期刊文献+
共找到10篇文章
< 1 >
每页显示 20 50 100
蛋白乳化液稳定性影响因素的研究进展 被引量:1
1
作者 郭庆 木泰华 《食品工业科技》 CAS CSCD 北大核心 2010年第12期389-392,共4页
蛋白质是一种具有表面活性的化合物。被蛋白覆盖的油滴的性质(粒径、表面电荷、界面吸附蛋白浓度等)是决定乳化液稳定性的重要因素。本文综述了乳化液滴性质影响蛋白乳化液稳定性的研究进展,并展望了这一领域未来发展的趋势。
关键词 乳化液稳定性 影响因素 乳化液滴性质 机理
下载PDF
三聚磷酸钠对牛乳蛋白乳化液热稳定性的影响 被引量:2
2
作者 于鹏 孙克杰 +1 位作者 苏米亚 陆怡 《乳业科学与技术》 2008年第3期107-109,共3页
以脱脂奶、稀奶油和脱盐乳清粉为原料配制的牛乳蛋白乳化液来模仿婴儿配方食品,研究了在140℃时乳化液热稳定性与pH值的关系以及三聚磷酸钠对乳化液热稳定性的影响,乳化液的热变性时间(HCT)受pH值变化影响显著,添加三聚磷酸钠可以显著... 以脱脂奶、稀奶油和脱盐乳清粉为原料配制的牛乳蛋白乳化液来模仿婴儿配方食品,研究了在140℃时乳化液热稳定性与pH值的关系以及三聚磷酸钠对乳化液热稳定性的影响,乳化液的热变性时间(HCT)受pH值变化影响显著,添加三聚磷酸钠可以显著提高乳化液的热稳定性。 展开更多
关键词 婴儿配方 稳定性 乳化液稳定性
下载PDF
两种不同芯材制备的乳化液稳定性研究 被引量:4
3
作者 史昫皓 徐振波 +2 位作者 蒋将 李进伟 刘元法 《食品工业科技》 CAS CSCD 北大核心 2015年第17期49-52,57,共5页
以乳清蛋白和变性淀粉为壁材,氢化棕榈油和高油酸葵花籽油为芯材制备O/W乳化液,讨论了不同p H和均质压力对乳化液稳定性的影响。结果表明,乳化液在中性条件下乳液液滴平均粒径最小,体系的Zeta电位的绝对值高达42 m V,静电稳定性好。均... 以乳清蛋白和变性淀粉为壁材,氢化棕榈油和高油酸葵花籽油为芯材制备O/W乳化液,讨论了不同p H和均质压力对乳化液稳定性的影响。结果表明,乳化液在中性条件下乳液液滴平均粒径最小,体系的Zeta电位的绝对值高达42 m V,静电稳定性好。均质条件为35 MPa均质两次,得到的乳化液粒径可以维持在400 nm,均质两次后得到的乳化液稳定性最高。随着存储时间的延长,氢化棕榈油的乳化液体系油脂氧化程度高于高油酸葵花籽油,包埋在一定程度上可以延缓不饱和脂肪酸含量高的芯材的氧化。 展开更多
关键词 乳化液 乳化液稳定性 氧化稳定性 粉末油脂
下载PDF
再生纤维素凝胶对乳清分离蛋白预乳化液稳定性的影响 被引量:3
4
作者 赵尹毓 田筱娜 +1 位作者 周光宏 张万刚 《食品科学》 EI CAS CSCD 北大核心 2019年第6期16-21,共6页
利用再生纤维素(regenerated cellulose,RC)凝胶改善蛋白质预乳化液的乳化稳定性。考察添加量分别为0%、0.4%、0.8%、1.2%、1.6%的RC对乳清分离蛋白(whey protein isolate,WPI)-橄榄油预乳化液乳化稳定性、乳化活性、粒度大小、微观结... 利用再生纤维素(regenerated cellulose,RC)凝胶改善蛋白质预乳化液的乳化稳定性。考察添加量分别为0%、0.4%、0.8%、1.2%、1.6%的RC对乳清分离蛋白(whey protein isolate,WPI)-橄榄油预乳化液乳化稳定性、乳化活性、粒度大小、微观结构、流变特性的影响。结果表明,添加RC可以显著提高WPI预乳化液的乳化稳定性及乳化活性(P<0.05),RC添加量为0.8%时可以有效抑制乳化液的分层现象;随着RC添加量的增加,乳化液粒度大小及絮凝程度显著降低(P<0.05);乳化液流变学特性显示RC具有很好的增稠作用和凝胶性能。结果表明RC的添加对于WPI-预乳化液稳定性有很大影响,预乳化液中添加1.2%RC,可以有效增加乳化液黏度,获得较强的凝胶网络结构,显著降低粒度,改善乳化液稳定性。 展开更多
关键词 再生纤维素 乳清分离蛋白 乳化液稳定性 粒度大小 黏度
下载PDF
以大豆分离蛋白为壁材喷雾干燥法制备芥末油微胶囊 被引量:7
5
作者 盖旭 李荣 姜子涛 《中国调味品》 CAS 北大核心 2012年第3期72-75,共4页
以大豆分离蛋白为壁材,采用喷雾干燥法制备了芥末油微胶囊。其最佳工艺条件为:固形物含量10%、芯壁比1∶2、乳化剂的添加量为0.1%、均质时间4min(10000r/min)、喷雾干燥进风口温度195℃。在最佳工艺条件下得到的微胶囊产品的包埋率为89.... 以大豆分离蛋白为壁材,采用喷雾干燥法制备了芥末油微胶囊。其最佳工艺条件为:固形物含量10%、芯壁比1∶2、乳化剂的添加量为0.1%、均质时间4min(10000r/min)、喷雾干燥进风口温度195℃。在最佳工艺条件下得到的微胶囊产品的包埋率为89.94%。 展开更多
关键词 芥末 芥末油 大豆分离蛋白 乳化液稳定性 喷雾干燥
下载PDF
紫海胆黄油微胶囊制备工艺的研究 被引量:4
6
作者 徐清云 潘南 +4 位作者 陈丽娇 刘智禹 吴靖娜 苏永昌 苏捷 《渔业现代化》 2018年第2期73-80,共8页
为开发品质较好的紫海胆(Anthocidaris crassispina)黄油微胶囊,以辛烯基琥珀酸酯化淀粉(HICAP100)和β-环糊精为壁材,通过喷雾干燥制备紫海胆黄油微胶囊,以乳化液稳定性及包埋率为指标,通过单因素试验,研究紫海胆黄油微胶囊的壁材比例... 为开发品质较好的紫海胆(Anthocidaris crassispina)黄油微胶囊,以辛烯基琥珀酸酯化淀粉(HICAP100)和β-环糊精为壁材,通过喷雾干燥制备紫海胆黄油微胶囊,以乳化液稳定性及包埋率为指标,通过单因素试验,研究紫海胆黄油微胶囊的壁材比例、乳化液浓度及油脂添加量对微胶囊的影响。以单因素试验的结果为基础,采用正交实验得出紫海胆黄油微胶囊化的最优制备工艺,并检测其理化性质和卫生指标。结果显示,最优制备工艺为:壁材比例为4∶2(HI-CAP100∶β-环糊精),乳化液质量浓度为17%,油脂添加量为15%。经过分散机乳化30 min,利用料理机均质5 min,在进风温度180℃、出风温度80℃、进样速度500 mL/h下进行喷雾干燥时,得到的包埋率和乳化液稳定性分别为95.7%和96.8%,紫海胆黄油微胶囊的水分含量为2.82%,溶解度为71.94%,自流角为22.05°,菌落总数为480 CFU/g,大肠菌群数<30 MPN/100 g,霉菌和酵母<10 CFU/g,金黄色葡萄球菌、沙门氏菌、志贺氏菌皆未检出。紫海胆黄微胶囊的理化性质及安全卫生指标皆符合行业标准。 展开更多
关键词 紫海胆黄油 微胶囊 喷雾干燥 包埋率 乳化液稳定性
下载PDF
冷连轧乳液系统技术(一)——搅拌器应用
7
作者 范春 《液压气动与密封》 2017年第8期31-33,共3页
轧制工艺润滑是冷连轧轧制环节及其重要的一道工艺,直接影响冷轧产品的质量指标。该文从乳液搅拌器入手,分析了稳定性乳化液和弥散性乳液对箱体搅拌装置技术要求的差异。对搅拌器结构以及搅拌器与乳液箱匹配进行研究分析。
关键词 稳定性乳化液 弥散性乳液 搅拌器 应用
下载PDF
Investigation on Relationship between Lubricating Performance and Stability of Emulsion for Cold Strip Rolling 被引量:3
8
作者 Sun Jianlin Wang Yizhu +1 位作者 La Rui Wang Bing (School of Material Science and Engineering,University of Science and Technology Beijing,Beijing 100083) 《China Petroleum Processing & Petrochemical Technology》 SCIE CAS 2010年第3期54-58,共5页
The influence of the ratio and content of emulsifiers on the stability of anion emulsions for cold strip rolling was investigated in this paper. The present study also investigated the effects of HLB (hydrophile-lipo... The influence of the ratio and content of emulsifiers on the stability of anion emulsions for cold strip rolling was investigated in this paper. The present study also investigated the effects of HLB (hydrophile-lipophile balance) value and emulsifier content on the stability of no-ionic emulsions. Based on the effects of different stabilities and different concentrations of emulsions on the adsorptivity and friction coefficients, good lubricating performance was obtained when the amount of the separated oil and soap (SOS) accounted for 2.5%. The wearing scar of the steel balls also indicated the improvements in tribological properties after using the emulsion. Thus, the preparation of emulsion should be regulated according to different rolling conditions. 展开更多
关键词 LUBRICATION oil-water emulsion STABILITY lubricating performance
下载PDF
Kinetics for Describing the Creaming of Protein-Stabilized O/W Emulsions by Multiple Light Scattering
9
作者 Luis Alberto Panizzolo Luis Eduardo Mussio María Cristina Anon 《Journal of Food Science and Engineering》 2014年第5期236-243,共8页
In the present work, new kinetics to describe the creaming stability of oil-in-water emulsions determined by backscattering measurements (BS) is proposed. The emulsions assayed exhibited a different backscattering p... In the present work, new kinetics to describe the creaming stability of oil-in-water emulsions determined by backscattering measurements (BS) is proposed. The emulsions assayed exhibited a different backscattering profiles regarding creaming destabilization hyperbolic and sigmoid one. Hyperbolic behavior can be described by a second order kinetics, where k_h could be equaled to a rate constant that describes the creaming process and its values would indicate the stability of emulsions. While for the sigmoid BS pattern, kinetics with two terms, is adequate to describe the creaming process in contrast to kinetics previously reported in the literature. The kh value has the same meaning as before, and ks indicates the delaying effect on the creaming rate. 展开更多
关键词 EMULSION PROTEINS CREAMING KINETIC multiple light scattering.
下载PDF
Stability of Bitter Orange Juice-Olive Oil Salad Dressings Stabilized with Polysaccharides
10
作者 E. A. Ergelebi S. Kara E. ibanoglu 《Journal of Food Science and Engineering》 2011年第4期297-302,共6页
Emulsifying properties of bitter orange (Citrus aurantium) juice-olive oil salad dressings stabilized with different polysaccharides were investigated. Oil-in-water emulsions (50:50, v/v) were prepared with bitte... Emulsifying properties of bitter orange (Citrus aurantium) juice-olive oil salad dressings stabilized with different polysaccharides were investigated. Oil-in-water emulsions (50:50, v/v) were prepared with bitter orange juice-olive oil in the presence of various concentrations (0.1%-1.0%, w/v) of pectin or guar gum or iota-(t-)carrageenan and then these emulsions were homogenized. Emulsion activity index (EAI) and emulsion stability index (ESI) were determined spectrophotometrically by measuring time-dependent changes in turbidity. Creaming stability of emulsions was followed by visual observation of serum layer with respect to time. Microstructures of emulsions were examined by using polarized light microscopy. The addition of polysaccharides improved emulsion stability and emulsions containing higher amounts of polysaccharide were more stable against creaming. Microscopic observations showed that emulsions containing polysaccharides had small droplets as compared to that of emulsions without polysaccharides and emulsions were flocculated due to the presence of polysaccharides. Larger droplets and creaming were observed when the polysaccharide concentration was not sufficient for coverage. 展开更多
关键词 Bitter orange juice salad dressings EMULSION POLYSACCHARIDE microstructure.
下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部