陆上风电钢混组合结构塔架风致疲劳寿命识别方法

风致疲劳是长期积累的过程,单个风荷载事件可能不会导致结构的立即破坏,且不同材料和构件之间的相互作用、应力集中、局部应力等影响塔架受力关系,难以分析不同方向上的空气荷载力,因此,对疲劳寿命的识别精度不佳。对此,提出陆上风电钢混组合结构塔架风致疲劳寿命识别方法。利用SESAM/GeniE模块,将实际结构转化为有限元模型,计算出塔架结构不同方向上的空气动力荷载,并将其进行组合,即可得到综合荷载值;通过分析塔架外力荷载与疲劳寿命之间的关系,累加综合损伤值,即可得到塔架的风致疲劳寿命的识别结果。实验结果表明,采用文中所述识别方法对风电钢混组合结构塔架疲劳寿命进行识别时,随着风速的不断提高,相同节点处的塔架疲劳损伤量也有所变化,识别结果与实际情况之间的应力响应均方根较低,说明该方法具备较高的识别精度。

Superposability of unsteady aerodynamic loads on bridge deck sections

The 2-dimensional unsteady aerodynamic forces,in the context of both a thin airfoil where theory of potential flow is always applicable and a bluff bridge-deck section where separated flow is typically induced,are investigated from a point of view of whether or not they conform to the principle of linear superposition in situations of various structural motions and wind gusts.It is shown that some basic preconditions that lead to the linear superposability of the unsteady aerodynamic forces in cases of thin airfoil sections are no longer valid for a bluff section.Theoretical models of bridge aerodynamics such as the one related to flutter-buffeting analysis and those concerning aerodynamic admittance(AA)functions,however,necessitate implicitly this superposability.The contradiction revealed in this work may throw light on the perplexing problem of AA functions pertaining to the description of buffeting loads of bridge decks.Some existing theoretical AA models derived from flutter derivatives according to interrelations valid only for thin airfoil theories,which have been employed rather extensively in bridge aerodynamics,are demonstrated to be illogical.Finally,with full understanding of the preconditions of the applicability of linear superposability of the unsteady aerodynamic forces,suggestions in regard to experiment-based AA functions are presented.

Wind tunnel study of aerodynamic wind loading on middle pylon of Taizhou Bridge

Segment sectional model tests are carried out to investigate the wind loading on middle pylon of Taizhou Bridge, which has complicated three-dimensional flow due to its feature of double columns. Through the force measuring tests, aerodynamic force coefficients of every segment of the pylon columns have been obtained. It is found that the tested aerodynamic force coefficients are much smaller than those given by codes. The interference effects of aerodynamic force coefficients between columns of pylon are discussed. The results show that the interference effect is the most evident when the yaw angle is about 30 ° from transverse direction. This kind of interference effect can be described as diminutions in transverse aerodynamic force coefficients and magnifications in longitudinal aerodynamic force coefficients of downstream columns.

Coordination control strategy based on characteristic model for 3-bearing swivel duct nozzles

A coordination control strategy is developed for 3-bearing swivel duct （3BSD） nozzles. A 3BSD nozzle＇s deflection angle and direction are changed through rotations of three revolute pairs. There is a nonlinear relationship between the deflection an- gle/direction and the rotation angles. The rotation speed of a revolute pair is limited by the power of the actuator. The moment of inertia and the aerodynamic load for each revolute pair are different and time-varying. A high-precision control system of 3BSD nozzles is required for applications on vertical and/or short take-off and landing （V/STOL） aircrafts. Difficulties of co- ordination control of 3BSD nozzles are distinct travel ranges, speed constraints, time^xarying dynamic models, and disturb- ances. The proposed control strategy is a combination of the characteristic model and tlF e dynamic control allocation method. A dynamic control allocation module is used as the coordination supervisor, which is aware of the kinematic model, the con- straints, and the dynamic models of the revolute pairs. Second-order characteristic models are used to represent the dynamic behavior of the revolute pairs. The gradient projection algorithm is modified for parameter estimation. A modified all-coefficient adaptive controller is developed to reject the disturbances. Experimental results of a scaled 3BSD nozzle indi- cate that the coordination control strategy is effective.

The Effect of Variable Stator on Performance of a Highly Loaded Tandem Axial Flow Compressor Stage

Increasing the aerodynamic load on compressor blades helps to obtain a higher pressure ratio in lower rotational speeds. Considering the high aerodynamic load effects and structural concerns in the design process, it is possible to obtain higher pressure ratios compared to conventional compressors. However, it must be noted that imposing higher aerodynamic loads results in higher loss coemcients and deteriorates the overall performance. To avoid the loss increase, the boundary layer quality must be studied carefully over the blade suction surface. Employment of advanced shaped airfoils （like CDAs）, slotted blades or other boundary layer control methods has helped the de- signers to use higher aerodynamic loads on compressor blades. Tandem cascade is a passive boundary layer control method, which is based on using the flow momentum to control the boundary layer on the suction surface and also to avoid the probable separation caused by higher aerodynamic loads. In fact, the front pressure side flow momentum helps to compensate the positive pressure gradient over the aft blade＇s suction side. Also, in compari- son to the single blade stators, tandem variable stators have more degrees of freedom, and this issue increases the possibility of finding enhanced conditions in the compressor off-design performance. In the current study, a 3D design procedure for an axial flow tandem compressor stage has been applied to design a highly loaded stage. Following, this design is numerically investigated using a CFD code and the stage characteristic map is reported. Also, the effect of various stator stagger angles on the compressor performance and especially on the compressor surge margin has been discussed. To validate the CFD method, another known compressor stage is presented and its performance is numerically investigated and the results are compared with available experimental results.

Control of dynamic stall of helicopter rotor blades

An effective method for delaying the dynamic stall of helicopter retreating blade by using the trailing edge flap has been established in this paper.The aerodynamic loads of blade section are calculated by using the Leishman-Beddoes unsteady two-dimensional dynamic stall model and the aerodynamic loads of the trailing edge flap section are calculated by using the Hariharan-Leishman unsteady two-dimensional subsonic model.The analytical model for dynamic stall of elastic blade with the stiff trailing edge flap has been established.Adopting the aeroelastic analytical method and the Galerkin's method combined with numerical integration,the aeroelastic responses of rotor system in high-speed and high-load forward flight are solved.The mechanism for control of dynamic stall of retreating blade by using trailing edge flap has been presented.The numerical results indicate that the reasonably controlled swing of trailing edge flap can delay the dynamic stall of retreating blade under the same flight conditions.

The aeroelastic effects on the scatter phenomenon of wind-tunnel data

The unsteady Reynolds-averaged Navier-Stokes equations coupled with the k-co SST turbulence model are solved to obtain the steady and unsteady aerodynamic forces for airfoils and wings. The effects of vibration types and amplitudes on aerody- namic forces of airfoils and wings are studied. The deformation characteristics of a swept wing induced by steady aerodynamic load are presented. It is found that for a vibrating elastic wing at small and medium incidences, its mean aerodynamic loads are almost the same as those obtained from the static one. On the contrary, at high incidences especially around the stall incidence, the vibration may change the mean values. In addition, the larger amplitude is, the larger discrepancy will be. For a swept wing, the steady aerodynamic loads usually lead to the ＂pitching down＂ effect on the wing tip which delays the stall compared with a rigid one; But this phenomenon dose not occur on a aeroelastic wing which can induce the separation ahead and trigger the stall. The above conclusions are in good agreement with the scatter characteristics of wind-tunnel data. The reason why the data obtained from wind tunnel and CFD are different is also analyzed. Meanwhile, it can be an explanation for scatter phe- nomenon of wind-tunnel data, especially for high incidence cases, which remains a puzzle so far.