风洞稳速压模糊控制系统

介绍西北工业大学ＮＦ－３低速翼型风洞稳速压控制系统的结构、控制原理和性能特点，由于采用了先进的模糊控制技术，传感器实时校准和变系数程控技术，解决了速压系统不建模自动调节，速压过程参数变化自适应和测量、控制、数据处理一体化等技术关键，使风洞速压控制达到高效和高品质性能。

多点静压落差法在风洞稳速压控制系统中的分析与应用

先介绍了两种测量风洞稳速压控制系统风速反馈值的常用方式-单点风速测量法和多点静压落差法,并对其特点和应用场合进行了分析;然后对多点静压落差法进行数学建模,给出了静压落差与风洞试验段中心点风速的关系;最后用一个工程实例说明此方法在实际风洞设计中的应用。

Fluidization characteristics of magnetic particles and determination of stable fluidization zone in magnetically fluidized bed

To determine and calculate the stable fluidization zone in a magnetically fluidized bed, the fluidization characteristics of magnetic particles are investigated. Four kinds of magnetic particles with different average diameters, ranging from 231 to 512 μm, are fluidized in the presence of magnetic fields with specified values of the intensity in the range of zero to 7330 A/m, and the particle fluidization curves are plotted. For marking the stable fluidization zone in the curves, the minimum bubbling velocities of particles are measured by the pressure-drop fluctuation. Based on the fluidization curves, the influences of the average particle diameter and magnetic field intensity on the zone are analyzed and discussed. A correlation to determine the stable fluidization zone is derived from the experimental data, using three dimensionless numbers, i. e., the ratio of magnetic potential to gravity potential, the Reynolds number and the Archimedes number. Compared with available data reported, it is shown that the correlation is more simplified to predict relative parameters for the bed operating in the state of stable fluidization under reasonable conditions.

Low-speed instability analysis for hydraulic motor based on nonlinear dynamics

A nonlinear dynamics model and a mathematical expression were set up to investigatethe mechanism and conditions of vibration creep acceleration.The model showsthat hydraulic spring and nonlinear friction are major factors that can affect low-speed instability.The mathematic model was established to obtain the change rule of speed andinstantaneous acceleration of the hydraulic motor.Then, Matlab was used to simulate theeffect of nonlinear friction force and hydraulic motor parameters such as coefficient of leakand compression ratio, etc., under low speed.Finally, some measures were proposed toimprove the low-speed stability of the hydraulic motor.

Wet Compression Performance of a Transonic Compressor Rotor at its Near Stall Point

In order to study the effects of wet compression on a transonic compressor,a full 3-D steady numerical simulation was carried out under varying conditions.Different injected water flow rates and droplet diameters were considered.The effect of wet compression on the shock,separated flow,pressure ratio,and efficiency was investigated.Additionally,the effect of wet compression on the tip clearance when the compressor runs in the near-stall and stall situations was emphasized.Analysis of the results shows that the range of stable operation is extended,and that the pressure ratio and inlet air flow rate are also increased at the near-stall point.In addition,it seems that there is an optimum size of the droplet diameter.

Analysis of grid-connected voltage stability of FSCWT based on bifurcation theory

This paper studies on the change mechanisms of the voltage stability caused by the grid connection of front-end speed-controlled wind turbines(FSCWT)integrating into power system.First of all,the differential algebraic equations describing the dynamic characteristics of wind turbines are illustrated.Then,under the guidance of IEEE3 node system model,the influence of the angular velocity of wind turbines,the reactive power and the active power at load bus on the voltage stability of grid-connection has been analyzed by using bifurcation theory.Finally,the method of linear-state feedback control has been applied to the original system in accordance with the bifurcation phenomenon of grid-connected voltage caused by the increase in the active power at load bus.Research shows that voltage at the grid-connected point would be changed with the fluctuation of turbines angular velocity.And increasing its reactive power can enhance voltage at the grid-connected point;problem of bifurcation at the grid-connected point can be delayed when increasing the gain k s of feedback controller within a certain range.

Unsteady Behavior of Surge and Rotating Stall in an Axial Flow Compressor

Unsteady behaviors as well as unsteady cascade flow fields of a single-stage axial flow compressor were experi- mentally investigated by detail measurements of unsteady performance characteristics and casing wall pressure and internal flow velocity fluctuations. The main feature of the test compressor is a capacity tank connected di- rectly to the compressor outlet in series through slits and a concentric duplex pipe, and also jet nozzles in order to inject compressed air toward the rotor tip region. Research attention is focused on the post-stall characteristics of surge and rotating stall which occur simultaneously. When the compressor was connected to the capacity tank, surge was generated with rotating stall in accordance with the capacitance increment of whole compressor system The surge behavior changed irregularly with throttling valve installed behind the compressor, and several types of surge cycles were observed. In addition, the surge cycle changed by jet injection to the rotor tip region. The re- suits suggested that the blockages of the cascade flow which were generated by a stall cell play an important role in deciding the surge behaviors.

Investigation on Multiple Cylindrical Holes Casing Treatment for Transonic Axial Compressor Stability Enhancement

Casing treatment is one possible way of regaining axial compressor operating range. However, most of casing treatments extend the operating range with the cost of efficiency penalty. A new form of multiple cylindrical holes casing treatment(MHCT) with pre-swirl blowing for the NASA Rotor-37 has been designed based on profound understanding of the stall inception. Unsteady numerical simulations have been performed for Rotor-37 with and without MHCT. Parametric studies of the total extraction holes area and their axial locations show that the compressor performance deteriorates as the area ratio increases but the stall margin is extended and there is an optimum extraction holes axial location for stall margin extending. The better configuration of MHCT could extend the stall margin by 6.2% with only 0.23% peak efficiency reduction. Detailed analysis of the physical mechanism behind the stall margin improvement shows that the casing treatment could eliminate the passage blockage by suppressing breakup of tip leakage vortex and decrease the blade load in tip region, which both contribute to improve stall margin of transonic axial compressors.

Series solution of unsteady peristaltic flow of a Carreau fluid in small intestines

The study of peristaltic flow of a Carreau fluid in a non-uniform tube under the con- sideration of long wavelength is presented. The flow is investigated in a wave frame of reference moving with velocity of the wave e. Numerical integration has been used to obtain the graphical results for pressure rise and frictional forces. The effects of various emerging parameters are investigated through graphs.

Impeller-diffuser interaction:analysis of the unsteady flow structures based on their direction of propagation

The present study is focused on the analysis of the deterministic fluctuations arising from the rotor-stator interaction within a transonic centrifugal compressor stage. A spectral analysis applied to the unsteady flow field leads to the values of the rotation speed of most energetic modes. From these values, the various structures are classified according to their direction of propagation which leads to a comprehensive description of the underlying mechanisms involved in the interaction.