Based on the theory of unsteady hydrodynamic lubrication and relevant mathematic and physical methods, a basic model was developed to analyze the unsteady lubrication film thickness, pressure stress and friction stres...Based on the theory of unsteady hydrodynamic lubrication and relevant mathematic and physical methods, a basic model was developed to analyze the unsteady lubrication film thickness, pressure stress and friction stress in the work zone in strip rolling. The distribution of pressure stress and friction stress in the work zone was obtained. A numerical simulation was made on a 1850 cold rolling mill. The influence of back tension stress and reduction on the distribution of pressure stress and friction stress between the roll gaps was qualitatively analyzed by numerical simulation. The calculated results indicate that the higher the back tension, the lower the pressure stress and the friction stress in the work zone, and the largest friction stresses are obtained at the inlet and outlet edges. The pressure and friction gradients are rather small at high back tension. The pressure-sensitive lubricant viscosity increases exponentially with the increase of pressure. The unsteady lubrication phenomenon in the roll bite is successfully demonstrated.展开更多
In order to explain the mechanism for gas outburst, the process of evolving fractures in coal seams is described using system dynamics with variable boundaries. We discuss the failure modes of coal containing gas and ...In order to explain the mechanism for gas outburst, the process of evolving fractures in coal seams is described using system dynamics with variable boundaries. We discuss the failure modes of coal containing gas and then established the flow rules after failure. The condition under which states of deformation convert is presented and the manner in which these convert is proposed. In the end, the process of gas outbursts is explained in detail. It shows that a gas outburst is a process in which the boundaries of coal seams are variable because of coal failure. If the fractures are not connected or even closed owing to coal/rock stress, fractured zones will retain a certain level of carrying capacity because of the self-sealing gas pressure. When the accumulation of gas energy reaches its limit, coal seams will become unstable and gas outbursts take place.展开更多
An analysis of the stability of large-diameter circular tunnels and ground settlement during tunnelling by a pressurized shield was presented. An innovative three-dimensional translational multi-block failure mechanis...An analysis of the stability of large-diameter circular tunnels and ground settlement during tunnelling by a pressurized shield was presented. An innovative three-dimensional translational multi-block failure mechanism was proposed to determine the face support pressure of large-shield tunnelling. Compared with the currently available mechanisms, the proposed mechanism has two unique features:(1) the supporting pressure applied to the tunnel face is assumed to have a non-uniform rather than uniform distribution, and(2) the method takes into account the entire circular excavation face instead of merely an inscribed ellipse. Based on the discrete element method, a numerical simulation of the Shanghai Yangtze River Tunnel was carried out using the Particle Flow Code in two dimensions. The immediate ground movement during excavation, as well as the behaviour of the excavation face, the shield movement, and the excavated area, was considered before modelling the excavation process.展开更多
Unsteady cavitating flow is extremely complicated and brings more serious damages and unignorable problems compared with steady cavitating flow.CFD has become a practical way to model cavitation;however,the popularly ...Unsteady cavitating flow is extremely complicated and brings more serious damages and unignorable problems compared with steady cavitating flow.CFD has become a practical way to model cavitation;however,the popularly used full cavitation model cannot reflect the pressure-change that the bubble experiences during its life path in the highly unsteady flow like cloud cavitating.Thus a dynamic cavitation model(DCM)is proposed and it has been considered to have not only the first-order pressure effects but also zero-order effect and can provide greater insight into the physical process of bubble producing,developing and collapsing compared to the traditional cavitation model.DCM has already been validated for steady cavitating flow,and the results were reported.Furthermore,DCM is designed and supposed to be more accurate and efficient in modeling unsteady cavitating flow,which is also the purpose of this paper.The basic characteristic of the unsteady cavitating flow,such as the vapor volume fraction distribution and the evolution of pressure amplitude and frequency at different locations of the hydrofoil,are carefully studied to validate DCM.It is found that not only these characteristics mentioned above accord well with the experimental results,but also some detailed transient flow information is depicted,including the re-entrant jet flow that caused the shedding of the cavity,and the phenomenon of two-peak pressure fluctuation in the vicinity of the cavity closure in a cycle.The numerical results validate the capability of DCM for the application of modeling the complicated unsteady cavitating flow.展开更多
基金Project(51175133)supported by the National Natural Science Foundation of China
文摘Based on the theory of unsteady hydrodynamic lubrication and relevant mathematic and physical methods, a basic model was developed to analyze the unsteady lubrication film thickness, pressure stress and friction stress in the work zone in strip rolling. The distribution of pressure stress and friction stress in the work zone was obtained. A numerical simulation was made on a 1850 cold rolling mill. The influence of back tension stress and reduction on the distribution of pressure stress and friction stress between the roll gaps was qualitatively analyzed by numerical simulation. The calculated results indicate that the higher the back tension, the lower the pressure stress and the friction stress in the work zone, and the largest friction stresses are obtained at the inlet and outlet edges. The pressure and friction gradients are rather small at high back tension. The pressure-sensitive lubricant viscosity increases exponentially with the increase of pressure. The unsteady lubrication phenomenon in the roll bite is successfully demonstrated.
基金financial support from the National Basic Research Program of China (No.2005CB221500)the National Natural Science Foundation of China (Nos.50534049,50674087 and 50974107)the Natural Science Foundation of Jiangsu Province (No.BK2007029)
文摘In order to explain the mechanism for gas outburst, the process of evolving fractures in coal seams is described using system dynamics with variable boundaries. We discuss the failure modes of coal containing gas and then established the flow rules after failure. The condition under which states of deformation convert is presented and the manner in which these convert is proposed. In the end, the process of gas outbursts is explained in detail. It shows that a gas outburst is a process in which the boundaries of coal seams are variable because of coal failure. If the fractures are not connected or even closed owing to coal/rock stress, fractured zones will retain a certain level of carrying capacity because of the self-sealing gas pressure. When the accumulation of gas energy reaches its limit, coal seams will become unstable and gas outbursts take place.
基金Project(41202220)supported by the National Natural Science Foundation of ChinaProject(20120022120003)supported by the Research Fund for the Doctoral Program of Higher Education,China+1 种基金Project(2652012065)supported by the Fundamental Research Funds for the Central Universities of ChinaProject(2013006)supported by the Research Fund for Key Laboratory on Deep GeoDrilling Technology from the Ministry of Land and Resources of China
文摘An analysis of the stability of large-diameter circular tunnels and ground settlement during tunnelling by a pressurized shield was presented. An innovative three-dimensional translational multi-block failure mechanism was proposed to determine the face support pressure of large-shield tunnelling. Compared with the currently available mechanisms, the proposed mechanism has two unique features:(1) the supporting pressure applied to the tunnel face is assumed to have a non-uniform rather than uniform distribution, and(2) the method takes into account the entire circular excavation face instead of merely an inscribed ellipse. Based on the discrete element method, a numerical simulation of the Shanghai Yangtze River Tunnel was carried out using the Particle Flow Code in two dimensions. The immediate ground movement during excavation, as well as the behaviour of the excavation face, the shield movement, and the excavated area, was considered before modelling the excavation process.
基金supported by the National Natural Science Foundation of China(Grant No.51276157)Zhejiang Provincial Natural Science Foundation(Grant No.LY12E060026)
文摘Unsteady cavitating flow is extremely complicated and brings more serious damages and unignorable problems compared with steady cavitating flow.CFD has become a practical way to model cavitation;however,the popularly used full cavitation model cannot reflect the pressure-change that the bubble experiences during its life path in the highly unsteady flow like cloud cavitating.Thus a dynamic cavitation model(DCM)is proposed and it has been considered to have not only the first-order pressure effects but also zero-order effect and can provide greater insight into the physical process of bubble producing,developing and collapsing compared to the traditional cavitation model.DCM has already been validated for steady cavitating flow,and the results were reported.Furthermore,DCM is designed and supposed to be more accurate and efficient in modeling unsteady cavitating flow,which is also the purpose of this paper.The basic characteristic of the unsteady cavitating flow,such as the vapor volume fraction distribution and the evolution of pressure amplitude and frequency at different locations of the hydrofoil,are carefully studied to validate DCM.It is found that not only these characteristics mentioned above accord well with the experimental results,but also some detailed transient flow information is depicted,including the re-entrant jet flow that caused the shedding of the cavity,and the phenomenon of two-peak pressure fluctuation in the vicinity of the cavity closure in a cycle.The numerical results validate the capability of DCM for the application of modeling the complicated unsteady cavitating flow.
