单桩穿越大型溶洞的竖向承载特性分析

在大型溶洞地区,由于开挖不便、回填难度大等原因,处理溶洞较为困难,因而常常采用桥梁桩基直接穿越溶洞进入持力层的施工工艺,通过有限元仿真分析,分析了桩长、桩径、洞高以及洞跨对桩基极限承载力的影响,并利用灰色理论对洞高与洞跨影响下的桩基极限承载力的计算公式进行数据拟合,基于此提出了溶洞地区桩基础施工与设计的技术要点和注意事项。

3D finite elements analysis of vertically loaded composite piled raft

In recent years,a new type of foundation named composite piled raft foundation (also called long short composite piled raft) has been developed.Where designing shallow foundations would mean unacceptable settlement,or other environmental risks exist which could impair the structure in the future,composite piled raft foundations could be used.Finite element method was applied to study the behavior of this type of foundation subjected to vertical loading.In order to determine an optimal pile arrangement pattern which yields the minimum settlement,various pile arrangements under different vertical stress levels were investigated.Results show that with increasing the vertical stress on the raft,the effectiveness of the arrangements of short and long piles become more visible.In addition,a new factor named "composite piled raft efficiency" (CPRE) has been defined which determines the efficiency of long short piles arrangement in a composite piled raft foundation.This factor will increase when short piles take more axial stresses and long piles take less axial stresses.In addition,it is found that the changes in settlements for different long short piles arrangement are in a well agreement with changes in values of CPRE ratio.Thus,CPRE ratio can be used as a factor to determine the efficiency of piles arrangements in composite piled raft foundation from the view point of reducing raft settlements.

A Theoretical Analysis of the Bearing Performance of Vertically Loaded Large-Diameter Pipe Pile Groups

This paper aims to present a theoretical method to study the bearing performance of vertically loaded large-diameter pipe pile groups.The interactions between group piles result in different bearing performance of both a single pile and pile groups.Considering the pile group effect and the skin friction from both outer and inner soils,an analytical solution is developed to calculate the settlement and axial force in large-diameter pipe pile groups.The analytical solution was verified by centrifuge and field testing results.An extensive parametric analysis was performed to study the bearing performance of the pipe pile groups.The results reveal that the axial forces in group piles are not the same.The larger the distance from central pile,the larger the axial force.The axial force in the central pile is the smallest,while that in corner piles is the largest.The axial force on the top of the corner piles decreases while that in the central pile increases with increasing of pile spacing and decreasing of pile length.The axial force in side piles varies little with the variations of pile spacing,pile length,and shear modulus of the soil and is approximately equal to the average load shared by one pile.For a pile group,the larger the pile length is,the larger the influence radius is.As a result,the pile group effect is more apparent for a larger pile length.The settlement of pile groups decreases with increasing of the pile number in the group and the shear modulus of the underlying soil.

Experimental study on load bearing behavior of large-scaled caps with pile groups

The objective of this investigation was to study the behavior of deep pile caps and the ultimate load-carrying capacity. Four 1/10 scaled models of nine-pile caps were cast and tested on vertical loads to failure. The destruction shapes of pile caps,the correlation between load and displacement,and the internal stresses were analyzed systematically. The results demonstrated that the failures of all the four models are resulted from punching shear; the internal flow of the forces in nine-pile caps can be approximated by "strut-and-tie" model. Furthermore,the failure loads of these specimens were predicted by some of the present design methods and the calculated results were compared with the experimental loads. The comparative results also indicated that the "strut-and-tie" model is a more reasonable design method for deep pile caps design.