution

The structural changes of silicate anions in the desilication process with the addition of calcium hydrate alumino-carbonate were studied by measuring Raman spectra, infrared spectra and corresponding second derivative spectra. The results show that the desilication ratio in the solution prepared by the addition of sodium silicate(solution-SS) is much greater than that in the solution by the addition of green liquor(solution-GL), and low alumina concentration in the sodium aluminate solutions facilitates the desilication process. It is also shown that alumino-silicate anions in the solution-GL, and Q^3 polymeric silicate anions in solution-SS are predominant, respectively. In addition, increasing the concentration of silica favors respectively the formation of the alumino-silicate or the Q^3 silicate anions in the solution-GL or the solution-SS. Therefore, it can be inferred that the low desilication ratio in the silicate-bearing aluminate solution is mainly attributed to the existence of alumino-silicate anions.

Effect of chelating agent on oxidation rate of aniline in ferrous ion activated persulfate system at neutral pH

In the interest of accelerating aniline degradation, Fe2+ and chelated Fe2+ activated persulfate oxidations were investigated in neutral pH condition. Three kinds of chelating agents were selected including citric acid, oxalic acid and ethylenediamine tetraaceatate(EDTA) to maintain available Fe2+. The results indicate that the concentration of chelating agent and ferrous ion didn't follow a linear relationship with the degradation rate of aniline. A 1/1 ratio of chelating agent/Fe2+ results in a higher degradation rate compared to the results by other ratios. The oxidation enhancement factor using oxalic acid was found to be relatively low. In contrast, citric acid is more suitable chelating agent in the ferrous iron activated persulfate system and aniline exhibits a highest degradation with a persulfate/Fe2+/citric acid/aniline molar ratio of 50/25/25/1 compared to other molar ratios.

Structures of Stoichiometric Sodium Oxide Cluster Cations Studied by Ion Mobility Mass Spectrometry

Structures of stable compositions of sodium oxide cluster cations (NanOm+,n≤11) have been investigated by ion mobility mass spectrometry. Stoichiometric compositions series, Na(Na2O)(n-1)/2^+(n=3, 5, 7, 9, and 11), were observed as stable composition series, and NaO(Na2O)(n-1)/2^+ series (n=5, 7, 9, and 11) were observed as secondary stable series in the mass spectra. To assign the structures of these cluster ion series, collision cross sections between the ions and helium buffer gas were determined experimentally from the ion mobility measurements. Theoretical collision cross sections were also calculated for optimized structures of these compositions. Finally, the structures of Na(Na2O)(n-1)/2^+ and NaO(Na2O)(n-1)/2^+ were assigned to those having similar structural frames for each n except for n=9. All bonds in the assigned structures of Na(Na2O)(n-1)/2^+ were between sodium and oxygen. On the other hand, there was one O-O bond in addition to Na-O bonds in NaO(Na2O)(n-1)/2^+. This result indicates that NaO(Na2O)(n-1)/2^+ have a peroxide ion (O22-) as a substitute for an oxide ion (O2-) of Na(Na2O)(n-1)/2^+. As a result, both stable series, Na(Na2O)(n-1)/2^+ and NaO(Na2O)(n-1)/2^+, are closed-shell compositions. These closed-shell characteristics have a strong influence on the stability of sodium oxide cluster cations.

Morphology of Polyvinylidene Fluoride Based Gel Polymer Electrolytes

Two series of polyvinylidene fluoride (PVDF) based gel polymer electrolytes, with different LiClO 4 or propylene carbonate (PC) content, were prepared and analyzed by infrared spectrometer, differential scanning calorimetry, scanning electron microscope and complex impedance spectrometer. The results show that there are great interactions between PVDF, PC and lithium cations. Both LiClO 4 and PC content lead to evident change of the morphology of the gel polymer electrolytes. The content of LiClO 4 and PC also influences the ionic conductivity of the samples, and an ionic conductivity of above 10 -3 S·cm -1 can be reached at room temperature.

The effect of transition metal ions (M^(2+)=Mn^(2+),Ni^(2+),Co^(2+),Cu^(2+)) on the chemical synthesis polyaniline as counter electrodes in dye-sensitized solar cells

The effect of transition metal ions(M^(2+)=Mn^(2+),Ni^(2+),Co^(2+),Cu^(2+)) on the chemical synthesis of polyaniline(PANI) used as a platinum-free counter electrode(CE) in dye-sensitized solar cells(DSSCs) was investigated.PANI was synthesized by co-polymerization of aniline in the presence of different transition metal ions by using potassium dichromate in acidic medium. It was found that the ion doping of PANI showed a certain catalytic activity for the regeneration of traditional iodide/triiodide(I^-/I_3^-) redox couples. The power conversion efficiency(η) of PANI CEs doped with Mn^(2+),Ni^(2+),Co^(2+) (4.41%, 2.36% and 2.10%, respectively) were higher than 1.94%, the value measured for PANI CE without doping. Doping with Cu^(2+)decreased the power conversion efficiency of PANI CE(PANI-Cu^(2+) η = 1.41%). The electrical properties of the PANI, PANI-Ni^(2+), PANI-Co^(2+),PANI-Mn^(2+) and PANI-Cu^(2+) were studied by cyclic voltammetry(CV), impedance(EIS), and Tafel polarization curve. The experimental results confirmed that PANI was affected by the doping of different transition metal ions(M^(2+)=Mn^(2+),Ni^(2+),Co^(2+),Cu^(2+)). These results indicate a potential application of ion doped PANI as counter electrode in cost-effective DSSCs.

Transport hindrances with electrodialytic recovery of citric acid from solution of strong electrolytes

Electrodialytic （ED） recovery of citric acid （CA） in the presence/absence of strong electrolytes （NaCl, CaCl2 and Feel3） was separately analyzed under different process conditions. Recovery effectiveness was quantitatively estimated from current efficiency values. Efficiency attained optimum value with both flow rate and potential applied, while a monotonic rise was noted with temperature which got lowered beyond 0.1 tool. L 1 feed concentration. 40% drop in efficiency was recorded in the presence of strong electrolytes （Noel, CaCl2 and Feel3） in feed relative to their presence in concentrate. Severe transport hindrance and efficiency loss were attributed to adsorption and allied physicochemical changes occurred with anion/cation exchange membranes （AEM/CEM） and these were confirmed through contact angle/Chronopotentiometry/AFM/EDX. Sluggish potential rise （Galvanostatic mode） in Chronopotentiometric analysis indicated diffusion limiting transport of organic acids influenced AEM resistance. XRD and EDX analysis indicated the presence of salt hydrates/ions （Ca2＋/Fe3＋） over CEM justifying the resistance buildup due to adsorption of multivalent metal ion（s） and salts.

Research of the Purifying of Welding Fume on the Spot with Corona Plasma

The welding fume has significant effects on the weld workers＇ health. In order to overwhelm the shortcomings of the control measures of the welding fume, the research of the purifying of welding fume on the spot was carried out. The purifying device was designed. The relationship between the corona discharge voltage and the purifying efficiency was investigated through experiments with different needle electrode numbers, different ring electrode numbers and different needle-plate distances. The results show that 5-needle double-ring electrode has the best efficiency; the purifying efficiency is increase with the lessening of the needle-plate distance and the increase of the discharge voltage. Using 5-needle double-ring electrode, the purifying efficiency reaches its maximum value 97.9% while the needle-plate distance is 6 cm, the discharge voltage is -35 kV. The purifying device has an excellent purifying effect on the welding fume.

Leaching Phenomena of Antifouling Agents from Ships＇ Hull Paints

The effects ofpH, dissolved ion content and relative water velocity on the release rate of an antifouling agent, cuprous oxide, from ships＇ hull paint have been investigated by rotating cylinder tests. Additionally, test paint panels were attached to a vessel and recovered after a certain period of voyage for the validation of the laboratory tests. In the initial period, the release rates are influenced by pH, dissolved ion content and water velocity, but once after a certain period of test, those effects become less significant. These phenomena can be explained when the paint film is fresh, the rate is controlled by chemical reaction, the surface and/or diffusion layer in the water phase governs the rate. After the antifouling substance in the paint film leached out from the near-surface region, a diffused layer （leached layer）, that has little antifouling agent remained, is formed at the surface of the coating, and the diffusion in that layer can be a rate-determining process. The development of the leached layer is affected by a balance between the leaching rate of the antifouling ingredient and paint resin determined by the chemical properties and speed of the water. Thus, the leaching rates of antifouling agents are affected by the history of the paint in the water.

Electrolytes enriched by potassium perfluorinated sulfonates for lithium metal batteries

Lithium(Li) metal is widely considered as a promising anode for next-generation lithium metal batteries(LMBs) due to its high theoretical capacity and lowest electrochemical potential. However, the uncontrollable formation of Li dendrites has prevented its practical application. Herein, we propose a kind of multifunctional electrolyte additives(potassium perfluorinated sulfonates) from the multi-factor principle for electrolyte additive molecular design(EDMD) view to suppress the Li dendrite growth. The effects of these additives are revealed through experimental results, molecular dynamics simulations and firstprinciples calculations. Firstly, K^(+)can form an electrostatic shield on the surface of Li anode to prevent the growth of Li dendrites. Secondly, potassium perfluorinated sulfonates can improve the activity of electrolytes as co-conductive salts, and lower the electro-potential of Li nucleation. Thirdly, perfluorinated sulfonate anions not only can change the Li^(+)solvation sheath structure to decrease the desolvation energy barrier and increase the ion migration rate, but also can be partly decomposed to form the superior solid electrolyte interphase(SEI). Benefited from the synergistic effects, an outstanding cycle life over250 h at 1 m A cm^(-2) is achieved in symmetric Li||Li cells. In particular, potassium perfluorinated sulfonate additives(e.g., potassium perfluorohexyl sulfonate, denoted as K+PFHS) can also contribute to the formation of high-quality cathode electrolyte interphase(CEI). As a result, Li||LiNi_(0.6)Mn_(0.2)Co_(0.2)O_(2) full cells exhibit significantly enhanced cycling stability. This multi-factor principle for EDMD offers a unique insight on understanding the electrochemical behavior of ion-type electrolyte additives on both the Li metal anode and high-voltage cathode.

Electrical Characteristics and Reliability of Ultra-Thin Gate Oxides (<2nm) with Plasma Nitridation

MMT （modified magnetron typed） plasma nitridation and NO anneal are used to treat ultra-thin gate oxides in MOSFETs （metal-oxide-semiconductor field effect transistors）. Dual-peak and single-peak N distributions are formed after nitridation. The dual-peak N distribution shows excellent electrical properties and superior reliability in terms of drain current,channel carrier mobility, and TDDB characteristics. The results indicate a means to extend silicon oxynitride as a promising gate dielectric for developing ultralarge scale integrated （ULSI） technology.

Comprehensive screening and selection of okra (Abelmoschus esculentus) germplasm for salinity tolerance at the seedling stage and during plant ontogeny

The okra germplasm was screened for salinity tolerance at the seedling stage and during plant ontogeny. Substantial variation existed in okra for salinity tolerance at the seedling stage. An 80 mmol/L NaCI concentration was suitable for discriminating tolerant and non-tolerant okra genotypes. The pooled ranking of the genotypes, based on individual rankings for each trait （root and shoot length, germination percentage, and relative Na^＋ and K%＋） in individual NaCI concentrations, was effective for selecting tolerant genotypes. Genotypes selected at the seedling stage maintained their tolerance to NaCI during plant ontogeny, suggesting that screening of the germplasm entries and advanced breeding materials for salt tolerance at the seedling stage is effective. Among 39 okra genotypes, five were identified as the most tolerant genotypes and showed potential for use in breeding programs that focus on the development of salt-tolerant, high-yield okra cultivars.

Towards the gemini cation anion exchange membranes by nucleophilic substitution reaction

As a critical component of alkaline fuel cells, anion exchange membranes determine the energy efficiency, output power density and the long term stability. Recently, the anion exchange membranes with gemini-cation side chains exhibit superior ion conductivity due to their good nanophase separation. However, the costly and complicated synthesis limits their scaling up and commercialization. To address this problem, a convenient synthetic procedure under mild conditions is well developed. A tertiary amine precursor is introduced onto the polymer by the nucleophilic substitution reaction to avoid the conventional chloro/bromo-methylation. Followed by a simple Menshutkin reaction with 6- bromo-N,N,N-trimethylhexan-1-am inium bromide, the polym er electrolytes are obtained in a high yield. The resulting anion exchange membranes with high conductivity, good fuel cell performance and restricted swelling suggest the potential for the application in fuel cell devices.

Waste to wealth:Defect-rich Ni-incorporated spent LiFePO_(4)for efficient oxygen evolution reaction

The development of efficient strategies to recycle lithium-ion battery(LIB)electrode materials is an important yet challenging goal for the sustainable management of battery waste.This work reports a facile and economically efficient method to convert spent cathode material,LiFePO_(4),into a high-performance NiFe oxy/hydroxide catalyst for the oxygen evolution reaction(OER).Herein,Ni-LiFePO_(4)is synthesized via the wetness impregnation method and further evolves into defect-rich NiFe oxy/hydroxide nanosheets during the OER.The introduction of the Ni promoter together with in situ evolution strengthens the electronic interactions among the metal sites and creates an abundance of defects.Experimentally,the evolved Ni-LiFePO_(4)delivers a low overpotential of 285 mV at 10 mA cm-^(2)and a small Tafel slope of 45 mV dec^(-1),outperforming pristine LiFePO_(4)and is even superior to the benchmark catalyst RuO_(2).Density functional theory(DFT)calculations reveal that the introduction of Ni effectively activates Fe sites by optimizing the free energy of the*OOH intermediate and that the abundance of oxygen defects facilitates the oxygen desorption step,synergistically enhancing the OER performance of LiFePO_(4).As a green and versatile method,this is a new opportunity for the scalable fabrication of excellent electrocatalysts based on spent cathode materials.