电容式空-油和油-水双界面传感器测量盲区的解决方法

为了解决现有分段电容式油水双界面传感器在某些情况下不能测量的缺陷,提出了一个简单实用的方法。具体做法是把每个测量段的非共用极板沿对角线分成了两部分,然后通过这两部分和另一共用极板间电容值与油水双界面之间的关系,推导得出了它们之间的理论公式,最后通过实验验证了所获得的油水双界面评价方法是完全可行的。

低频球面声波在水-空界面传播特性的研究

由于水和空气特性阻抗存在很大差异,传统的射线理论认为水-空界面的声透射性十分微弱。论文在射线方法的基础上,使用波动方法对球面声波跨水-空界面传播问题进行了深入研究。当声源位于水下较小深度时,随着频率的降低,被射线理论忽视了的非均匀波的作用显著加强,使得透射出水-空界面的声能量有了很大程度的增加。水下声能量随频率变化是由于直达波和界面反射波的干涉作用。射线结果是高频情况下波动结果的近似。

空中声源水下声场的简正波建模方法

空水界面声信号传播特性是水下检测空中声源首先要研究的问题,文中讨论了空中声源在水下产生声场的简正波模型,仿真分析了空中声源的水下声场,比较了简正波方法与射线方法、快速场方法对空中声源在水下产生的声场传播损失。结论表明简正波方法适用于远场传播损失。

适应水-空介质航行的共形半环翼布局概念研究

根据跨越水-空界面,在海水、空气两种介质中交替航行的构想,针对飞行器/航行器的气/水动布局设计矛盾,考虑穿越两相界面的巨大冲击载荷,基于可伸展环形翼设计,提出一种共形半环翼布局概念。设计了空中、水下两种基本布局形态,利用弹翼沿轴向对称旋转实现形态之间的过渡转换。采用CFX软件分析了该布局空中构型的气动特性和水下构型的水动特性。数值模拟结果表明,0°攻角时,共形半环翼布局空中构型气动升、阻力系数接近于具有相同翼型、弦长、水平投影面积的平直翼构型的两倍,攻角增大到12°以后,气动升力较参考平直翼构型的增幅降低到百分之十几;水下构型与类鱼雷构型水动特性相当;空中构型在水下航行时,弹翼阻力约占整体布局阻力的50%,弹翼升力在攻角绝对值大于15°时约占50%,随着攻角绝对值减小所占比例迅速增加,3°攻角时弹翼升力占到98%,从而证明共形半环翼布局为适应水-空介质航行所设计的两种构型及其变体方案的合理性及必要性。

洞穴碳酸钙沉积过程中的水体形状因素初探

在过去对于影响碳酸钙沉积因素研究的基础之上,通过对几种同体积的不同形状水体的CO2分布及逸出路径的实验研究,指出碳酸钙的沉积速度与水——空界面面积及CO2选出路径的关系,进而分析了洞穴碳酸钙沉积过程中不同水体形状对于沉积速度的影响。

Water, CO_2 and Energy Exchange at Vegetation-air Interface

[Objective] The aim was to analyze water and heat fluxes, CO2 fluxes and energy balance in wheat ecosystem in Luancheng County of Hebei Province. [Method] Based on data of water and heat flux, and CO2 fluxes, routine meteorological and biomass data in Luancheng in 2008, water and heat fluxes, CO2 fluxes and energy balance in wheat ecosystem were explored. [Result] The results showed that latent and sensible heat and CO2 fluxes were of obvious daily and seasonal changes; latent and sensible heat fluxes shaped an inverted U in daily change, and CO2 fluxes were of a U-shape; daily flux peak differed significantly. Furthermore, the change of latent heat, sensible heat and CO2 fluxes were closely related to environ- mental factors. Detailedly, the three were sensitive to light intensity and net radiation, and correlation coefficients were 0.92, 0.66, 0.65 and 0.90, 0.69, 0.74, respectively. Besides, the fluxes, sensitive to temperature, proved better in sunny day, especially for latent flux which is more sensitive to water in soils after precipitation. In addition, closure degree of energy balance in wheat fields was 0.91 and non-closure, caused by measurement error and neglection of heat storage, was observed, too. What＇s more. closure degree differed in months and time periods within a day. [Conclusion] The research concluded water and heat fluxes, CO2 fluxes, transport mechanisms and concerning factors, providing scientific reference for revealing mechanism of evapo- ration and heat dissipation of canopy, relationship between photosynthesis and water use efficiencyand energy distribution mechanism.

Carbon dioxide partial pressure and carbon fluxes of air-water interface in Taihu Lake, China

To obtain carbon dioxide （CO2） flux between water-air interface of Taihu lake, monthly water samplers at 14 sites and the local meteorological data of the lake were collected and analyzed in 1998. Carbon dioxide partial pressures （pCO2） at air-water interface in the lake were calculated using alkalinity, pH, ionic strength, active coefficient, and water temperature. The carbon fluxes at different sublakes and areas were estimated by concentration gradient between water and air in consideration of Schmidt numbers of 600 and daily mean windspeed at 10 m above water surface. The results indicated that the mean values of pCO2 in Wuli Lake,Meiliang Bay, hydrophyte area, west littoral zone, riverine mouths, and the open lake areas were 1 807.8±1 071.4（mean±standard deviation）μatm （latm=1.013 25×10^5pa）, 416.3±217.0μatm, 576.5±758.8μatm, 304.2±9.43.5μatm, 1 933.6±1 144.7 μatm, and 448.5±202.6μatm, respectively. Maximum and minimum pCO2 values were found in the hypertrophic （4 053.7μatm） and the eutrophic （3.2 μatm） areas. The riverine mouth areas have the maximum fluxes （82.0±62.8 mmol/m^2a）. But there was no significant difference between eutrophic and mesotrophic areas in pCO2 and the flux of CO2. The hydrophyte area, however, has the minimum （--0.58±12.9mmol/m^2a）. In respect to CO2 equilibrium, input of the rivers will obviously influence inorganic carbon distribution in the riverine estuary. For example, the annual mean CO2 flux in Zhihugang River estuary was 19 times of that in Meiliang Bay, although the former is only a part of the latter. The sites in the body of the lake show a clear seasonal cycle with pCO2 higher than atmospheric equilibrium in winter, and much lower than atmospheric in summer due to CO2 consumption by photosynthesis. The CO2 amount of the net annual evasion that enters the atmosphere is 28.42×10^4 t/a, of which those from the west littoral zone and the open lake account for 53.8% and 36.7%, respectively.

Numerical Investigation of Transmission of Low Frequency Sound Through a Smooth Air-water Interface

It is the traditional belief that sound transmission from water to the air is very weak due to a large contrast between air and water impedances. Recently, the enhanced sound transmission and anomalous transparency of air-water interface have been introduced. Anomalous transparency of air-water interface states that the sound generated by a submerged shallow depth monopole point source localized at depths less than 1/10 sound wavelength, can be transmitted into the air with omni-directional pattern. The generated sound has 35 times higher power compared to the classical ray theory prediction. In this paper, sound transmission through air-water interface for a localized underwater shallow depth source is examined. To accomplish this, two-phase coupled Helmholtz wave equations in two-phase media of air-water are solved by the commercial finite element based COMSOL Multiphysics software. Ratios of pressure amplitudes of different sound sources in two different underwater and air coordinates are computed and analyzed against non-dimensional ratio of the source depth （D） to the sound wavelength （λ）. The obtained results are compared with the experimental data and good agreement is displayed.

Vibrational Spectra and Adsorption of Trisiloxane Superspreading Surfactant at Air/Water Interface Studied with Sum Frequency Generation Vibrational Spectroscopy

The C-H stretch vibrational spectra of the trisiloxane superspreading surfactant Silwet L-77 （（CH3）3Si- O-Si（CH3）（C3H6）（OCH2CH2）7-8OCH3）-O-Si（CH3）3） at the air/water interface are measured with the surface Sum Frequency Generation Vibrational Spectroscopy （SFG-VS）. The spectra are dominated with the features from the -Si-CH3 groups around 2905 cm^-1 （symmetric stretch or SS mode） and 2957 ^-1 （mostly the asymmetric stretch or AS mode）, and with the weak but apparent contribution from the -O-CH2- groups around 2880 ^-1 （symmetric stretch or SS mode）. Comparison of the polarization dependent SFG spectra below and above the critical aggregate or micelle concentration （CAC） indicates that the molecular orientation of the C-H related molecular groups remained unchanged at different surface densities of the Silwet L-77 surfactant. The SFG-VS adsorption isotherm suggested that there was no sign of Silwet L-77 bilayer structure formation at the air/water interface. The Gibbs adsorption free energy of the Silwet surfactant to the air/water interface is -42.2±0.8kcal/mol, indicating the unusually strong adsorption ability of the Silwet L-77 superspreading surfactant.

Water oxidation sites located at the interface of Pt/SrTiO_(3) for photocatalytic overall water splitting

When a proton reduction cocatalyst is loaded on an n-type semiconductor for photocatalytic overall water splitting(POWS),the location of water oxidation sites is generally considered at the surface of the semiconductor due to upward band-bending of n-type semiconductor which may ease the transfer of the photogenerated holes to the surface.However,this is not the case for Pt/SrTiO_(3),a model semiconductor based photocatalyst for POWS.It was found that the photogenerated holes are more readily accumulated at the interface between Pt cocatalyst and SrTiO_(3) photocatalyst as probed by photo-oxidative deposition of PbO_(2),indicating that the water oxidation sites are located at the interface between Pt and SrTiO_(3).Electron paramagnetic resonance and scanning transmission electron microscope studies suggest that the interfacial oxygen atoms between Pt and SrTiO_(3) in Pt/SrTiO_(3) after POWS are more readily lost to form oxygen vacancies upon vacuum heat treatment,regardless of Pt loading by photodeposition or impregnation methods,which may serve as additional support for the location of the active sites for water oxidation at the interface.Density functional theory calculations also suggest that the oxygen evolution reaction more readily occurs at the interfacial sites with the lowest overpotential.These experimental and theoretical studies reveal that the more active sites for water oxidation are located at the interface between Pt and SrTiO_(3),rather than on the surface of SrTiO_(3).Hence,the tailor design and control of the interfacial properties are extremely important for the achievement or improvement of the POWS on cocatalyst loaded semiconductor photocatalyst.

Absolute Orientation of Molecules with Competing Hydrophilic Head Groups at the Air/Water Interface Probed with Sum Frequency Generation Vibrational Spectroscopy

The constructive or destructive spectral interference between the molecular groups oriented up and down at the interface in the sum-frequency generation （SFG） spectra provides a direct measurement of the absolute orientation of these molecular groups. This simple approach can be employed to interrogate absolute molecular orientations other than using the complex absolute phase measurement in the SFG studies. We used the -CN group in the p-cyanophenol （PCP） molecule as the internal phase standard, and we measured the phases of the SFG fields of the -CN groups in the 3,5-dimethyl-4-hydroxy-benzonitrile （35DMHBN） and 2,6-dimethyl-4-hydroxy-benzonitrile （26DMHBN） at the air/water interface by measuring the SFG spectra of the aqueous surfaces of the mixtures of the PCP, 35DMHBN, and 26DMHBN solutions. The results showed that the 35DMHBN had its -CN group pointing into the aqueous phase; while the 26DMHBN, similar to the PCP, had its -CN group pointing away from the aqueous phase. The tilt angles of the -CN group for both the 35DMHBN and 26DMHBN molecules at the air/water interface were around 25°-45° from the interface normal. These results provided insights on the understanding of the detailed balance of the competing factors, such as solvation of the polar head groups, hydrogen bonding and hydrophobic effects, etc., on influencing the absolute molecular orientation at the air/water interface.

Conformation and Orientation of Phospholipid Molecule in Pure Phospholipid Monolayer During Compressing

On the basis of energy conservation law and surface pressure isotherm, the conformation energy changes of dipalmitoylphosphatidylcholine （DPPC） and dipalmitoylphosphatidylglycerol （DPPG） in pure phospholipid rnonolayer at the air/water interface during compression are derived. The optimized conformations of phospholipids at absolute freedom state are simulated by Gaussian 98 software. Based on following assumptions： （1） the conformation energy change is mainly caused by the rotation of one special bond; （2） the atoms of glycerol near the water surface are active; （3） the rotation is motivated by hydrogen-bond action; （4） the rotation of bond is inertial, one simplified track of conformational change is suggested and the conformations of DPPC and DPPG at different states are determined by the plots of conformation energy change vs. dihedral angle. The thickness of the simulated phospholipid monolayer is consistent with published experimental result. According to molecular areas at different states, the molecular orientations in the compressing process are also developed.

PIV Studies on Turbulence Structure in Air/Water Interface with Wind-Induced Water Waves

When wind appears over the free surface, water waves and turbulence are generated by an interfacial shear stress. In particular, turbulent diffusion promotes significantly mass and momentum transport beneath the interface between the water and air significantly in ocean and lakes, and thus it is very important for global environment problems to reveal such turbulence property and coherent structure. Simultaneous measurements of velocities and free-surface elevation allow us to conduct reasonably the phase analysis of the coherent structure in interfacial shear layer. Furthermore, multi-point measurements such as PIV are very powerful to detect the space-time structure of coherent motions. Therefore, in the present study, we developed a specially designed PIV system which can measure the velocity components and surface-elevation fluctuation simultaneously by using two sets of high-speed cameras to reveal the coherent structure in the interfacial shear layer.

Thermal transfer experimental research of a horizontal tube evaporative condenser

The thermal resistances distribution in different wet-bulb temperatures, air velocities and spraying water densities were achieved by the experimental test. The fluctuation of the water film convection and the water-air interfacial thermal resistance were reviewed especially. In the distribution of thermal resistance, the rank of the thermal resistance proportion （from max to min） is air flow heat transfer resistance, heat transfer resistance between refrigerant and wall, water film convection resistance and wall heat transfer resistance. When the heat flux is constant, the total resistance lowers nearly along with the increasing of air flow and water spray density. But there are a best air flow value of 2.98 m/s and a best spray water density of 0.064 kg/（m ·s） respectively, if continue to increase them, condensation performance is not significantly improved any more. The test results are available to improve the evaporative condenser performance and the designing lever.

Nanopatterning of substrates by self-assembly in supramolecular block copolymer monolayer films

Many technological applications require templates with nanoscale patterns.Block copolymer self-assembly is a method of choice for obtaining a large variety of such patterns,with greatest flexibility achieved when combined with a supramolecular approach.One of the ways to fabricate block copolymer templates is the Langmuir-Blodgett (LB) technique.Here,we briefly summarize recent work with LB films of polystyrene-poly(4-vinyl pyridine) (PS-P4VP) mixed with 3-n-pentade cylphenol (PDP),illustrating the different types of patterns possible and the principles governing them.One interesting pattern that can be easily achieved with this system is the so-called "nanostrand network",which,when used as a template for gold deposition,can produce double striped lines of gold.Here,we show how this pattern can be modified by acetone swelling to give rise to gold monolayer ribbons with internal structure.The results also suggest new insights into the early stages of morphology formation at the air/water interface.

Interfacial assembly of a series of Cu(Ⅱ)-coordinated Schiff bases complexes:Orderly nanostructures and supramolecular chirality

Four achiral Cu(Ⅱ)-coordinated Schiff bases complexes containing aromatic structures were synthesized and their supramolecular assemblies at the air/water interface were investigated.All the compounds could be spread on water surface although they have no alkyl chains.The Schiff base complex molecules with naphthyl groups tended to form J-aggregate in the Langmuir-Blodgett(LB) films transferred from water surface.By investigation of atomic force microscopy,a multilayer film or three-dimensional structures were observed.It was interesting to note that the LB films of achiral compound Cu-NA with naphthyl segment and without methyl groups transferred from water surface showed chirality.The supramolecular chirality in the present LB films was suggested to be due to a cooperative stereoregular-stacking of the functional groups in a helical sense.This research work provides a helpful clue for regulating the nanostructures and supramolecular chiral assembly in organized films.

Surface pressure anisotropy and complex relaxation of silica nanoparticle monolayer at the air-water interface

We report the anisotropy effect and the relaxation dynamics of surface pressure of silica nanoparticle monolayer at the air-water interface. The anisotropy of surface pressure occurs when the water surface is fully covered by particles and becomes more prominent with the increase of surface concentration. Hence, the conception of surface tensor was proposed to characterize the monolayer properties. The dynamics of pressure relaxation involves three timescales which are related to the damping of surface fluctuation, rearrangement of particle rafts and particle motion inside each raft. The anisotropy decays when the layer is kept static and the process is accelerated remarkably by barrier oscillation. The underlying physics mechanism is also discussed in detail for the origin of pressure anisotropy and its decay dynamics.